LA6358NJ

Ordering number : ENA0289 Monolithic Linear IC LA6358NJ Overview High-Performance Dual Operational Amplifier The LA6358NJ is a high-performance dual operational amplifier that can operate from a single voltage power supply. It features a built-in phase correction circuit. It can also operate from a dual power supply with both positive and negative levels and features low power consumption. The LA6358NJ can be used in a wide range of industrial applications as a transducer amplifier for all types of transducers, as a DC amplifier circuit, and for other purposes as well. Functions • High-performance dual operational amplifier Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Differential input voltage Maximum input voltage Allowable power dissipation Operating temperature Storage temperature Symbol VCC max VID VIN max Pd max Topg Tstg Ta≤25°C Conditions Ratings 32 32 -0.3 to +32 570 -40 to +85 -55 to +150 Unit V V V mW °C °C Recommended Operating Conditions at Ta = -40 to +85°C Parameter Supply voltage Symbol VCC Conditions min 3 Ratings typ max 24 V Unit Any and all SANYO Semiconductor products described or contained herein do not have specifications that can handle applications that require extremely high levels of reliability, such as life-support systems, aircraft's control systems, or other applications whose failure can be reasonably expected to result in serious physical and/or material damage. Consult with your SANYO Semiconductor representative nearest you before using any SANYO Semiconductor products described or contained herein in such applications. SANYO Semiconductor assumes no responsibility for equipment failures that result from using products at values that exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other parameters) listed in products specifications of any and all SANYO Semiconductor products described or contained herein. 92706 / 40506 MS OT 20051206-S00002 No.A0289-1/6 LA6358NJ Electrical Characteristics at Ta = 25°C, VCC = 5V Parameter Input offset voltage Input offset current Input bias current Common-mode input voltage range Common-mode rejection ratio Large-amplitude voltage gain Output voltage range Supply voltage rejection ratio Channel separation Current drain Output current (source) Output current (sink) Symbol VIO IIO IB VICM CMR VG VOUT SVR CS ICC IO source IO sink VIN+ = 1V, VIN - = 0V VIN+ = 0V, VIN - = 1V f = 1k to 20kHz 11 7 8 9 10 10 7 VCC = 30V VCC = 15V, RL≥2kΩ IIN(+)/IIN(-) IIN(+)/IIN(-) Conditions Test Circuit 1 2 3,4 5 5 6 0 65 25 0 65 100 120 0.5 20 20 1.2 80 100 VCC-1.5 Ratings min typ ±2 ±5 45 max ±7 ±50 250 VCC-1.5 mV nA nA V dB V/mV V dB dB mA mA mA Unit Package Dimensions unit : mm 3001C 9.14 8 5 7.62 6.4 1.0 1 4 0.51min (3.0) 0.5 (0.76) 2.54 1.4 3.2 3.9max SANYO : DIP8(300mil) Pin Assignment 0.25 No.A0289-2/6 LA6358NJ Equivalent Circuit Test Circuits 1. Input offset voltage VIO 2. Input offset current IIO 3. Input bias current IB (−) 4. Input bias current IB (+) No.A0289-3/6 LA6358NJ 5. Common-mode rejection ratio CMR Common-mode input voltage range VICN 6. Voltage gain VG 7. Channel separation CH sep 8. Current drain ICC 9. Output current IO source 10. Output current IO sink No.A0289-4/6 LA6358NJ 11. Supply voltage rejection ratio SVR (+) 12. Supply voltage rejection ratio SVR (−) No.A0289-5/6 LA6358NJ Application Circuit Examples Noninverting DC amplifier Inverting AC amplifier Square wave generator Specifications of any and all SANYO Semiconductor products described or contained herein stipulate the performance, characteristics, and functions of the described products in the independent state, and are not guarantees of the performance, characteristics, and functions of the described products as mounted in the customer's products or equipment. To verify symptoms and states that cannot be evaluated in an independent device, the customer should always evaluate and test devices mounted in the customer's products or equipment. SANYO Semiconductor Co., Ltd. strives to supply high-quality high-reliability products. However, any and all semiconductor products fail with some probability. It is possible that these probabilistic failures could give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire, or that could cause damage to other property. When designing equipment, adopt safety measures so that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective circuits and error prevention circuits for safe design, redundant design, and structural design. In the event that any or all SANYO Semiconductor products (including technical data,services) described or contained herein are controlled under any of applicable local export control laws and regulations, such products must not be exported without obtaining the export license from the authorities concerned in accordance with the above law. No part of this publication may be reproduced or transmitted in any form or by any means, electronic or mechanical, including photocopying and recording, or any information storage or retrieval system, or otherwise, without the prior written permission of SANYO Semiconductor Co., Ltd. Any and all information described or contained herein are subject to change without notice due to product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification" for the SANYO Semiconductor product that you intend to use. Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO Semiconductor believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April, 2006. Specifications and information herein are subject to change without notice. PS No.A0289-6/6