STF10P6F6

STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 P-channel -60 V, 0.13 Ω typ., -10 A STripFET™ F6 Power MOSFETs in DPAK, TO-220FP, TO-220 and IPAK packages Datasheet − production data Features TAB Order codes 3 VDS RDS(on) max ID -60 V 0.16 Ω -10 A STD10P6F6 1 3 DPAK 1 2 STF10P6F6 STP10P6F6 TO-220FP STU10P6F6 TAB TAB • Very low on-resistance • Very low gate charge 3 2 3 1 2 1 • High avalanche ruggedness IPAK TO-220 • Low gate drive power loss Figure 1. Internal schematic diagram , TAB Applications • Switching applications Description These devices are P-channel Power MOSFETs developed using the STripFET™ F6 technology, with a new trench gate structure. The resulting Power MOSFETs exhibit very low RDS(on) in all packages. AM11258v1 Table 1. Device summary Order codes Marking Package Packing DPAK Tape and reel STD10P6F6 STF10P6F6 TO-220FP 10P6F6 STP10P6F6 TO-220 STU10P6F6 IPAK July 2015 This is information on a product in full production. DocID022967 Rev 5 Tube 1/24 www.st.com Contents STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Contents 1 Electrical ratings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 2 Electrical characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 2.1 Electrical characteristics (curves) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 3 Test circuits 4 Package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5 2/24 ............................................... 9 4.1 DPAK package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 4.2 DPAK packing information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 4.3 TO-220FP package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 4.4 TO-220 package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17 4.5 IPAK package information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 Revision history . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23 DocID022967 Rev 5 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 1 Electrical ratings Electrical ratings Table 2. Absolute maximum ratings Value Symbol Parameter DPAK IPAK Unit TO-220FP TO-220 VDS Drain-source voltage -60 V VGS Gate-source voltage ± 20 V Drain current (continuous) at TC = 25 °C -10 A Drain current (continuous) at TC = 100 °C -7.2 A IDM (2) Drain current (pulsed) -40 A PTOT Total dissipation at TC = 25 °C EAS Single pulse avalanche energy (starting TJ=25 °C, ID=-3 A, VDD=40 V) VISO Insulation withstand voltage (RMS) from all three leads to external heat sink (t=1 s; TC=25 °C) VDG Drain-gate voltage (VGS = 0) Tstg Storage temperature ID (1) ID Tj 35 20 30 W 80 mJ 2500 V -20 V -55 to 175 °C 175 °C Max. operating junction temperature 1. Limited by package 2. Pulse width limited by safe operating area Table 3. Thermal data Value Symbol Parameter Unit DPAK Rthj-case Thermal resistance junction-case max Rthj-amb Thermal resistance junction-ambient max Rthj-pcb Thermal resistance junction-pcb max(1) IPAK 4.29 100 50 TO-220FP TO-220 7.5 5 °C/W 62.5 62.5 °C/W °C/W 1. When mounted on 1 inch2 FR-4, 2 Oz copper board DocID022967 Rev 5 3/24 24 Electrical characteristics 2 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Electrical characteristics (TCASE = 25 °C unless otherwise specified). Table 4. Static Symbol V(BR)DSS Parameter Test conditions Drain-source breakdown Voltage ID = -250 µA, VGS= 0 V Min. Typ. Max. -60 Unit V VDS = -60 V -1 µA VDS = -60 V, Tc = 125 °C -10 µA ±100 nA -4 V 0.13 0.16 Ω Min. Typ. Max. Unit - 340 - pF - 40 - pF - 20 - pF - 6.4 - nC - 1.7 - nC - 1.7 - nC Min. Typ. Max. Unit - 64 - ns - 5.3 - ns - 14 - ns - 3.7 - ns IDSS Zero gate voltage drain current (VGS = 0) IGSS Gate body leakage current (VDS = 0) VGS = ±20 V VGS(th) Gate threshold voltage VDS = VGS, ID = -250 µA RDS(on) Static drain-source onresistance VGS = -10 V, ID = -5 A -2 Table 5. Dynamic Symbol Parameter Ciss Input capacitance Coss Output capacitance Crss Reverse transfer capacitance Qg Total gate charge Qgs Gate-source charge Qgd Gate-drain charge Test conditions VDS = -48 V, f=1 MHz, VGS = 0 V VDD = -30 V, ID = -10 A VGS = -10 V (see Figure 16) Table 6. Switching on/off (inductive load) Symbol td(on) tr td(off) tf 4/24 Parameter Test conditions Turn-on delay time Rise time Turn-off delay time VDD = -48 V, ID = -5 A, RG = 4.7 Ω, VGS = -10 V (see Figure 15) Fall time DocID022967 Rev 5 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Electrical characteristics Table 7. Source drain diode Symbol Parameter Test conditions Min. Typ. Max. Unit Source-drain current - -10 A ISDM(1) Source-drain current (pulsed) - -40 A VSD(2) Forward on voltage ISD = -5 A, VGS = 0 V - -1.1 V trr Reverse recovery time - 20 ns Qrr Reverse recovery charge - 17.8 nC IRRM Reverse recovery current ISD = -10 A, di/dt = -100 A/µs, VDD = -48 V (see Figure 17) - -1.8 A ISD 1. Pulse width limited by safe operating area. 2. Pulsed: pulse duration = 300 µs, duty cycle 1.5% DocID022967 Rev 5 5/24 24 Electrical characteristics STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 2.1 Electrical characteristics (curves) Note: For the P-channel Power MOSFET, current and voltage polarities are reversed. Figure 2. Safe operating area for DPAK, TO-220 and IPAK Figure 3. Thermal impedance DPAK, TO-220 and IPAK AM15408v1 ID (A) 10 GIPG180420141107SA K δ=0.5 0.2 100µs is 1 th is in a ion y m at er d b p O ite Lim 0.1 1ms ea a r (on) DS R x 0.05 10 -1 10ms 0.02 Tj= 175°C Tc=25°C 0.1 pcb 0.01 Single pulse Single pulse 0.01 0.1 10 1 VDS(V) Figure 4. Safe operating area for TO-220FP AM15492v1 ID (A) 10 -2 10 -5 10 -1 10 -2 10 -3 10 -4 tp(s) Figure 5. Thermal impedance for TO-220FP AM15493v1 K δ=0.5 10 is ea ) ar S(on is th RD x in n ma o ti y ra d b e e p O mit Li 1 100µs 1ms 10 -1 0.05 0.02 10ms Tj= 175°C Tc=25°C Single pulse 0.01 Single pulse 0.1 0.1 10 1 VDS(V) Figure 6. Output characteristics 10 -4 10 -3 VGS= 10 V 10 -1 tp(s) AM15346v1 ID (A) VDS= 9 V 25 25 VGS= 6 V 20 10 -2 Figure 7. Transfer characteristics AM15340v1 ID (A) 10 -2 10 -5 20 15 15 VGS= 5 V 10 10 5 0 0 6/24 5 VGS= 4 V 5 0 10 VDS(V) DocID022967 Rev 5 2 3 4 5 6 7 8 9 10 VGS(V) STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Figure 8. Gate charge vs gate-source voltage AM15341v2 VGS (V) VDD=30V 10 ID=10A Electrical characteristics Figure 9. Static drain-source on-resistance AM15350v1 RDS(on) (mΩ) VGS=10V 180 8 160 6 140 4 120 2 0 0 2 4 Qg(nC) 6 Figure 10. Capacitance variations 100 1 2 3 4 5 6 7 8 9 ID(A) Figure 11. Normalized V(BR)DSS vs temperature C (pF) 400 AM15342v1 350 Ciss AM15349v1 V(BR)DSS (norm) 1.15 ID = 1mA 1.10 300 250 1.05 200 1 150 100 0.95 50 0 0 10 20 30 40 Coss Crss 50 VDS(V) Figure 12. Normalized gate threshold voltage vs temperature AM15344v1 VGS(th) (norm) 0.90 -55 -30 -5 20 45 70 95 120 TJ(°C) Figure 13. Normalized on-resistance vs temperature AM15350v1 RDS(on) (norm) 2 1.10 VGS=10V 1.8 ID=250 µA 1 1.6 1.4 0.90 1.2 1 0.80 0.8 0.70 0.60 -55 -30 -5 0.6 20 45 70 95 120 TJ(°C) 0.4 -55 -30 -5 DocID022967 Rev 5 20 45 70 95 120 TJ(°C) 7/24 24 Electrical characteristics STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Figure 14. Source-drain diode forward characteristics AM15345v1 VSD (V) TJ=-55°C 1.05 TJ=25°C 0.95 0.85 0.75 TJ=175°C 0.65 0.55 8/24 2 4 6 DocID022967 Rev 5 8 ISD(A) STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 3 Test circuits Test circuits Figure 15. Switching times test circuit for resistive load Figure 16. Gate charge test circuit AM11255v1 AM11256v1 Figure 17. Test circuit for diode recovery behaviour AM11257v1 DocID022967 Rev 5 9/24 24 Package information 4 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Package information In order to meet environmental requirements, ST offers these devices in different grades of ECOPACK® packages, depending on their level of environmental compliance. ECOPACK® specifications, grade definitions and product status are available at: www.st.com. ECOPACK® is an ST trademark. 4.1 DPAK package information Figure 18. DPAK (TO-252) type C package outline  “  ¡ BBW\SHB& 10/24 DocID022967 Rev 5 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Package information Table 8. DPAK (TO-252) type C package mechanical data mm Dim. Min. Typ. Max. A 2.20 2.30 2.38 A1 0.90 1.01 1.10 A2 0.00 0.10 b 0.72 0.85 b4 5.13 c 0.47 0.60 c2 0.47 0.60 D 6.00 D1 5.25 E 5.33 5.46 6.10 6.20 6.50 6.60 6.70 e 2.186 2.286 2.386 E1 4.70 H 9.80 10.10 10.40 L 1.40 1.50 1.70 L1 L2 2.90 REF 0.90 1.25 L3 L4 0.51 BSC 0.60 0.80 L6 1.00 1.80 BSC Θ1 5° 7° 9° Θ2 5° 7° 9° V2 0° 8° DocID022967 Rev 5 11/24 24 Package information STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Figure 19. DPAK (TO-252) footprint (a) )3B4 a. All dimensions are in millimeters 12/24 DocID022967 Rev 5 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 4.2 Package information DPAK packing information Figure 20. Tape for DPAK (TO-252) 10 pitches cumulative tolerance on tape +/- 0.2 mm T P0 Top cover tape P2 D E F B1 K0 For machine ref. only including draft and radii concentric around B0 W B0 A0 P1 D1 User direction of feed R Bending radius User direction of feed AM08852v1 DocID022967 Rev 5 13/24 24 Package information STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Figure 21. Reel for DPAK (TO-252) T REEL DIMENSIONS 40mm min. Access hole At sl ot location B D C N A Full radius G measured at hub Tape slot in core for tape start 25 mm min. width AM08851v2 Table 9. DPAK (TO-252) tape and reel mechanical data Tape Reel mm mm Dim. Dim. Min. Max. A0 6.8 7 A B0 10.4 10.6 B 1.5 12.1 C 12.8 1.6 D 20.2 G 16.4 50 B1 14/24 Min. Max. 330 13.2 D 1.5 D1 1.5 E 1.65 1.85 N F 7.4 7.6 T K0 2.55 2.75 P0 3.9 4.1 Base qty. 2500 P1 7.9 8.1 Bulk qty. 2500 P2 1.9 2.1 R 40 T 0.25 0.35 W 15.7 16.3 DocID022967 Rev 5 18.4 22.4 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 4.3 Package information TO-220FP package information Figure 22. TO-220FP package outline 7012510_Rev_K_B DocID022967 Rev 5 15/24 24 Package information STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Table 10. TO-220FP mechanical data mm Dim. Min. Typ. A 4.4 4.6 B 2.5 2.7 D 2.5 2.75 E 0.45 0.7 F 0.75 1 F1 1.15 1.70 F2 1.15 1.70 G 4.95 5.2 G1 2.4 2.7 H 10 10.4 L2 16/24 Max. 16 L3 28.6 30.6 L4 9.8 10.6 L5 2.9 3.6 L6 15.9 16.4 L7 9 9.3 Dia 3 3.2 DocID022967 Rev 5 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 4.4 Package information TO-220 package information Figure 23. TO-220 type A package outline BW\SH$B5HYB7 DocID022967 Rev 5 17/24 24 Package information STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Table 11. TO-220 type A mechanical data mm