TSOP14533

TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. www.vishay.com Vishay Semiconductors IR Receiver Modules for Remote Control Systems FEATURES • Improved dark sensitivity • Improved immunity against optical noise • Improved immunity against Wi-Fi noise • Low supply current • Photo detector and preamplifier in one package • Internal filter for PCM frequency • Supply voltage: 2.5 V to 5.5 V 1 2 • Insensitive to supply voltage ripple and noise 3 16672 • Material categorization: for definitions of compliance please see www.vishay.com/doc?99912 LINKS TO ADDITIONAL RESOURCES 3D 3D Product Page 3D Models Calculators Marking MECHANICAL DATA Packages Pinning for TSOP14...: 1 = OUT, 2 = GND, 3 = VS Holders Bends and Cuts Pinning for TSOP12...: 1 = OUT, 2 = VS, 3 = GND DESCRIPTION The TSOP12... and TSOP14... series devices are the latest generation miniaturized IR receiver modules for infrared remote control systems. These series provide improvements in sensitivity to remote control signals in dark ambient as well as in sensitivity in the presence of optical disturbances e.g. from CFLs. The robustness against spurious pulses originating from Wi-Fi signals has been enhanced. ORDERING CODE TSOP12..., TSOP14... - 2160 pieces in tubes BLOCK DIAGRAM VS 30 kΩ The devices contain a PIN diode and a preamplifier assembled on a lead frame. The epoxy package contains an IR filter. The demodulated output signal can be directly connected to a microprocessor for decoding. OUT Input The TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., and TSOP145.. series devices are designed to receive short burst codes (6 or more carrier cycles per burst). The third digit designates the AGC level (AGC1, AGC3, or AGC5) and the last two digits designate the band-pass frequency (see table below). The higher the AGC, the better noise is suppressed, but the lower the code compatibility. AGC1 provides basic noise suppression, AGC3 provides enhanced noise suppression and AGC5 provides maximized noise suppression. Generally, we advise to select the highest AGC that satisfactorily receives the desired remote code. Band pass AGC Demodulator GND PIN Control circuit 16833-22 APPLICATION CIRCUIT 17170-11 These components have not been qualified to automotive specifications. R1 IR receiver VS Circuit Transmitter with TSALxxxx + VS C1 μC OUT GND VO GND R1 and C1 recommended to reduce supply ripple for VS < 2.8 V Rev. 1.7, 14-Dec-2021 1 Document Number: 82804 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. www.vishay.com Vishay Semiconductors PARTS TABLE BASIC NOISE SUPPRESSION (AGC1) AGC Carrier frequency ENHANCED NOISE SUPPRESSION (AGC3) MAXIMIZED NOISE SUPPRESSION (AGC5) 30 kHz TSOP14130 TSOP12130 TSOP14330 TSOP12330 TSOP14530 TSOP12530 33 kHz TSOP14133 TSOP12133 TSOP14333 TSOP12333 TSOP14533 TSOP12533 36 kHz TSOP14136 TSOP12136 TSOP14336 (1) TSOP12336 (1) TSOP14536 TSOP12536 TSOP12338 (2)(4) 38 kHz TSOP14138 TSOP12138 TSOP14338 (2)(4) TSOP14538 TSOP12538 40 kHz TSOP14140 TSOP12140 TSOP14340 TSOP12340 TSOP14540 TSOP12540 56 kHz TSOP14156 TSOP12156 TSOP14356 (3) TSOP12356 (3) TSOP14556 TSOP12556 Package Pinning Mold 1 = OUT, 1 = OUT, 2 = VS, 2 = GND, 3 = VS 3 = GND 1 = OUT, 2 = GND, 3 = VS Dimensions (mm) 1 = OUT, 1 = OUT, 2 = VS, 2 = GND, 3 = VS 3 = GND 6.0 W x 6.95 H x 5.6 D Mounting Leaded Application Remote control (1) Best choice for Special options 1 = OUT, 2 = VS, 3 = GND RCMM (2) RECS-80 Code (3) r-map (4) XMP-1, XMP-2 • Narrow optical filter: www.vishay.com/doc?81590 • Wide optical filter: www.vishay.com/doc?82726 ABSOLUTE MAXIMUM RATINGS PARAMETER TEST CONDITION SYMBOL VALUE Supply voltage VS -0.3 to +6 V Supply current IS 3 mA Output voltage VO -0.3 to (VS + 0.3) V Output current IO 5 mA Junction temperature UNIT Tj 100 °C Storage temperature range Tstg -25 to +85 °C Operating temperature range Tamb -25 to +85 °C Tamb ≤ 85 °C Ptot 10 mW t ≤ 10 s, 1 mm from case Tsd 260 °C Power consumption Soldering temperature Note • Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability ELECTRICAL AND OPTICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) PARAMETER TEST CONDITION