TME1215S

DC/DC Converters TME Series,  Watt RoHS compliant Features ◆ Single-in-Line Package (SIP) ◆ I/O-Isolation ‘000 VDC ◆ High Efficiency up to 80% ◆ Operating Temperature –40°C to +85°C ◆ Industry Standard Pinout ◆ 00% Burn-in (8 h) ◆ Lead free Design, RoHS compliant ◆ 3 Year Product Warranty The TME series is a range of sub-miniature, isolated DC/DC-converters in a SIPpackage, which requires only 0.7 cm2 of board space. They provide a cost effective solution to generate supplementary, isolated voltages. Full SMD-design and a 100% production test of parameters ensure a high reliability of this product. Models Ordercode TME 0505S TME 0509S TME 052S TME 055S TME 205S TME 209S TME 22S TME 25S TME 2405S TME 2409S TME 242S TME 245S 24 VDC ±0% 2 VDC ±0% 5 VDC ±0% Input voltage Output voltage 5 VDC 9 VDC 12 VDC 15 VDC 5 VDC 9 VDC 12 VDC 15 VDC 5 VDC 9 VDC 12 VDC 15 VDC Output current max. 200 mA 110 mA 80 mA 65 mA 200 mA 110 mA 80 mA 65 mA 200 mA 110 mA 80 mA 65 mA Efficiency typ. 70 % 76 % 77 % 78 % 71 % 77 % 79 % 80 % 70 % 76 % 79 % 79 % http://www.tracopower.com Page  of 3 DC/DC Converters TME Series Input Specifications Input current no load /full load 5 Vin models 30 mA / 290 mA typ. 12 Vin models 15 mA / 120 mA typ. 24 Vin models 10 mA / 60 mA typ. 5 Vin models 9 V max. 12 Vin models 18 V max. 24 Vin models 30 V max. 0.3 A max. can be reduced by ext. 1–3.3 µF polyester film capacitor Internal capacitors ±3% – Input variation – Load variation 20 – 100 % 1.2 % / 1 % change Vin 10 % max. 150 mV pk-pk max. ± 0.02 % / K limited 1 sec. max. 33 µF max. – Operating – Case temperature – Storage –40 °C ... +85 °C +95 °C max. –40 °C ... +105 °C 95 % rel H max. >2’000’000 h @ 25 °C 1‘000 VDC 60 pF typ. >1‘000 Mohm 90 kHz typ. (Frequency modulation) ± 30 % max. Input/Output Input/Output Input/Output  Watt Surge voltage (1 sec. max.) Reverse voltage protection Reflected input ripple current Input filter Output Specifications Voltage set accuracy Regulation Ripple and noise (20 MHz Bandwidth) Temperature coefficient Short circuit protection Capacitive load General Specifications Temperature ranges Humidity (non condensing) Reliability, calculated MTBF ( MIL-HDBK-217E) Isolation voltage (60 sec.) Isolation capacity Isolation resistance Switching frequency Frequency change over line and load All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TME Series Physical Specifications Case material Package weight Soldering temperature non conductive black plastic (UL 94-V0 rated) 5 Vin & 12 Vin models 1.3 g (0.05 oz) 24 Vin models 1.7 g (0.06 oz) max. 265°C / 10 sec  Watt Outline Dimensions mm (inches) Pin-Out 10.2 (0.4) Pin  2 3 4 Single –Vin (GND) +Vin (Vcc) –Vout +Vout 0.5 (0.02) (0.02) 0.5 1.9 ±0.5 (0.08 ±0.02) 2.54 2.54 2.54 (0.1) (0.1) (0.1) 11.5 (0.45) 3.2(0.13) 0.5 (0.02) 4.2 (0.17) 1.8 (0.07) 0.25 (0.01) Bottom view 0.5 (0.02) Tolerances ±0.25 (0.01) pins ±0.05 (0.002) Specifications can be changed any time without notice Rev. 10/05.1 Jenatschstrasse 1 · CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com 5.2 (0.2) 1 2 3 4 7.0 (0.28) 24 V Models 6.0 (0.24) Page 3 of 3