Dim. Min. Typ. A 4.40 4.60 b 0.61 0.88 b1 1.14 1.70 c 0.48 0.70 D 15.25 15.75 D1 18/24 Max. 1.27 E 10 10.40 e 2.40 2.70 e1 4.95 5.15 F 1.23 1.32 H1 6.20 6.60 J1 2.40 2.72 L 13 14 L1 3.50 3.93 L20 16.40 L30 28.90 ∅P 3.75 3.85 Q 2.65 2.95 DocID022967 Rev 5 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 4.5 Package information IPAK package information Figure 24. IPAK (TO-251) type A package outline 0068771_L DocID022967 Rev 5 19/24 24 Package information STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Table 12. IPAK (TO-251) type A mechanical data mm. DIM min. typ. A 2.20 2.40 A1 0.90 1.10 b 0.64 0.90 b2 b4 0.95 5.20 B5 5.40 0.30 c 0.45 0.60 c2 0.48 0.60 D 6.00 6.20 E 6.40 6.60 e e1 2.28 4.40 H 20/24 max. 4.60 16.10 L 9.00 9.40 L1 0.80 1.20 L2 0.80 V1 10° DocID022967 Rev 5 1.00 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Package information Figure 25. IPAK (TO-251) type C package outline 7\SH&5HY/ DocID022967 Rev 5 21/24 24 Package information STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 Table 13. IPAK (TO-251) type C mechanical data mm Dim. min. typ. max. A 2.20 2.30 2.35 A1 0.90 1.00 1.10 b 0.66 0.79 b2 22/24 0.90 b4 5.23 c 0.46 0.59 c2 0.46 0.59 D 6.00 6.10 6.20 D1 5.20 5.37 5.55 E 6.50 6.60 6.70 E1 4.60 4.78 4.95 e 2.20 2.25 2.30 e1 4.40 4.50 4.60 H 16.18 16.48 16.78 L 9.00 9.30 9.60 L1 0.80 1.00 1.20 L2 0.90 1.08 1.25 θ1 3° 5° 7° θ2 1° 3° 5° DocID022967 Rev 5 5.33 5.43 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 5 Revision history Revision history Table 14. Document revision history Date Revision 10-May-2012 1 First release. 20-Jun-2012 2 Updated title on the cover page. Updated all parameter values in Table 5, Table 6 and Figure 1. 3 – Added: TO-220FP and IPAK packages – Updated: RDS(on) value in cover page, Rthj-case values, Table 5, 6 and 7 typical values – Updated mechanical data only for DPAK in Section 4: Package information 4 – Updated: Figure 2 and 3 – Updated: Section 4.1: DPAK package information and Section 4.4: TO-220 package information – Minor text changes 5 – – – – 17-May-2013 24-Apr-2014 27-Jul-2015 Changes All voltage and current polarities inverted Added: note in Section 2.1: Electrical characteristics (curves) Updated: Section 4.1 and Section 4.5 Text and formatting changes throughout document DocID022967 Rev 5 23/24 24 STD10P6F6, STF10P6F6, STP10P6F6, STU10P6F6 IMPORTANT NOTICE – PLEASE READ CAREFULLY STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, enhancements, modifications, and improvements to ST products and/or to this document at any time without notice. Purchasers should obtain the latest relevant information on ST products before placing orders. ST products are sold pursuant to ST’s terms and conditions of sale in place at the time of order acknowledgement. Purchasers are solely responsible for the choice, selection, and use of ST products and ST assumes no liability for application assistance or the design of Purchasers’ products. No license, express or implied, to any intellectual property right is granted by ST herein. Resale of ST products with provisions different from the information set forth herein shall void any warranty granted by ST for such product. ST and the ST logo are trademarks of ST. All other product or service names are the property of their respective owners. Information in this document supersedes and replaces information previously supplied in any prior versions of this document. © 2015 STMicroelectronics – All rights reserved 24/24 DocID022967 Rev 5