SKY13489-001

DATA SHEET SKY13489-001: 0.7 to 2.7 GHz SPDT High Power Switch (Single Bit Control) in a WLCSP Package Applications  LTE TDD/FDD transmit  GSM transmit  Embedded modules RF1 ANT RF2 Features  Broadband frequency range: 0.7 to 2.7 GHz  Low insertion loss: 0.3 dB @ 2.7 GHz  High isolation: 22 dB up to 2.7 GHz  No external DC blocking capacitors required  Single GPIO control line with VDD voltage regulator:  VCTL = 1.35 to 3.00 V  VDD = 2.45 to 4.80 V  Small, 6-bump WLCSP, 217 μm diameter, 400 μm pitch (1.135 x 0.735 x 0.400 mm) package (MSL1, 260 °C per JEDEC J-STD-020) Skyworks GreenTM products are compliant with all applicable legislation and are halogen-free. For additional information, refer to Skyworks Definition of GreenTM, document number SQ04–0074. Logic and Supply 202857-001 VDD V1 Figure 1. SKY13489-001 Block Diagram Description The SKY13489-001 is a single-pole, double-throw (SPDT) LTE/WCDMA/GSM transmit switch. Switching is controlled by an integrated GPIO interface with a single control pin. Depending on the logic voltage level applied to the control pin, the antenna port is connected to one of the switched RF outputs (RF1 or RF2) through a low insertion loss path, while the path between the antenna port and the other RF port is in a high isolation state. No external DC blocking capacitors are required as long as no DC voltage is applied on any RF path. Pin A1 Indicator RF1 ANT RF2 A V1 GND VDD B 1 2 3 202857-002 Figure 2. SKY13489-001 Pinout (Top View, Bumps Facing Down) The SKY13489-001 is provided in a compact 6-bump, 1.135 x 0.735 x 0.400 mm Wafer Level Chip Scale Package (WLCSP) that meets requirements for board-level assembly. Bump diameters are 217 microns with a minimum bump pitch of 400 microns. A functional block diagram is shown in Figure 1. The pin configuration and package are shown in Figure 2. Signal pin assignments and functional pin descriptions are provided in Table 1. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202857D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 29, 2017 1 DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH Table 1. SKY13489-001 Signal Descriptions Pin Name Description Pin Name Description A1 RF1 RF I/O. Throw 1 of the switch. B1 V1 A2 ANT Antenna B2 GND Ground A3 RF2 RF I/O. Throw 2 of the switch. B3 VDD Supply voltage Electrical and Mechanical Specifications Digital control input The state of the SKY13489-001 is determined by the logic provided in Table 6. The absolute maximum ratings of the SKY13489-001 are provided in Table 2. Electrical specifications are provided in Tables 3 through 5. Table 2. SKY13489-001 Absolute Maximum Ratings1 Parameter Symbol Minimum Maximum Units Supply voltage VDD 2.4 5.0 V Digital control voltage VCTL –0.2 +3.2 V RF input power PIN +39 dBm Operating temperature TOP –40 +90 C Storage temperature TSTG –55 +150 C 1 Exposure to maximum rating conditions for extended periods may reduce device reliability. There is no damage to device with only one parameter set at the limit and all other parameters set at or below their nominal value. Exceeding any of the limits listed here may result in permanent damage to the device. ESD HANDLING: Although this device is designed to be as robust as possible, electrostatic discharge (ESD) can damage this device. This device must be protected at all times from ESD when handling or transporting. Static charges may easily produce potentials of several kilovolts on the human body or equipment, which can discharge without detection. Industry-standard ESD handling precautions should be used at all times. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 2 August 29, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202857D DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH Table 3. SKY13489-001 Electrical Specifications1 (1 of 2) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units DC Specifications Supply voltage VDD 2.45 2.85 4.80 V Control voltage: Low High V1_L V1_H –0.1 +1.35 0 +1.80 +0.45 +3.0 V V Current on V1 pin I_CTL 1 μA Supply current IDD 45 μA 20 μs 5 μs 20 mVpp 0.35 0.45 0.50 dB dB dB VDD = 2.65 V, V1 = VCTL_H DC supply turn-on/turn-off time tON Measured from 50% of final VDD supply voltage to 90% of final RF power RF path switching time tSW From one active state to another active state transition, measured from 50% of final control voltage to 90% of final RF power Supply ripple 30 2 VPP RF Specifications Insertion loss (RF1 or RF2 to ANT pin) IL 700 to 960 MHz 1710 to 2170 MHz 2170 to 2690 MHz Isolation (ANT to RF1 or RF2) ISO 700 to 960 MHz 1710 to 2170 MHz 2170 to 2690 MHz Voltage standing wave ratio, all ports VSWR Referenced to 50 Ω, 700 to 2690 MHz Compression point P0.2dB 700 to 2690 MHz 0.25 0.30 0.30 31 23 20 1.1:1 +37 dB dB db 32 25 22 1.2:1 +39 dBm Large Signal Specifications Harmonic power, ANT to RF1 or RF2 (VSWR = 1:1) fo = 824 