594D337X-016R2T

594D Vishay Sprague Solid Tantalum Chip Capacitors TANTAMOUNT®, Conformal Coated, Maximum CV, Low ESR FEATURES • New extended range offerings. • Large capacitance rating range. • Lowest ESR for a surface mount tantalum chip capacitor. • 100% surge current conditioning for C, D and R cases. • Terminations: Tin (2) standard. • 8mm, 12mm tape and reel packaging available per EIA481-1 and IEC 286-3. 7” [178mm] standard. 13” [330mm] available. • Case code compatibility with EIA 535BAAE and CECC30801 molded chips. PERFORMANCE / ELECTRICAL CHARACTERISTICS Operating Temperature: -55˚C to +85˚C, (to -125˚C with voltage derating.) Capacitance Range: 1.0µF to 1500µF. Capacitance Tolerance: ±10%, ±20% standard. Voltage Rating: 4 WVDC to 50WVDC. Equivalent Series Resistance: ESR readings measured at 100kHz, +25°C from 3500 milliohm to 30 milliohm. ORDERING INFORMATION 594D TYPE 477 CAPACITANCE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. X0 004 CAPACITANCE DC VOLTAGE RATING TOLERANCE @ + 85°C X0 = ± 20% X9 = ± 10% R CASE CODE See Ratings and Case Codes Table. 2 TERMINATION 2 = 100% Tin 4 = Gold Plated 7 = Hot Solder Dipped 8 = Solder Plated (60/40) Special Order. T PACKAGING T = Tape and Reel 7" [178mm] Reel W = 13” [330mm]Reel - See Tape and Reel specifications This is expressed in volts. To complete the threedigit block, zeros precede the voltage rating. A decimal point is indicated by an "R" (6R3 = 6.3 volts). Note: Preferred Tolerance and reel sizes are in bold. We reserve the right to supply higher voltage ratings and tighter capacitance tolerance capacitors in the same case size. Voltage substitutions will be marked with the higher voltage rating. DIMENSIONS in inches [millimeters] W Tantalum Wire Nib Identifies Anode (+) Terminal L Max. D Ref. A B J Max. J Max. H CASE CODE B C D R L (Max.) 0.158 [4.0] 0.281 [7.1] 0.293 [7.5] 0.283 [7.2] W H 0.110 + 0.012 - 0.016 0.075 + 0.012 - 0.024 [2.8 + 0.3 - 0.4] [1.9 + 0.3 - 0.6] 0.126 ± 0.12 0.098 ± 0.012 [3.2 ± 0.3] [2.5 ± 0.3] 0.170 ± 0.012 0.110 ± 0.012 [4.3 ± 0.3] [2.8 ± 0.3] 0.235 ± 0.012 0.136 ± 0.012 [6.0 ± 0.3] [3.5 ± 0.3] A 0.031 ± 0.012 [0.80 ± 0.30] 0.051 ± 0.012 [1.3 ± 0.30] 0.051 ± 0.012 [1.3 ± 0.30] 0.051 ± 0.012 [1.3 ± 0.30] B 0.097 ± 0.016 [2.5 ± 0.4] 0.180 ± 0.024 [4.6 ± 0.6] 0.180 ± 0.024 [4.6 ± 0.6] 0.180 ± 0.024 [4.6 ± 0.6] D (Ref.) 0.138 [3.5] 0.236 [6.0] 0.253 [6.4] 0.243 [6.2] J (Max.) 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] 0.004 [0.1] Note: The anode termination (D less B) will be a minimum of 0.012" [0.3mm]. www.vishay.com 66 For technical questions, contact tantalum@vishay.com Document Number 40006 Revision 09-Mar-05 594D Vishay Sprague RATINGS AND CASE CODES µF Std. 1.0 1.5 2.2 3.3 4.7 6.8 10 15 22 33 47 68 100 120 150 180 220 270 330 390 470 560 680 1000 1500 4V Ext. Std. 6.3V Ext. 10V Std. Ext. Std. 16V Ext. 20V Std. Ext. Std. 25V Ext. 35V Std. Ext. Std. B 50V Ext. B B B B B B B B C C D D D C* R C D R R R C/D D R R R D R R R C B B B B C R C/D R C C D D B B C C D B C D B D C R D R D D R C C R R B D C D R B C C D B* C C B B *Preliminary values, contact factory for availability. STANDARD / EXTENDED RATINGS CAPACITANCE (µF) 33 100* 150 150 270 330* 470 470 680 1500 22 100 120 220 220 330 330 390 470 470 680 1000 CASE CODE B B* B C D C* C R D R B B C C D C