M74HC4852

M74HC4852 DUAL 4:1 CHANNEL ANALOG MUX/DEMUX WITH INJECTION CURRENT PROTECTION s s s s s s s s s LOW POWER DISSIPATION: ICC = 2µA(MAX.) at TA=25°C INJECTION CURRENT PROTECTION: V∆OUT 2000V (JESD22-A114B); MM > 200V SOP SOP-Large TSSOP ORDER CODES PACKAGE TUBE T&R M74HC4852RM13TR M74HC4852MWR M74HC4852TTR SOP M74HC4852M1R SOP-Large TSSOP DESCRIPTION The M74HC4852 is a dual four-channel analog MULTIPLEXER/DEMULTIPLEXER fabricated with silicon gate C2MOS technology. It is pin to pin compatible with the equivalent to standard HC4052 and MC14052, but features injection current effect control. This makes this device especially suited for usage in automotive applications where voltages in excess of normal PIN CONNECTION AND IEC LOGIC SYMBOLS logic voltage are common. The injection current effect control allows signals at disabled input channels to exceed the supply voltage range or go down ground without affecting the signal of the enabled analog channel. This eliminates the need for external diode-resistor networks typically used to keep the analog channel signals within the supply voltage range. This analog switch is bidirectional and digitally controlled. It has two binary control inputs A and B to select 1 of 4 to be turned on, and connected to the output, and a INH input to disable all channels. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. November 2003 1/15 M74HC4852 CONTROL INPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No SYMBOL NAME AND FUNCTION Common Output/Input INHIBIT Input Not Connected Select Inputs Independent Input/Outputs Ground (0V) Positive Supply Voltage 3, 13 YCOM, XCOM 6 INH 7 NC 10, 9 A, B 12,14,15,11, X0 to X3, 1, 5, 2, 4 Y0 to Y3 8 GND 16 VCC TRUTH TABLE I/O EQUIVALENT CIRCUIT INH L L L L H X: Don’t care INPUT STATE ON CHANNEL B L L H H X A L H L H X X0 X1 X2 X3 NONE Y0 Y1 Y2 Y3 NONE FUNCTIONAL DIAGRAM 2/15 M74HC4852 ABSOLUTE MAXIMUM RATINGS Symbol VCC VIN VI/O ICK IIOK ICC PD Tstg TL Supply Voltage Control Input Voltage Switch I/O Voltage Control Input Diode Current I/O Diode Current DC VCC or Ground Current Power Dissipation Storage Temperature Lead Temperature (10 sec) SOP TSSOP Parameter Value -0.5 to +7 -0.5 to VCC + 0.5 -0.5 to VCC + 0.5 ± 25 ± 25 ± 50 500(*) 450(*) -65 to +150 300 Unit V V V mA mA mA mW mW °C °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied (*) Power dissipation at 65 °C. Derating from 65°C to 125°C: SO Package -7mW/°C; TSSOP Package -6.1mW/°C RECOMMENDED OPERATING CONDITIONS Symbol VCC VI/O VI/O VIN Top tr, tf Supply Voltage Input Output Voltage Static or Dynamic Voltage Across Switch (note1) Control Input Voltage Operating Temperature Input Rise and Fall Time (note2) (Channel Select or Enable Inputs only) VCC = 2.0V VCC = 3.0.V VCC = 3.3V VCC = 4.5V VCC = 6.0V Parameter Value 2 to 6 0 to VCC 0 to 1.2 0 to VCC -55 to 125 0 to 1000 0 to 800 0 to 700 0 to 500 0 to 400 ns Unit V V V V °C 1) For voltage drops across switch greater than 1.2V (switch on), excessive VCC current may drawn; i.e., the current out of the switch may containbothVCC andswitchinputcomponents.Thereliability ofthedevicewillbeunaffectedunlesstheMaximumRatingsareexceeded. 