SYMBOL MIN. TYP. MAX. UNIT Ev = 0, VS = 3.3 V ISD 0.55 0.7 0.9 mA Ev = 40 klx, sunlight ISH - 0.8 - mA VS 2.5 - 5.5 V Transmission distance Ev = 0, test signal see Fig. 1, IR diode TSAL6200, IF = 50 mA d - 30 - m Output voltage low IOSL = 0.5 mA, Ee = 0.7 mW/m2, test signal see Fig. 1 VOSL - - 100 mV Minimum irradiance Pulse width tolerance: tpi - 3.0/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee min. - 0.08 0.15 mW/m2 Maximum irradiance tpi - 3.0/f0 < tpo < tpi + 3.5/f0, test signal see Fig. 1 Ee max. 30 - - W/m2 tpi - 3.0/fo < tpo < tpi + 3.5/fo, test signal see Fig. 1, dark ambient, burst length > 30 cycles Ee max. 0.5 - - W/m2 Angle of half transmission distance ϕ1/2 - ± 45 - ° Supply current Supply voltage Maximum long burst irradiance (AGC3, AGC5) Directivity Rev. 1.7, 14-Dec-2021 2 Document Number: 82804 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. www.vishay.com Vishay Semiconductors TYPICAL CHARACTERISTICS (Tamb = 25 °C, unless otherwise specified) Optical Test Signal (IR diode TSAL6200, IF = 0.1 A, N = 6 pulses, f = f0, T = 10 ms) Axis Title T (1) tpi ≥ 6/f0 Output Signal VO (2) (3) VOH 4/f0 < td < 10/f0 tpi - 3.0/f0 < tpo < tpi + 3.5/f0 ton 0.7 0.6 1000 0.5 toff 1st line 2nd line t tpi (1) 10000 0.8 2nd line ton, toff - Output Pulse Width (ms) Ee 0.4 0.3 100 0.2 0.1 λ = 950 nm, optical test signal, Fig. 3 0 VOL td (2) 0.1 t tpo (3) 1 10 100 1000 10 10 000 Ee - Irradiance (mW/m2) 14337-3 Fig. 4 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 1 - Output Delay and Pulse-Width Axis Title Axis Title 10000 0.30 10000 1.2 1000 0.15 1st line 2nd line 0.20 Input burst length 100 0.10 0.05 λ = 950 nm, optical test signal, Fig. 1 10 100 000 0 0.1 1000 1000 0.8 AGC3, AGC5 AGC1 0.6 100 0.4 f = f0 ± 5 % 0.2 AGC1: ∆f (3 dB) = f0/7 AGC3, AGC5: ∆f (3 dB) = f0/10 10 0 0.7 0.9 1.1 1.3 Ee - Irradiance (mW/m2) f/f0 - Relative Frequency Fig. 2 - Pulse-Width vs. Irradiance in Dark Ambient Fig. 5 - Frequency Dependence of Responsivity Axis Title Optical Test Signal 600 µs t 600 µs 94 8134 Output Signal, (see Fig. 4) VOH VOL t on t off Correlation with ambient light sources: 10 W/m2 = 1.4 klx (std. ilum. A, T = 2855 K) 10 W/m2 = 8.2 klx (daylight, T = 5900 K) 2 Wavelength of ambient illumination: λ = 950 nm 1000 100 1 0 0.01 t 10 0.1 1 10 100 Ee - Ambient DC Irradiance (W/m2) Fig. 6 - Sensitivity in Bright Ambient Fig. 3 - Test Signal Rev. 1.7, 14-Dec-2021 10000 3 t = 60 ms VO 1.0 1st line 2nd line Ee 10 2nd line Ee min. - Threshold Irradiance (mW/m2) 2nd line tpo - Output Pulse Width (ms) 0.25 1st line 2nd line 2nd line Ee min./Ee - Relative Responsivity Output pulse width 3 Document Number: 82804 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. www.vishay.com Vishay Semiconductors Axis Title Axis Title 10000 0.7 0.6 1000 0.5 f = f0 f = 30 kHz f = 10 kHz f = 100 Hz 0.4 0.3 100 0.2 0.1 10 1000 0 1 10 100 10000 0.9 0.8 0.7 1000 0.6 1st line 2nd line 2nd line S(λ)rel. - Relative Spectral Sensitivity 1.0 1st line 2nd line 0.5 0.4 100 0.3 0.2 0.1 0 750 850 950 λ - Wavelength (nm) Fig. 7 - Sensitivity vs. Supply Voltage Disturbances Fig. 10 - Relative Spectral Sensitivity vs. Wavelength Axis Title Axis0° Title 10° 20° 30° 10000 f = 38 kHz, Ee = 2 mW/m2 0.9 0.8 0.7 0.5 0.4 0.3 2nd line 2nd line 0.6 40° 1.0 1000 TSOP141.., TSOP121.. 1st line 2nd line 2nd line Maximum Envelope Duty Cycle 10 1150 ∆VS RMS - AC Voltage on DC Supply Voltage (mV) 1.0 0.9 50° 0.8 60° 100 TSOP143.., TSOP123.. 70° 0.7 0.2 0.1 80° TSOP145.., TSOP125.. 10 0 0 20 40 60 80 100 120 0.6 140 0.4 0.2 0 0.2 0.4 Burst Length (Number of Cycles/Burst) drel. - Relative Transmission Distance Fig. 8 - Maximum Envelope Duty Cycle vs. Burst Length Fig. 11 - Directivity Axis Title 0.20 0.15 1st line 2nd line 1000 0.10 100 0.05 10 0 -10 10 30 50 70 10000 0.15 1000 1st line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 10000 -30 0.6 Axis Title 0.20 2nd line Ee min. - Threshold Irradiance (mW/m2) 1050 2nd line 2nd line 2nd line Ee min. - Threshold Irradiance (mW/m2) 0.8 0.10 100 0.05 10 0 90 1.5 2.5 3.5 4.5 5.5 Tamb - Ambient Temperature (°C) VS - Supply Voltage (V) Fig. 9 - Sensitivity vs. Ambient Temperature Fig. 12 - Sensitivity vs. Supply Voltage Rev. 1.7, 14-Dec-2021 4 Document Number: 82804 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. www.vishay.com Vishay Semiconductors SUITABLE DATA FORMAT Axis Title This series is designed to suppress spurious output pulses due to noise or disturbance signals. The devices can distinguish data signals from noise due to differences in frequency, burst length, and envelope duty cycle. The data signal should be close to the device’s band-pass center frequency (e.g. 38 kHz) and fulfill the conditions in the table below. 