D R D R R R Max. DCL @ + 25°C (µA) 1.3 4.0* 6.0 6.0 10.8 13.2* 18.8 18.8 27.2 60.0 1.4 6.3 7.6 13.9 13.9 20.8 20.8 24.6 29.6 29.6 42.8 63.0 Max. DF @ + 25°C 120 Hz (%) 6 8* 8 8 8 8* 10 10 12 20 6 6 8 8 8 8 8 8 10 10 12 16 Max. ESR @ + 25°C 100kHz (Ohms) 0.38 0.30* 0.25 0.08 0.06 0.08* 0.075 0.045 0.060 0.030 0.380 0.250 0.085 0.080 0.065 0.080 0.060 0.045 0.060 0.050 0.045 0.030 Max. RIPPLE 100kHz Irms (Amps) 0.47 0.53* 0.58 1.17 1.58 1.17* 1.21 2.36 1.58 2.89 0.47 0.58 1.48 1.37 1.52 1.17 1.58 2.36 1.58 2.24 2.36 2.89 PART NUMBER** 594D336X_004B2T 594D107X_004B2T* 594D157X_004B2T 594D157X_004C2T 594D277X_004D2T 594D337X_004C2T* 594D477X_004C2T 594D477X_004R2T 594D687X_004D2T 594D158X_004R2T 594D226X_6R3B2T 594D107X_6R3B2T 594D127X_6R3C2T 594D227X_6R3C2T 594D227X_6R3D2T 594D337X_6R3C2T 594D337X_6R3D2T 594D397X_6R3R2T 594D477X_6R3D2T 594D477X_6R3R2T 594D687X_6R3R2T 594D108X_6R3R2T 4 WVDC @ + 85°C, SURGE = 5.2 V . . . 2.7 WVDC @ + 125°C, SURGE = 3.4 V 6.3 WVDC @ + 85°C, SURGE = 8 V . . . 4 WVDC @ + 125°C, SURGE = 5 V *Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print. Document Number 40006 Revision 09-Mar-05 For technical questions, contact tantalum@vishay.com www.vishay.com 67 594D Vishay Sprague STANDARD / EXTENDED RATINGS CAPACITANCE (µF) 15 33 47 68 68 100 100 150 150 220 220 330 330 470 680 15 33 33 47 47 68 68 100 100 150 180 220 330 4.7 6.8 10 22 22 47 47 100 120 3.3 10 15 22 33 47 68 68 100 2.2 4.7 6.8 15 15 22 33 47 Max. ESR Max. DF @ + 25°C @ + 25°C CASE 120 Hz 100kHz CODE PART NUMBER** (%) (Ohms) 10 WVDC @ + 85°C, SURGE = 13 V . . . 7 WVDC @ + 125°C, SURGE = 8 V 0.50 594D156X_010B2T B 6 1.5 0.50 594D336X_010B2T B 6 3.3 0.40 594D476X_010B2T B 6 4.7 0.350 594D686X_010B2T B 6 6.8 0.100 594D686X_010C2T C 6 6.8 0.250 594D107X_010B2T B 12 10 0.095 594D107X_010C2T C 8 10 0.090 594D157X_010C2T C 8 15 0.075 594D157X_010D2T D 8 15 0.100 594D227X_010C2T C 8 22 0.065 594D227X_010D2T D 8 22 0.065 594D337X_010D2T D 8 33 0.045 594D337X_010R2T R 8 33 0.045 594D477X_010R2T R 10 47 0.045 594D687X_010R2T R 14 68 Max. DCL @ + 25°C (µA) B B C B C C D C D D R R R B B B B C C D D R 16 WVDC @ + 85°C, SURGE = 20 V . . . 10 WVDC @ + 125°C, SURGE = 12 V 2.4 594D156X_016B2T 0.55 6 5.3 594D336X_016B2T 0.500 6 5.3 594D336X_016C2T 0.150 6 7.5 594D476X_016B2T 0.72 6 7.5 594D476X_016C2T 0.110 6 10.9 594D686X_016C2T 0.123 6 10.9 594D686X_016D2T 0.095 6 16 594D107X_016C2T 0.080 8 16 594D107X_016D2T 0.075 8 24 594D157X_016D2T 0.085 8 28.8 594D187X_016R2T 0.055 8 35.2 594D227X_016R2T 0.055 8 52.8 594D337X_016R2T 0.055 8 Max. RIPPLE 100kHz Irms (Amps) 0.41 0.41 0.46 0.49 1.05 0.57 1.08 1.11 1.41 1.05 1.52 1.52 2.36 2.36 2.36 0.39 0.41 0.86 0.34 1.00 0.95 1.26 1.17 1.41 1.33 2.13 2.13 2.13 0.31 0.31 0.32 0.38 0.86 0.89 1.26 1.33 1.77 0.24 0.31 0.70 0.74 1.05 1.07 1.00 1.60 1.67 0.22 0.25 0.51 0.52 0.75 0.75 1.12 1.12 20 WVDC @ + 85°C, SURGE = 26 V . . . 13 WVDC @ + 125°C, SURGE = 16 V 0.90 6 594D475X_020B2T 0.9 0.90 6 594D685X_020B2T 1.4 0.85 6 594D106X_020B2T 2.0 0.60 6 594D226X_020B2T 4.4 0.150 6 594D226X_020C2T 4.4 0.140 6 594D476X_020C2T 9.4 0.095 6 594D476X_020D2T 9.4 0.085 8 594D107X_020D2T 20 0.080 8 24 594D127X_020R2T 25 WVDC @ + 85°C, SURGE = 32 V . . . 