2) VIN from 30% to 70% VCC of channel Selected or Enable Inputs 3/15 M74HC4852 DC SPECIFICATIONS Test Condition Symbol Parameter VCC (V) 2.0 3.0 3.0 4.5 6.0 2.0 3.0 3.3 4.5 6.0 2.0 3.0 3.3 4.5 6.0 ∆RON Difference of ON Resistance between switches 2.0 3.0 3.3 4.5 6.0 6.0 IS=2mA IS≤2mA IS=2mA IS≤2mA VIN = VIHC or VILC VIS = VCC/2 VIN = VIHC or VILC VIS = VCC to GND TA = 25°C Min. 1.5 2.1 2.3 3.15 4.2 0.5 0.9 1.0 1.35 1.8 500 215 210 160 150 4 2 2 2 3 650 280 270 210 195 10 8 8 8 9 ±0.1 Value up to 85°C up to 125°C Min. 1.5 2.1 2.3 3.15 4.2 0.5 0.9 1.0 1.35 1.8 670 320 305 240 220 15 12 12 12 13 ± 0.5 0.5 0.9 1.0 1.35 1.8 700 360 345 270 250 20 16 16 16 18 ± 1.0 Ω Ω Max. Unit Typ. Max. Min. Max. 1.5 2.1 2.3 3.15 4.2 VIHC High Level Input Voltage V VILC Low Level Input Voltage V RON ON Resistance IOFF IOFF ION IIN ICC Input/Output Leakage Current (SWITCH OFF) (Any Channel) Input/Output Leakage Current (SWITCH OFF) (Common Channel) Switch Input Leakage Current (SWITCH ON, OUTPUT OPEN) Control Input Current Quiescent Supply Current VIN = VCC or GND µA 6.0 ± 0.2 ±2 ±4 µA ±0.1 ± 0.5 ±1 µA 6.0 6.0 VIN = VCC or GND VIN = VCC or GND VIN(analog)= GND ± 0.1 2 ± 0.1 20 ±1 40 µA µA 6.0 VIN = VCC or GND 4/15 M74HC4852 AC ELECTRICAL CHARACTERISTICS (CL = 50 pF, Input tr = tf = 6ns) Test Condition Symbol Parameter VCC (V) 2.0 3.0 3.3 4.5 6.0 2.0 3.0 3.3 4.5 6.0 2.0 3.0 3.3 4.5 6.0 TEST CIRCUIT 1 TA = 25°C Min. Value up to 85°C up to 125°C Min. Max. 32 19.5 18.5 13.5 12 40 23 22 17 16.5 115 110 105 100 80 10 Unit Typ. Max. Min. Max. 19.5 12 11 8.6 8 23 13.5 12.5 10 9.5 25 15.5 14.5 11.5 10 30 17.5 16.5 13 12.5 95 90 85 80 78 10 29 17.5 16.5 12.5 11 35 20 19 15 14.5 105 100 95 90 80 10 tPHL,tPLH Propagation Delay Time, Analog Input to Analog Output ns tPHL,tPLH Propagation Delay Time Channel-Select to Analog Output ns tPHZtPZH Enable Disable tPLZ,tPZL Time, Enable or Channel-Select to Analog Output ns CIN CIN CIN CPD Input Capacitance (Digital Pins) Input Capacitance (Switches Off, Any Single Analog Pins) Input Capacitance (Switches Off, Any Common Analog Pins) Power Dissipation Capacitance (*) 3.5 pF pF 6.7 15 15 15 pF 22 3.3 5.0 24 28 40 40 40 pF (*) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/8 INJECTION CURRENT COUPLING SPECIFICATION (TA= -55°C to +125°C) Test Condition Symbol V∆OUT Parameter Shift of Output Voltage of Enabled Analog Channel VCC (V) 3.3 5.0 3.3 5.0 3.3 5.0 3.3 5.0 TEST CIRCUIT 2 IIN ≤ 1mA, RS ≤ 3.9KΩ IIN ≤ 10mA, RS ≤ 3.9KΩ IIN ≤ 1mA, RS ≤ 20KΩ IIN ≤ 10mA, RS ≤ 20KΩ Typ.