to 915 MHz, PIN = +35 dBm: 2fo 3fo –65 –63 –60 –55 dBm dBm fo = 1710 to 1910 MHz, PIN = +33 dBm: 2fo 3fo –74 –71 –68 –65 dBm dBm fo = 824 to 960 MHz, PIN = +25 dBm: 2fo 3fo –82 –82 –78 –75 dBm dBm fo = 1710 to 1910 MHz, PIN = +25 dBm: 2fo 3fo –80 –78 –75 –73 dBm dBm fo = 1910 to 2690 MHz, PIN = +25 dBm: 2fo 3fo –68 –69 dBm dBm Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202857D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 29, 2017 3 DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH Table 3. SKY13489-001 Electrical Specifications1 (2 of 2) (VDD = 2.85 V, TOP = +25 C, Characteristic Impedance [ZO] = 50 Ω, Unless Otherwise Noted) Parameter Symbol Test Condition Min Typical Max Units –110 –120 –105 –110 dBm dBm –120 –120 –110 –110 dBm dBm Large Signal Specifications (continued) Second order intermodulation distortion, ANT to RF1 or RF2 IMD2 CW carrier = +20 dBm, CW blocker = –15 dBm: Band 1 Band 5 Third order intermodulation distortion, ANT to RF1 or RF2 IMD3 CW carrier = +20 dBm, CW blocker = –15 dBm: Band 1 Band 5 1 Performance is guaranteed only under the conditions listed in this table. Table 4. Third Order Intermodulation Distortion Frequencies fTX (MHz) fBLOCK 1 (MHz) fBLOCK 3 (MHz) Minimum Maximum Minimum Maximum fBLOCK 2 (MHz) Minimum Maximum Band 1 1920 1980 1730 1790 95.0 5950 6130 Band 2 1850 1910 1770 1830 40.0 5630 5810 Band 3 1710 1785 1615 1690 47.5 5225 5450 Band 4 824 849 779 804 22.5 2517 2592 Band 8 880 915 835 870 22.5 2685 2790 IMD3 Band Table 5. Second Order Intermodulation Distortion Frequencies fTX (MHz) fBLOCK 2 (MHz) Minimum Maximum fBLOCK 1 Minimum (MHz) Minimum Maximum Band 1 1920 1980 190 3650 3770 Band 2 1850 1910 80 3620 3740 Band 3 1710 1785 95 3325 3475 Band 5 824 849 45 1603 1653 Band 7 2500 2570 120 4880 5020 Band 8 880 915 45 1715 1785 Band 10 1710 1770 400 3020 3140 IMD2 Band Table 6. SKY13489-001 Truth Table1 State Active Path V1 (Bump B1) 0 ANT to RF1 0 1 ANT to RF2 1 1 “1” = 1.35 V to 3.00 V. “0” = –0.1 V to +0.45 V. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 4 August 29, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202857D DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH Evaluation Board Description The SKY13489-001 Evaluation Board is used to test the performance of the SKY13489-001 SPDT Switch. An Evaluation Board schematic diagram is provided in Figure 3. An assembly drawing for the Evaluation Board is shown in Figure 4. Antenna A2 A1 RF1 Switch Control B1 RF1 V1 ANT GND RF2 VDD A3 RF2 R1 0Ω B3 C2 DNP C1 DNP C3 DNP Voltage Supply B2 Ground 202857-003 Figure 3. SKY13489-001 Evaluation Board Schematic Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202857D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 29, 2017 5 DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH 202857-004 Figure 4. SKY13489-001 Evaluation Board Assembly Diagram Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 6 August 29, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202857D DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH Package Dimensions Package and Handling Information The typical part marking for the SKY13489-001 is shown in Figure 5.The PCB layout footprint for the SKY13489-001 is shown in Figure 6. Package dimensions for the SKY13489-001 die are shown in Figure 7, and tape and reel dimensions are provided in Figure 8. Instructions on the shipping container label regarding exposure to moisture after the container seal is broken must be followed. Otherwise, problems related to moisture absorption may occur when the part is subjected to high temperature during solder assembly. The SKY13489-001 is rated to Moisture Sensitivity Level 1 (MSL1) at 260 °C. It can be used for lead or lead-free soldering. For additional information, refer to the Skyworks Application Note, Wafer Level Chip Scale Packages: SMT Process Guidelines and Handling Considerations, document number 201676. Care must be taken when attaching this product, whether it is done manually or in a production solder reflow environment. Production quantities of this product are shipped in a standard tape and reel format. 202857-005 Figure 5. SKY13489-001 PCB Layout Footprint Pin 1 Indicator Part Code Last 4 Digits of Wafer ID 202857-006 Figure 6. Typical Part Marking Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202857D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 29, 2017 7 0.150 Min 0.400 ± 0.008 0.411 Max 0 1.135 ± 0.025 0.400 ± 0.008 DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH 0.225 ± 0.020 6X ø0.217 ± 0.032 CL 0.150 Min A 0.200 ± 0.008 A 0 CL 0.735 ± 0.025 Bump A1 Indicator (ø0.100 Min.) 0.200 ± 0.008 B 1 2 See Note 4 3 Bump Side Down B 0.151 Nom 3 Side View 2 1 Bump Side Up Notes: 1. 2. 3. 