17 WVDC @ + 125°C, SURGE = 20 V 0.8 6 1.50 594D335X_025B2T B 2.5 6 0.900 594D106X_025B2T B 3.8 6 0.220 594D156X_025C2T C 5.5 6 0.200 594D226X_025C2T C 8.3 6 0.130 594D336X_025D2T D 11.8 6 0.130 594D476X_025D2T D 17 6 0.150 594D686X_025D2T D 17 6 0.095 594D686X_025R2T R 25 8 0.090 594D107X_025R2T R 35 WVDC @ + 85°C, SURGE = 46 V . . . 23 WVDC @ + 125°C, SURGE = 28 V B 0.8 594D225X_035B2T 6 1.70 B 1.6 594D475X_035B2T 6 1.40 C 2.4 594D685X_035C2T 6 0.43 C 5.3 594D156X_035C2T 6 0.40 D 5.3 594D156X_035D2T 6 0.27 D 7.7 594D226X_035D2T 6 0.27 R 11.6 594D336X_035R2T 6 0.20 R 16.6 594D476X_035R2T 6 0.20 *Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print. www.vishay.com 68 For technical questions, contact tantalum@vishay.com Document Number 40006 Revision 09-Mar-05 594D Vishay Sprague STANDARD / EXTENDED RATINGS CAPACITANCE (µF) CASE CODE Max. DCL @ + 25°C (µA) Max. DF @ + 25°C 120 Hz (%) Max. ESR @ + 25°C 100kHz (Ohms) Max. RIPPLE 100kHz Irms (Amps) PART NUMBER** 50 WVDC @ + 85°C, SURGE = 65 V . . . 33 WVDC @ + 125°C, SURGE = 38 V 1.0 4.7 6.8 15 B C D R 594D105X_050B2T 594D475X_050C2T 594D685X_050D2T 594D156X_050R2T 0.5 2.4 3.4 7.5 4 6 6 6 3.5 1.0 .45 .35 0.16 0.33 0.58 0.85 *Preliminary values, contact factory for availability. For 10% tolerance, specify "9"; for 20% tolerance, change to "0". Extended Range ratings in bold print. TYPICAL CURVES @ + 25°C, IMPEDANCE AND ESR VS FREQUENCY 1000 "B" Case 100 "C" Case IMPEDANCE IMPEDANCE 10 ESR 100 ESR OHMS 10 2.2µF, 35 VDC 1 OHMS 1.0 15µF, 25 VDC 0.1 22µF, 6.3 VDC 120µF, 6.3 VDC 0.1 100 1K 10K 100K 1M 10M FREQUENCY IN HERTZ 0.01 100 1K 10K 100K 1M 10M FREQUENCY IN HERTZ "D" Case 100 IMPEDANCE ESR 10 10 100 "R" Case IMPEDANCE ESR OHMS 1.0 33µF, 25 VDC 220µF, 6.3 VDC 0.1 OHMS 1.0 390µF, 6.3 VDC 0.1 33µF, 35 VDC 0.01 100 1K 10K 100K 1M 10M 0.01 100 1K 10K 100K 1M 10M FREQUENCY IN HERTZ FREQUENCY IN HERTZ Document Number 40006 Revision 09-Mar-05 For technical questions, contact tantalum@vishay.com www.vishay.com 69 594D Vishay Sprague PERFORMANCE CHARACTERISTICS 1. Operating Temperature: Capacitors are designed to operate over the temperature range of - 55°C to + 85°C. Capacitors may be operated to + 125°C with voltage derating to two-thirds the + 85°C rating. + 85°C Rating Working Voltage (V) 4.0 6.3 10 16 20 25 35 50 Surge Voltage (V) 5.2 8 13 20 26 32 46 65 6. Dissipation Factor: The dissipation factor, determined from the expression 2πfRC, shall not exceed values listed in the Standard Ratings Table. Measurements shall be made by the bridge method at, or referred to, a frequency of 120 Hz and a temperature of + 25°C. Leakage Current: Capacitors shall be stabilized at the rated temperature for 30 minutes. Rated voltage shall be applied to capacitors for 5 minutes using a steady source of power (such as a regulated power supply) with 1000 ohm resistor connected in series with the capacitor under test to limit the charging current. Leakage current shall then be measured. 1.1 6.1 + 125°C Rating Working Voltage (V) 2.7 4 7 10 13 17 23 33 Surge Voltage (V) 3.4 5 8 12 16 20 28 38 7. Note that the leakage current varies with applied volt age. See graph below for the appropriate adjustment factor. 