M74HC4518
DUAL DECADE COUNTER
s
s
s
s
s
s
s
HIGH SPEED : fMAX = 60 MHz (TYP.) at VCC = 6V LOW POWER DISSIPATION: ICC =4µA(MAX.) at TA=25°C HIGH NOISE IMMUNITY: VNIH = V NIL = 28 % VCC (MIN.) SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 4mA (MIN) BALANCED PROPAGATION DELAYS: tPLH ≅ tPHL WIDE OPERATING VOLTAGE RANGE: VCC (OPR) = 2V to 6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES 4518
DIP
SOP
TSSOP
ORDER CODES
PACKAGE DIP SOP TSSOP TUBE M74HC4518B1R M74HC4518M1R T&R M74HC4518RM13TR M74HC4518TTR
DESCRIPTION The M74HC4518 is an high speed CMOS DUAL BINARY COUNTER fabricated with silicon gate C2MOS technology. It consist of two identical internally synchronous 4-stage counters. The counter stages are D-TYPE flip-flops having interchangeable CLOCK and ENABLE inputs for incrementing on either the positive-going or negative-going transition. For single-unit operation the ENABLE input is maintained "high" and the counter advances on
each positive-going transition of the CLOCK. The counters are cleared by high levels on their clear lines. The counter can be cascaded in the ripple mode by connecting Q4 to the enable input of the subsequent counter while the clock input of the latter is held permanently low. All inputs are equipped with protection circuits against static discharge and transient excess voltage.
PIN CONNECTION AND IEC LOGIC SYMBOLS
July 2001
1/11
M74HC4518
INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION
PIN No 1, 9 2, 10 3, 4, 5, 6 7, 15 11, 12, 13, 14 8 16 SYMBOL 1CLOCK, 2CLOCK 1ENABLE, 2ENABLE 1Q0 to 1Q3 1CLEAR, 2CLEAR NAME AND FUNCTION Clock Inputs (LOW to HIGH, Edge-Triggered) Clock Enable Inputs Data Outputs Asynchronous Reset Inputs (Active LOW)
2Q0 tO 2Q3 Data Outputs GND Vcc Ground (0V) Positive Supply Voltage
TRUTH TABLE
INPUTS FUNCTION CLOCK ENABLE H L X X L H X
X : Don’t Care Z : High Impedance
CLEAR L L L L L L INCREMENT COUNTER INCREMENT COUNTER NO CHANGE NO CHANGE NO CHANGE NO CHANGE Q0 THRU Q3=L
X
H
LOGIC DIAGRAM
This logic diagram has not be used to estimate propagation delays
2/11
M74HC4518
TIMING CHART
ABSOLUTE MAXIMUM RATINGS
Symbol VCC VI VO IIK IOK IO Supply Voltage DC Input Voltage DC Output Voltage DC Input Diode Current DC Output Diode Current DC Output Current Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 20 ± 20 ± 25 ± 50 500(*) -65 to +150 300 Unit V V V mA mA mA mA mW °C °C
ICC or IGND DC VCC or Ground Current PD Power Dissipation Tstg TL Storage Temperature Lead Temperature (10 sec)
Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) 500mW at 65 °C; derate to 300mW by 10mW/°C from 65°C to 85°C
3/11
M74HC4518
RECOMMENDED OPERATING CONDITIONS
Symbol VCC VI VO Top tr, tf Supply Voltage Input Voltage Output Voltage Operating Temperature Input Rise and Fall Time VCC = 2.0V VCC = 4.5V VCC = 6.0V Parameter Value 2 to 6 0 to VCC 0 to VCC -55 to 125 0 to 1000 0 to 500 0 to 400 Unit V V V °C ns ns ns
DC SPECIFICATIONS
Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 4.5 6.0 VOL Low Level Output Voltage 2.0 4.5 6.0 4.5 6.0 II ICC Input Leakage Current Quiescent Supply Current 6.0 6.0 IO=-20 µA IO=-20 µA IO=-20 µA IO=-4.0 mA IO=-5.2 mA IO=20 µA IO=20 µA IO=20 µA IO=4.0 mA IO=5.2 mA VI = VCC or GND VI = VCC or GND TA = 25°C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.18 5.68 2.0 4.5 6.0 4.31 5.8 0.0 0.0 0.0 0.17 0.18 0.1 0.1 0.1 0.26 0.26 ± 0.1 4 1.9 4.4 5.9 4.13 5.63 0.1 0.1 0.1 0.37 0.37 ±1 40 Typ. Max. Value -40 to 85°C Min. 1.5 3.15 4.2 0.5 1.35 1.8 1.9 4.4 5.9 4.10 5.60 0.1 0.1 0.1 0.40 0.40 ±1 80 µA µA V V Max. -55 to 125°C Min. 1.5 3.15 4.2 0.5 1.35 1.8 Max. V Unit
VIH
High Level Input Voltage Low Level Input Voltage High Level Output Voltage
VIL
V
VOH
4/11
M74HC4518
AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns)
Test Condition Symbol Parameter VCC (V) 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 2.0 4.5 6.0 TA = 25°C Min. Typ. 30 8 7 72 22 18 65 20 16 23 51 60 25 6 5 20 5 4 21 3 3 Max. 75 15 13 160 32 27 150 30 26 4.8 24 28 75 15 13 75 15 13 50 10 9 95 19 16 95 19 16 60 12 11 Value -40 to 85°C Min. Max. 95 19 16 200 40 34 190 38 33 4 20 24 110 22 19 110 22 19 75 15 13 -55 to 125°C Min. Max. 110 22 19 240 48 41 225 45 38 ns Unit
tTLH tTHL Output Transition Time tPLH tPHL Propagation Delay Time (CK, ENABLE - Qn) tPHL Propagation Delay Time (CLR - Qn) Maximum Clock Frequency Minimum Pulse Width (CLOCK ,ENABLE) Minimum Pulse Width (CLEAR) Minimum Removal Time (CLEAR)
ns
ns
fMAX
6 30 35
MHz
tW(H) tW(L) tW(L)
ns
ns
tREM
ns
CAPACITIVE CHARACTERISTICS
Test Condition Symbol Parameter VCC (V) TA = 25°C Min. Typ. 5 38 Max. 10 Value -40 to 85°C Min. Max. 10 -55 to 125°C Min. Max. 10 pF pF Unit
CIN CPD
Input Capacitance Power Dissipation Capacitance (note 1)
1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/2 (per Counter)
5/11
M74HC4518
TEST CIRCUIT
CL = 50pF or equivalent (includes jig and probe capacitance) RT = ZOUT of pulse generator (typically 50Ω)
WAVEFORM 1: MINIMUM PULSE WIDTH AND REMOVAL TIME (f=1MHz; 50% duty cycle)
6/11
M74HC4518
WAVEFORM 2 : PROPAGATION DELAY TIME, MINIMUM PULSE WIDTH(f=1MHz; 50% duty cycle)
7/11
M74HC4518
Plastic DIP-16 (0.25) MECHANICAL DATA
mm. DIM. MIN. a1 B b b1 D E e e3 F I L Z 3.3 1.27 8.5 2.54 17.78 7.1 5.1 0.130 0.050 0.51 0.77 0.5 0.25 20 0.335 0.100 0.700 0.280 0.201 1.65 TYP MAX. MIN. 0.020 0.030 0.020 0.010 0.787 0.065 TYP. MAX. inch
P001C
8/11
M74HC4518
SO-16 MECHANICAL DATA
DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 8° (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45° (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.003 MIN. inch TYP. MAX. 0.068 0.007 0.064 0.018 0.010
PO13H
9/11
M74HC4518
TSSOP16 MECHANICAL DATA
mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0° 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8° 0.75 0° 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8° 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0089 0.201 0.260 0.176 inch
A
A2 A1 b e K c L E
D
E1
PIN 1 IDENTIFICATION
1
0080338D
10/11
M74HC4518
Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. © The ST logo is a registered trademark of STMicroelectronics © 2001 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - China - Finland - France - Germany - Hong Kong - India - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom © http://www.st.com
11/11
很抱歉,暂时无法提供与“M74HC4518”相匹配的价格&库存,您可以联系我们找货
免费人工找货