4. All measurements are in millimeters. Marking shown is for package orientation reference only. Ball height tolerance is ±10% of nominal ball height. Package thickness includes backside laminate film. 202857-007 Figure 7. SKY13489-001 Package Dimensions 2.00 ± 0.05 Pin 1 ø1.50 +0.10 4.00 ± 0.10 0.25 ± 0.02 1.75 ± 0.10 B 3.50 ± 0.05 8.00 +0.30 –0.10 1.31 ± 0.05 (Bo) B 0.91 ± 0.05 (Ao) ø0.40 ± 0.05 4.00 ± 0.10 0.47 ± 0.05 (Ko) A A 3° Max Detail B Notes: 1. Carrier tape must meet all requirements of Skyworks GP01-D233 procurement spec for tape and reel shipping. 2. Carrier tape material: black conductive polystyrene or polycarbonate. 3. Cover tape material: transparent conductive. 4. ESD surface resistivity must meet GP01-D233. 5. 10-sprocket hole pitch cumulative tolerance: ±0.20 mm. 6. Pocket position relative to sprocket hole measured as true position of pocket. 7. All dimensions are in millimeters. Detail A Figure 8. SKY13489-001 Tape and Reel Dimensions Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 8 August 29, 2017 • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • 202857D 202857-008 DATA SHEET • SKY13489-001: SPDT HIGH POWER SWITCH Ordering Information Model Name SKY13489-001: 0.7 to 2.7 GHz SPDT Switch in a WLCSP Package Manufacturing Part Number SKY13489-001 Evaluation Board Part Number SKY13489-001-EVB Copyright © 2014-2015, 2017 Skyworks Solutions, Inc. All Rights Reserved. Information in this document is provided in connection with Skyworks Solutions, Inc. (“Skyworks”) products or services. These materials, including the information contained herein, are provided by Skyworks as a service to its customers and may be used for informational purposes only by the customer. Skyworks assumes no responsibility for errors or omissions in these materials or the information contained herein. Skyworks may change its documentation, products, services, specifications or product descriptions at any time, without notice. Skyworks makes no commitment to update the materials or information and shall have no responsibility whatsoever for conflicts, incompatibilities, or other difficulties arising from any future changes. No license, whether express, implied, by estoppel or otherwise, is granted to any intellectual property rights by this document. Skyworks assumes no liability for any materials, products or information provided hereunder, including the sale, distribution, reproduction or use of Skyworks products, information or materials, except as may be provided in Skyworks Terms and Conditions of Sale. THE MATERIALS, PRODUCTS AND INFORMATION ARE PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, WHETHER EXPRESS, IMPLIED, STATUTORY, OR OTHERWISE, INCLUDING FITNESS FOR A PARTICULAR PURPOSE OR USE, MERCHANTABILITY, PERFORMANCE, QUALITY OR NON-INFRINGEMENT OF ANY INTELLECTUAL PROPERTY RIGHT; ALL SUCH WARRANTIES ARE HEREBY EXPRESSLY DISCLAIMED. SKYWORKS DOES NOT WARRANT THE ACCURACY OR COMPLETENESS OF THE INFORMATION, TEXT, GRAPHICS OR OTHER ITEMS CONTAINED WITHIN THESE MATERIALS. SKYWORKS SHALL NOT BE LIABLE FOR ANY DAMAGES, INCLUDING BUT NOT LIMITED TO ANY SPECIAL, INDIRECT, INCIDENTAL, STATUTORY, OR CONSEQUENTIAL DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR LOST PROFITS THAT MAY RESULT FROM THE USE OF THE MATERIALS OR INFORMATION, WHETHER OR NOT THE RECIPIENT OF MATERIALS HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. Skyworks products are not intended for use in medical, lifesaving or life-sustaining applications, or other equipment in which the failure of the Skyworks products could lead to personal injury, death, physical or environmental damage. Skyworks customers using or selling Skyworks products for use in such applications do so at their own risk and agree to fully indemnify Skyworks for any damages resulting from such improper use or sale. Customers are responsible for their products and applications using Skyworks products, which may deviate from published specifications as a result of design defects, errors, or operation of products outside of published parameters or design specifications. Customers should include design and operating safeguards to minimize these and other risks. Skyworks assumes no liability for applications assistance, customer product design, or damage to any equipment resulting from the use of Skyworks products outside of stated published specifications or parameters. Skyworks and the Skyworks symbol are trademarks or registered trademarks of Skyworks Solutions, Inc., in the United States and other countries. Third-party brands and names are for identification purposes only, and are the property of their respective owners. Additional information, including relevant terms and conditions, posted at www.skyworksinc.com, are incorporated by reference. Skyworks Solutions, Inc. • Phone [781] 376-3000 • Fax [781] 376-3100 • sales@skyworksinc.com • www.skyworksinc.com 202857D • Skyworks Proprietary Information • Products and Product Information are Subject to Change Without Notice • August 29, 2017 9