2. DC Working Voltage: The DC working voltage is the maximum operating voltage for continuous duty at the rated temperature. Surge Voltage: The surge DC rating is the maximum voltage to which the capacitors may be subjected under any conditions, including transients and peak ripple at the highest line voltage. Surge Voltage Test: Capacitors shall withstand the surge voltage applied in series with a 33 ohm ± 5% resistor at the rate of one-half minute on, one-half minute off, at + 85°C, for 1000 successive test cycles. Following the surge voltage test, the dissipation factor and the leakage current shall meet the initial requirements; the capacitance shall not have changed more than ± 10%. Capacitance Tolerance: The capacitance of all capacitors shall be within the specified tolerance limits of the normal rating. Capacitance measurements shall be made by means of polarized capacitance bridge. The polarizing volt age shall be of such magnitude that there shall be no reversal of polarity due to the AC component. The maximum voltage applied to capacitors during measurement shall be 2 volts rms at 120 Hz at +25°C. If the AC voltage applied is less than one-half volt rms, no DC bias is required. Accuracy of the bridge shall be within ± 2%. Capacitance Change With Temperature: The capacitance change with temperature shall not exceed the following percentage of the capacitance measured at + 25°C: - 55°C - 10% + 85°C + 10% + 125°C + 12% TYPICAL LEAKAGE CURRENT FACTOR RANGE 100 3. + 125°C + 85°C 10 + 55°C 3.1 + 25°C Leakage Current Factor 1.0 0°C 3.2 0.1 - 55°C 4. 4.1 0.01 0.001 0 10 20 30 40 50 60 70 Percent of Rated Voltage 80 90 100 5. 7.1 7.2 7.3 At + 25°C, the leakage current shall not exceed the value listed in the Standard Ratings Table. At + 85°C, the leakage current shall not exceed 10 times the value listed in the Standard Ratings Table. At + 125°C, the leakage current shall not exceed 12 times the value listed in the Standard Ratings Table. www.vishay.com 70 For technical questions, contact tantalum@vishay.com Document Number 40006 Revision 09-Mar-05 594D Vishay Sprague PERFORMANCE CHARACTERISTICS (Continued) 8 ESR (Equivalent Series Resistance) Measurement shall be made by the bridge method at a frequency of 100kHz and a temperature of + 25°C. The equivalent Series Resistance shall not exceed the value listed in the Standard Ratings Table. Life Test: Capacitors shall withstand rated DC voltage applied at + 85°C or two-thirds rated voltage applied at + 125°C for 2000 hours. Following the life test, the dissipation factor shall meet the initial requirement; the capacitance change shall not exceed ± 10%; the leakage current shall not exceed 125% of the initial requirement. Humidity Test: Capacitors will withstand 1000 hours at + 40˚C, 90% to 95% relative humidity, with no voltage applied. Following the humidity test, capacitance change shall not exceed ± 10% of the initial value, dissipation factor shall not exceed 150% of the initial requirement; leakage current shall not exceed 200% of the initial requirement at + 25˚C. Solderability: Capacitors will meet the solderability requirements of ANSI/J-STD-002, Test B, Category 3. Resistance to Soldering Heat: Capacitors mounted on a substrate will withstand + 260°C for 5 seconds. 