TC74VHC74FK

TC74VHC74F/FN/FT/FK TOSHIBA CMOS Digital Integrated Circuit Silicon Monolithic TC74VHC74F,TC74VHC74FN,TC74VHC74FT,TC74VHC74FK Dual D-Type Flip-Flop with Preset and Clear The TC74VHC74 is an advanced high speed CMOS D-FLIP FLOP fabricated with silicon gate C2MOS technology. It achieves the high speed operation similar to equivalent Bipolar Schottky TTL while maintaining the CMOS low power dissipation. The signal level applied to the D INPUT is transferred to Q OUTPUT during the positive going transition of the CK pulse. CLR and PR are independent of the CK and are accomplished by setting the appropriate input low. An input protection circuit ensures that 0 to 5.5 V can be applied to the input pins without regard to the supply voltage. This device can be used to interface 5 V to 3 V systems and two supply systems such as battery back up. This circuit prevents device destruction due to mismatched supply and input voltages. Note: The JEDEC SOP (FN) is not available in Japan. TC74VHC74F TC74VHC74FN Features • • • • • • • High speed: fmax = 170 MHz (typ.) at VCC = 5 V Low power dissipation: ICC = 2 μA (max) at Ta = 25°C High noise immunity: VNIH = VNIL = 28% VCC (min) Power down protection is provided on all inputs. Balanced propagation delays: tpLH ∼ tpHL − Wide operating voltage range: VCC (opr) = 2 V to 5.5 V Pin and function compatible with 74ALS74 TC74VHC74FT TC74VHC74FK Weight SOP14-P-300-1.27A SOL14-P-150-1.27 TSSOP14-P-0044-0.65A VSSOP14-P-0030-0.50 : 0.18 g (typ.) : 0.12 g (typ.) : 0.06 g (typ.) : 0.02 g (typ.) 1 2007-10-01 TC74VHC74F/FN/FT/FK Pin Assignment IEC Logic Symbol 1PR 1CK 1D 1CLR 2PR 2CK 2D 2CLR (4) (3) (2) (1) (10) (11) (12) (13) S C1 1D R (5) (6) (9) (8) 1CLR 1D 1CK 1PR 1 2 3 4 5 6 7 (top view) CK Q D Q CK Q D Q 14 13 12 11 10 9 8 VCC 1Q 2CLR 2D 2CK 2PR 2Q 1Q 2Q 2Q 1Q 1Q GND 2Q Truth Table Inputs Outputs CLR L H L H H H PR H L L H H H D X X X L H X CK X X X Q L H H L H Qn Q H L H H L Qn Function Clear Preset ― ― ― No Change X: Don’t care Absolute Maximum Ratings (Note) Characteristics Supply voltage range DC input voltage DC output voltage Input diode current Output diode current DC output current DC VCC/ground current Power dissipation Storage temperature Symbol VCC VIN VOUT IIK IOK IOUT ICC PD Tstg Rating −0.5 to 7.0 −0.5 to 7.0 −0.5 to VCC + 0.5 −20 ±20 ±25 ±50 180 −65 to 150 Unit V V V mA mA mA mA mW °C Note: Exceeding any of the absolute maximum ratings, even briefly, lead to deterioration in IC performance or even destruction. Using continuously under heavy loads (e.g. the application of high temperature/current/voltage and the significant change in temperature, etc.) may cause this product to decrease in the reliability significantly even if the operating conditions (i.e. operating temperature/current/voltage, etc.) are within the absolute maximum ratings and the operating ranges. Please design the appropriate reliability upon reviewing the Toshiba Semiconductor Reliability Handbook (“Handling Precautions”/“Derating Concept and Methods”) and individual reliability data (i.e. reliability test report and estimated failure rate, etc). 2 2007-10-01 TC74VHC74F/FN/FT/FK Operating Ranges (Note) Characteristics Supply voltage Input voltage Output voltage Operating temperature Input rise and fall time Symbol VCC VIN VOUT Topr dt/dv Rating 2.0 to 5.5 0 to 5.5 0 to VCC −40 to 85 0 to 100 (VCC = 3.3 ± 0.3 V) 0 to 20 (VCC = 5 ± 0.5 V) Unit V V V °C ns/V Note: The operating ranges must be maintained to ensure the normal operation of the device. Unused inputs must be tied to either VCC or GND. Electrical Characteristics DC Characteristics Characteristics Symbol Test Condition VCC (V) High-level input voltage 2.0 VIH ― 3.0 to 5.5 2.0 VIL ― 3.0 to 5.5 2.0 High-level output voltage VIN = VIH or VIL IOH = −50 μA 3.0 4.5 IOH = −4 mA IOH = −8 mA 3.0 4.5 2.0 Low-level output voltage VIN = VIH or VIL IOL = 50 μA 3.0 4.5 IOL = 4 mA IOL = 8 mA Input leakage current Quiescent supply current IIN ICC VIN = 5.5 V or GND VIN = VCC or GND 3.0 4.5 0 to 5.5 5.5 Min 1.50 VCC × 0.7 ― ― 1.9 2.9 4.4 2.58 3.94 ― ― ― ― ― ― ― Ta = 25°C Typ. ― ― ― ― 2.0 3.0 4.5 ― ― 0.0 0.0 0.0 ― ― ― ― Max ― ― 0.50 VCC × 0.3 ― ― ― ― ― 0.1 0.1 0.1 0.36 0.36 ±0.1 2.0 Ta = −40 to 85°C Min 1.50 VCC × 0.7 ― ― 1.9 2.9 4.4 2.48 3.80 ― ― ― ― ― ― ― Max ― ― 0.50 VCC × 0.3 ― ― ― ― ― 0.1 0.1 0.1 0.44 0.44 ±1.0 20.0 μA μA V V V V Unit Low-level input voltage VOH VOL 3 2007-10-01 TC74VHC74F/FN/FT/FK Timing Requirements (input: tr = tf = 3 ns) Characteristics Symbol Test Condition VCC (V) Minimum pulse width (CK) Minimum pulse width ( CLR , PR ) Minimum set-up time tw (L) tw (H) tw (L) ― 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 3.3 ± 0.3 5.0 ± 0.5 Ta = 25°C Limit 6.0 5.0 6.0 5.0 6.0 5.0 0.5 0.5 5.0 3.0 Ta = −40 to 85°C Limit 7.0 5.0 7.0 5.0 7.0 5.0 0.5 0.5 5.0 3.0 ns Unit ― ns ts ― ns Minimum hold time Minimum removal time ( CLR , PR ) th ― ns trem ― ns AC Characteristics (input: tr = tf = 3 ns) Characteristics Symbol Test Condition VCC (V) Propagation delay time (CK-Q, Q ) 3.3 ± 0.3 ― 5.0 ± 0.5 CL (pF) 15 50 15 50 15 50 15 50 15 50 15 50 Min ― ― ― ― ― ― ― ― 80 50 130 90 ― (Note) ― Ta = 25°C Typ. 6.7 9.2 4.6 6.1 7.6 10.1 4.8 6.3 125 75 170 115 4 25 Max 11.9 15.4 7.3 9.3 12.3 15.8 7.7 9.7 ― ― ― ― 10 ― Ta = −40 to 85°C Min 1.0 1.0 1.0 1.0 1.0 1.0 1.0 1.0 70 45 110 75 ― ― Max 14.0 17.5 8.5 10.5 14.5 18.0 9.0 11.0 ― ― ― ― 10 ― pF pF MHz ns ns Unit tpLH tpHL Propagation delay time ( CLR , PR -Q, Q ) tpLH tpHL 3.3 ± 0.3 ― 5.0 ± 0.5 3.3 ± 0.3 Maximum clock frequency fmax ― 5.0 ± 0.5 Input capacitance Power dissipation capacitance CIN CPD ― Note: CPD is defined as the value of the internal equivalent capacitance which is calculated from the operating current consumption without load. Average operating current can be obtained by the equation: ICC (opr) = CPD·VCC·fIN + ICC/2 (per F/F) 4 2007-10-01 TC74VHC74F/FN/FT/FK Input Equivalent Circuit INPUT 5 2007-10-01 TC74VHC74F/FN/FT/FK Package Dimensions Weight: 0.18 g (typ.) 6 2007-10-01 TC74VHC74F/FN/FT/FK Package Dimensions (Note) Note: This package is not available in Japan. Weight: 0.12 g (typ.) 7 2007-10-01 TC74VHC74F/FN/FT/FK Package Dimensions Weight: 0.06 g (typ.) 8 2007-10-01 TC74VHC74F/FN/FT/FK Package Dimensions Weight: 0.02 g (typ.) 9 2007-10-01 TC74VHC74F/FN/FT/FK RESTRICTIONS ON PRODUCT USE • The information contained herein is subject to change without notice. 20070701-EN GENERAL • TOSHIBA is continually working to improve the quality and reliability of its products. Nevertheless, semiconductor devices in general can malfunction or fail due to their inherent electrical sensitivity and vulnerability to physical stress. It is the responsibility of the buyer, when utilizing TOSHIBA products, to comply with the standards of safety in making a safe design for the entire system, and to avoid situations in which a malfunction or failure of such TOSHIBA products could cause loss of human life, bodily injury or damage to property. In developing your designs, please ensure that TOSHIBA products are used within specified operating ranges as set forth in the most recent TOSHIBA products specifications. Also, please keep in mind the precautions and conditions set forth in the “Handling Guide for Semiconductor Devices,” or “TOSHIBA Semiconductor Reliability Handbook” etc. • The TOSHIBA products listed in this document are intended for usage in general electronics applications (computer, personal equipment, office equipment, measuring equipment, industrial robotics, domestic appliances, etc.).These TOSHIBA products are neither intended nor warranted for usage in equipment that requires extraordinarily high quality and/or reliability or a malfunction or failure of which may cause loss of human life or bodily injury (“Unintended Usage”). Unintended Usage include atomic energy control instruments, airplane or spaceship instruments, transportation instruments, traffic signal instruments, combustion control instruments, medical instruments, all types of safety devices, etc.. Unintended Usage of TOSHIBA products listed in his document shall be made at the customer’s own risk. • The products described in this document shall not be used or embedded to any downstream products of which manufacture, use and/or sale are prohibited under any applicable laws and regulations. • The information contained herein is presented only as a guide for the applications of our products. No responsibility is assumed by TOSHIBA for any infringements of patents or other rights of the third parties which may result from its use. No license is granted by implication or otherwise under any patents or other rights of TOSHIBA or the third parties. • Please contact your sales representative for product-by-product details in this document regarding RoHS compatibility. Please use these products in this document in compliance with all applicable laws and regulations that regulate the inclusion or use of controlled substances. Toshiba assumes no liability for damage or losses occurring as a result of noncompliance with applicable laws and regulations. 10 2007-10-01