10000 7 When a data signal is applied to the product in the presence of a disturbance, the sensitivity of the receiver is automatically reduced by the AGC to insure that no spurious pulses are present at the receiver’s output. Some examples which are suppressed are: 5 1000 1st line 2nd line 2nd line IR Signal Amplitude 6 4 3 100 2 1 • DC light (e.g. from tungsten bulbs sunlight) 10 0 0 • Continuous signals at any frequency 5 15 20 Time (ms) 16920 • Strongly or weakly modulated patterns from fluorescent lamps with electronic ballasts (see Fig. 13 or Fig. 14). 10 Fig. 13 - IR Emission from Fluorescent Lamp With Low Modulation • 2.4 GHz and 5 GHz Wi-Fi Axis Title 10000 40 1000 0 1st line 2nd line 2nd line IR Signal Amplitude 20 -20 100 -40 10 -60 0 5 10 15 20 Time (ms) 16921 Fig. 14 - IR Emission from Fluorescent Lamp With High Modulation TSOP121.., TSOP141.. TSOP123.., TSOP143.. TSOP125.., TSOP145.. Minimum burst length 6 cycles/burst 6 cycles/burst 6 cycles/burst After each burst of length A gap time is required of 6 to 70 cycles ≥ 10 cycles 6 to 35 cycles ≥ 10 cycles 6 to 24 cycles ≥ 10 cycles 70 cycles 35 cycles 24 cycles For bursts greater than a minimum gap time in the data stream is needed of > 1 x burst length > 6 x burst length > 25 ms Maximum number of continuous short bursts/second 1800 2800 1800 RCMM code Yes Preferred Yes XMP-1 code Yes Preferred Yes r-map code Yes Preferred Yes Fig. 13 Fig. 13 and Fig. 14 Fig. 13 and Fig. 14 Suppression of interference from fluorescent lamps Note • For data formats with long bursts (more than 10 carrier cycles) please see the datasheet for TSOP122.., TSOP124.., TSOP126.., TSOP142.., TSOP144.., TSOP146.. Rev. 1.7, 14-Dec-2021 5 Document Number: 82804 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 TSOP121.., TSOP123.., TSOP125.., TSOP141.., TSOP143.., TSOP145.. www.vishay.com Vishay Semiconductors PACKAGE DIMENSIONS in millimeters 3.9 1 1 30.5 ± 0.5 (5.55) 8.25 6.95 5.3 6 0.85 max. 0.89 0.5 max. 2.54 nom. 1.3 0.7 max. 4.1 2.54 nom. 5.6 marking area Not indicated tolerances ± 0.2 technical drawings according to DIN specifications R 2.5 Drawing-No.: 6.550-5169.01-4 Issue: 9; 03.11.10 13655 Rev. 1.7, 14-Dec-2021 6 Document Number: 82804 THIS DOCUMENT IS SUBJECT TO CHANGE WITHOUT NOTICE. THE PRODUCTS DESCRIBED HEREIN AND THIS DOCUMENT ARE SUBJECT TO SPECIFIC DISCLAIMERS, SET FORTH AT www.vishay.com/doc?91000 Legal Disclaimer Notice www.vishay.com Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay's knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer's responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and / or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer's technical experts. Product specifications do not expand or otherwise modify Vishay's terms and conditions of purchase, including but not limited to the warranty expressed therein. Hyperlinks included in this datasheet may direct users to third-party websites. These links are provided as a convenience and for informational purposes only. Inclusion of these hyperlinks does not constitute an endorsement or an approval by Vishay of any of the products, services or opinions of the corporation, organization or individual associated with the third-party website. Vishay disclaims any and all liability and bears no responsibility for the accuracy, legality or content of the third-party website or for that of subsequent links. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. © 2021 VISHAY INTERTECHNOLOGY, INC. ALL RIGHTS RESERVED Revision: 09-Jul-2021 1 Document Number: 91000