UMB10N

EMB10 / UMB10N / IMB10A Transistors General purpose (dual digital transistors) EMB10 / UMB10N / IMB10A Features 1) Two DTA123J chips in a EMT or UMT or SMT package. 2) Mounting possible with EMT3 or UMT3 or SMT3 automatic mounting machines. 3) Transistor elements are independent, eliminating interference. 4) Mounting cost and area can be cut in half. Dimensions (Unit : mm) EMB10 (6) (5) (4) (1) (2) (3) Each lead has same dimensions ROHM : EMT6 Abbreviated symbol : B10 Structure Epitaxial planar type PNP silicon transistor (Built-in resistor type) UMB10N (6) (5) (4) The following characteristics apply to both DTr1 and DTr2. (1) (2) (3) Each lead has same dimensions Equivalent circuit EMB10 / UMB10N (3) (2) (1) R1 R2 DTr1 R1=2.2kΩ R2=47kΩ DTr2 R2 R1 (4) (5) DTr2 R2 R1 (3) (2) ROHM : UMT6 EIAJ : SC-88 Abbreviated symbol : B10 IMB10A (4) (5) (6) R1 R2 DTr1 R1=2.2kΩ R2=47kΩ (1) (4) (5) (6) IMB10A (6) Absolute maximum ratings (Ta = 25°C) Parameter Supply voltage Input voltage Symbol VCC VIN IO IC (Max.) Pd Tj Tstg Limits −50 −12 5 Output current EMB10, UMB10N Power dissipation IMB10A Junction temperature Storage temperature −100 −100 150 (TOTAL) 300 (TOTAL) 150 −55 to +150 ˚C ˚C Unit V V (3) (2) (1) Each lead has same dimensions ROHM : SMT6 EIAJ : SC-74 Abbreviated symbol : B10 mA ∗1 ∗2 mW ∗1 120mW per element must not be exceeded. ∗2 200mW per element must not be exceeded. Rev.C 1/2 EMB10 / UMB10N / IMB10A Transistors Electrical characteristics (Ta = 25°C) Parameter Input voltage Output voltage Input current Output current DC current gain Transition frequency Input resistance Resistance ratio Symbol VI (off) VI (on) VO (on) II IO (off) GI fT R1 R2 / R1 Min. − −1.1 − − − 80 − 1.54 17 Typ. − − −0.1 − − − 250 2.2 21 Max. −0.5 − −0.3 −3.6 −0.5 − − 2.86 26 Unit V V mA µA − MHz kΩ − Conditions VCC=−5V, IO=−100µA VO=−0.3V, IO=−5mA IO/II=−5mA/−0.25mA VI=−5V VCC=−50V, VI=0V VO=−5V, IO=−10mA VCE=−10V, IE=5mA, f=100MHz − − ∗ ∗ Transition frequency of the device Packaging specifications Package Type Code Basic ordering unit (pieces) EMB10 UMB10N IMB10A T2R 8000 Taping TN 3000 T110 3000 Electrical characteristic curves −100 −50 VO=−0.3V −10m −5m −2m VCC=−5V DC CURRENT GAIN : GI 1k 500 200 100 50 20 10 5 2 1 VO=−5V Ta=100˚C 25˚C −40˚C INPUT VOLTAGE : VI (on) (V) −20 −10 −5 −2 −1 OUTPUT CURRENT : Io (A) −1m −500µ −200µ −100µ −50µ −20µ −10µ −5µ −2µ Ta=−40˚C 25˚C 100˚C Ta=100˚C 25˚C −40˚C −500m −200m −100m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m −100m −1µ 0 −0.5 −1 −1.5 −2 −2.5 −3 −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) INPUT VOLTAGE : VI (off) (V) OUTPUT CURRENT : IO (A) Fig.1 Input voltage vs. output current (ON characteristics) −1 −500m Fig.2 Output current vs. input voltage (OFF characteristics) Fig.3 DC current gain vs. output current lO/lI =20 Ta=100˚C 25˚C −40˚C OUTPUT VOLTAGE : VO (on) (V) −200m −100m −50m −20m −10m −5m −-2m −1m −100µ −200µ −500µ −1m −2m −5m −10m −20m −50m−100m OUTPUT CURRENT : IO (A) Fig.4 Output voltage vs. output current Rev.C 2/2 Appendix Notes No technical content pages of this document may be reproduced in any form or transmitted by any means without prior permission of ROHM CO.,LTD. The contents described herein are subject to change without notice. The specifications for the product described in this document are for reference only. Upon actual use, therefore, please request that specifications to be separately delivered. Application circuit diagrams and circuit constants contained herein are shown as examples of standard use and operation. Please pay careful attention to the peripheral conditions when designing circuits and deciding upon circuit constants in the set. Any data, including, but not limited to application circuit diagrams information, described herein are intended only as illustrations of such devices and not as the specifications for such devices. ROHM CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any third party's intellectual property rights or other proprietary rights, and further, assumes no liability of whatsoever nature in the event of any such infringement, or arising from or connected with or related to the use of such devices. Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or otherwise dispose of the same, no express or implied right or license to practice or commercially exploit any intellectual property rights or other proprietary rights owned or controlled by ROHM CO., LTD. is granted to any such buyer. Products listed in this document are no antiradiation design. The products listed in this document are designed to be used with ordinary electronic equipment or devices (such as audio visual equipment, office-automation equipment, communications devices, electrical appliances and electronic toys). Should you intend to use these products with equipment or devices which require an extremely high level of reliability and the malfunction of which would directly endanger human life (such as medical instruments, transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other safety devices), please be sure to consult with our sales representative in advance. It is our top priority to supply products with the utmost quality and reliability. However, there is always a chance of failure due to unexpected factors. Therefore, please take into account the derating characteristics and allow for sufficient safety features, such as extra margin, anti-flammability, and fail-safe measures when designing in order to prevent possible accidents that may result in bodily harm or fire caused by component failure. ROHM cannot be held responsible for any damages arising from the use of the products under conditions out of the range of the specifications or due to non-compliance with the NOTES specified in this catalog. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact your nearest sales office. ROHM Customer Support System www.rohm.com Copyright © 2008 ROHM CO.,LTD. THE AMERICAS / EUROPE / ASIA / JAPAN Contact us : webmaster@ rohm.co. jp 21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan TEL : +81-75-311-2121 FAX : +81-75-315-0172 Appendix1-Rev2.0