HS2D

HS2A - HS2M 2.0 AMPS. High Efficient Surface Mount Rectifiers SMB/DO-214AA .083(2.10) .077(1.95) .147(3.73) .137(3.48) Features G lass passivated junction chip. F or surface mounted application L ow forward voltage drop L ow profile package B uilt-in stain relief, ideal for automatic placement F ast switching for high efficiency H igh temperature soldering: o 260 C/10 seconds at terminals P lastic material used carries Underwriters Laboratory Classification 94V0 .187(4.75) .167(4.25) .012(.31) .006(.15) .103(2.61) .078(1.99) .012(.31) .006(.15) .056(1.41) .035(0.90) .209(5.30) .201(5.10) .008(.20) .004(.10) M echanical Data C ases: Molded plastic T erminals: P ure tin plated, lead free P olarity: Indicated by cathode band P acking: 12mm tape per EIA STD RS-481 W eight: 0.093 gram Dimensions in inches and (millimeters) M aximum Ratings and Electrical Characteristics R ating at 25 oC ambient temperature unless otherwise specified. Single phase, half wave, 60 Hz, resistive or inductive load. For capacitive load, derate current by 20% T ype Number M aximum Recurrent Peak Reverse Voltage M aximum RMS Voltage M aximum DC Blocking Voltage M aximum Average Forward Rectified Current See Fig. 1 P eak Forward Surge Current, 8.3 ms Single Half Sine-wave Superimposed on Rated Load (JEDEC method ) M aximum Instantaneous Forward Voltage @ 2.0A M aximum DC Reverse Current @ T A = 25 oC at Rated DC Blocking Voltage @ T A=125 oC M aximum Reverse Recovery Time ( Note 1 ) T ypical Junction Capacitance ( Note 2 ) M aximum Thermal Resistance (Note 3) Operating Temperature Range S ymbol H S 2A HS 2B HS 2D HS 2F HS 2G HS 2J HS 2K HS 2M U nits V V V A A V RRM V RMS V DC I(AV) IFSM VF IR Trr Cj R θJA TJ 50 35 50 400 200 300 400 600 800 1000 70 140 210 280 420 560 700 100 200 300 400 600 800 1000 2.0 50 1 .0 1.3 5 .0 150 50 50 75 30 1.7 V uA uA nS pF o C/W o C o C 80 -55 to +150 -55 to +150 S torage Temperature Range T STG 1. Reverse Recovery Test Conditions: IF =0.5A, IR =1.0A, IRR =0.25A N otes: 2. Measured at 1 MHz and Applied V R =4.0 Volts. 3.Mounted on P.C.Board with 0.4” x 0.4” (10mm x 10mm) Copper Pad Area. Version: A06 RATINGS AND CHARACTERISTIC CURVES (HS2A THRU HS2M) FIG.1- MAXIMUM FORWARD CURRENT DERATING CURVE FIG.2- TYPICAL REVERSE CHARACTERISTICS 1000 3.0 AVERAGE FORWARD CURRENT. (A) 2.5 INSTANTANEOUS REVERSE CURRENT. ( A) 2.0 100 Tj=100 0C 1.5 1.0 0.5 0 10 Tj=25 0C 0 25 50 75 100 O 125 150 175 LEAD TEMPERATURE. ( C) 1 FIG.3- MAXIMUM NON-REPETITIVE FORWARD SURGE CURRENT 70 PEAK FORWARD SURGE CURRENT. (A) 60 50 40 30 20 10 0 8.3ms Single Half Sine Wave JEDEC Method 0.1 0 20 40 60 80 100 120 140 PERCENT OF RATED PEAK REVERSE VOLTAGE. (%) FIG.5- TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 10 1 2 5 10 20 50 100 NUMBER OF CYCLES AT 60Hz INSTANTANEOUS FORWARD CURRENT. (A) 175 150 125 100 75 50 25 FIG.4- TYPICAL JUNCTION CAPACITANCE 1 JUNCTION CAPACITANCE.(pF) 0.1 HS 2A- HS 2G 0.01 2M 0 0.1 0.001 0.2 0.5 1 2 5 10 20 50 100 200 500 1000 REVERSE VOLTAGE. (V) 0 0.2 0.4 HS2J 0.6 0.8 -HS2 HS HS2 A-HS 2D 2J- HS M HS 2G 1.0 1.2 1.4 FORWARD VOLTAGE. (V) FIG.6- REVERSE RECOVERY TIME CHARACTERISTIC AND TEST CIRCUIT DIAGRAM 50 NONINDUCTIVE 10 NONINDUCTIVE +0.5A DUT (-) PULSE GENERATOR (NOTE 2) NON INDUCTIVE OSCILLOSCOPE (NOTE 1) (+) 0 -0.25A trr (+) 50Vdc (approx) (-) NOTES: 1. Rise Time=7ns max. Input Impedance= 1 megohm 22pf 2. Rise Time=10ns max. Sourse Impedance= 50 ohms -1.0A 1cm SET TIME BASE FOR 5/ 10ns/ cm Version: A06