(1) 0.050 0.100 0.345 0.067 0.050 0.110 0.050 0.024 Value Unit Max. 1.0 1.0 5.0 5.0 2.0 2.0 20 20 mV 1) Typical values are measured at TA=25°C e they are calculated as a difference from VOUT without Injection Current and VOUT with Injection Current. IIN = total current injected into any other disabled channel, one at time. 5/15 M74HC4852 TEST CIRCUIT 1 TEST tPLH, tPHL tPZL, tPLZ tPZH, tPHZ CL =50pF or equivalent (includes jig and probe capacitance) RL = R1 = 10KΩ or equivalent RT = ZOUT of pulse generator (typically 50Ω) SWITCH Open VCC GND TEST CIRCUIT 2 6/15 M74HC4852 WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) 7/15 M74HC4852 WAVEFORM: PROPAGATION DELAY (f=1MHz; 50% duty cycle) CHANNEL RESISTANCE (RON) ICC (Opr.) 8/15 M74HC4852 SO-16 MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 8 3.8 4.6 0.5 9.8 5.8 1.27 8.89 4.0 5.3 1.27 0.62 ˚ (max.) 0.149 0.181 0.019 10 6.2 0.35 0.19 0.5 45˚ (typ.) 0.385 0.228 0.050 0.350 0.157 0.208 0.050 0.024 0.393 0.244 0.1 mm. MIN. TYP MAX. 1.75 0.2 1.65 0.46 0.25 0.013 0.007 0.019 0.004 MIN. inch TYP. MAX. 0.068 0.008 0.064 0.018 0.010 PO13H 9/15 M74HC4852 TSSOP16 MECHANICAL DATA mm. DIM. MIN. A A1 A2 b c D E E1 e K L 0˚ 0.45 0.60 0.05 0.8 0.19 0.09 4.9 6.2 4.3 5 6.4 4.4 0.65 BSC 8˚ 0.75 0˚ 0.018 0.024 1 TYP MAX. 1.2 0.15 1.05 0.30 0.20 5.1 6.6 4.48 0.002 0.031 0.007 0.004 0.193 0.244 0.169 0.197 0.252 0.173 0.0256 BSC 8˚ 0.030 0.004 0.039 MIN. TYP. MAX. 0.047 0.006 0.041 0.012 0.0079 0.201 0.260 0.176 inch A A2 A1 b e K c L E D E1 PIN 1 IDENTIFICATION 1 0080338D 10/15 M74HC4852 SO-16L MECHANICAL DATA DIM. A a1 a2 b b1 C c1 D E e e3 F G L M S 8 0.5 1.27 0.75 ˚ (max.) 0.020 0.050 0.029 7.4 10.1 10.0 1.27 8.89 7.6 0.291 10.5 10.65 0.35 0.23 0.5 45˚ (typ.) 0.397 0.393 0.050 0.350 0.300 0.413 0.419 0.1 mm. MIN. TYP MAX. 2.65 0.2 2.45 0.49 0.32 0.014 0.009 0.020 0.004 MIN. inch TYP. MAX. 0.104 0.008 0.096 0.019 0.012 PO13I 11/15 M74HC4852 Tape & Reel SO-16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.45 10.3 2.1 3.9 7.9 12.8 20.2 60 22.4 6.65 10.5 2.3 4.1 8.1 0.254 0.406 0.082 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.262 0.414 0.090 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 12/15 M74HC4852 Tape & Reel TSSOP16 MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 6.7 5.3 1.6 3.9 7.9 12.8 20.2 60 22.4 6.9 5.5 1.8 4.1 8.1 0.264 0.209 0.063 0.153 0.311 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.272 0.217 0.071 0.161 0.319 MIN. TYP. MAX. 12.992 0.519 inch 13/15 M74HC4852 Tape & Reel SO-16L MECHANICAL DATA mm. DIM. MIN. A C D N T Ao Bo Ko Po P 10.8 10.7 2.9 3.9 11.9 12.8 20.2 60 22.4 11.0 10.9 3.1 4.1 12.1 0.425 0.421 0.114 0.153 0.468 TYP MAX. 330 13.2 0.504 0.795 2.362 0.882 0.433 0.429 0.122 0.161 0.476 MIN. TYP. MAX. 12.992 0.519 inch 14/15 M74HC4852 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics All other names are the property of their respective owners © 2003 STMicroelectronics - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 15/15