12.1 Following the resistance to soldering heat test, capacitance, dissipation factor and DC leakage current shall meet the initial requirement. Marking: The small body area of these capacitors does not allow elaborate marking schemes. All required information is present on the carton or package in which the parts are shipped; in addition, part number, quantity and date code are indicated on the reels. Terminal Strength: Per IEC-384-3, minimum of 5N shear force. Environmental: Mercury, CFC and ODS materials are not used in the manufacture of these capacitors. Flammability: Encapsulant materials meet UL94 V0. Capacitor Failure Mode: The predominant failure mode for solid tantalum capacitors is increased leakage current resulting in a shorted circuit. Capacitor failure may result from excess forward or reverse DC voltage, surge current, ripple current, thermal shock or excessive temperature. The increase in leakage is caused by a breakdown of the Ta2O5 dielectric. For additional information on leakage failure of solid tantalum chip capacitors, refer to Vishay Sprague Technical Paper, “Leakage Failure Mode in Solid Tantalum Chip Capacitors.” 13. 8.1 9. 14. 15. 16. 17. 9.1 10. 10.1 11. 12. GUIDE TO APPLICATION 1.0 Recommended rated working voltage guidelines: (-55°C to + 85°C) Standard Conditions, for example; output filters Capacitor Voltage Rating (V) Operating Voltage (V) 4 6.3 10 16 20 25 35 50 2.5 3.6 6 10 12 15 24 28 2.0 A-C Ripple Current: The maximum allowable ripple current shall be determined from the formula: Irms = P RESR where, P = Power Dissipation in Watts @ + 25°C as given in the table in Paragraph Number 6.0 (Power Dissipation) RESR = The capacitor Equivalent Series Resistance at the specified frequency. 3.0 A-C Ripple Voltage: The maximum allowable ripple voltage shall be determined from the formula: Vrms = Z or, from the formula: where, Vrms = Irms x Z P RESR Severe Conditions, for example; input filters Capacitor Voltage Rating (V) Operating Voltage (V) 4 6.3 10 16 20 25 35 50 2.5 3.3 5 8 10 12 15 24 P = Power Dissipation in Watts @ + 25°C as given in the table in Paragraph Number 6.0 (Power Dissipation). RESR = The capacitor Equivalent Series Resistance at the specified frequency. Z 3.1 = The capacitor Impedance at the specified frequency. The sum of the peak AC voltage plus the DC voltage shall not exceed the DC voltage rating of the capacitor. www.vishay.com 71 Document Number 40006 Revision 09-Mar-05 For technical questions, contact tantalum@vishay.com 594D Vishay Sprague GUIDE TO APPLICATION (Continued) 3.2 The sum of the negative peak AC voltage plus the applied DC voltage shall not allow a voltage reversal exceeding 10% of the DC working voltage at + 25°C. Reverse Voltage: These capacitors are capable of withstanding peak voltages in the reverse direction equal to 10% of the DC rating at + 25°C and 5% of the DC rating at + 85°C. Temperature Derating: If these capacitors are to be operated at temperatures above + 25°C, the permissible rms ripple current or voltage shall be calculated using the derating factors as shown: Temperature + 25°C + 85°C + 125°C Derating Factor 1.0 0.9 0.4 TEMPERATURE (°C) 4.0 plate methods. The Soldering Profile charts show typical recomended time/temperature conditions for soldering. Preheating is recommended. The recommended maximum ramp rate is 2°C per second. Attachment with a soldering iron is not recommended due to the difficulty of controlling temperature and time at temperature. The soldering iron must never come in contact with the capacitor. 5.0 RECOMMENDED REFLOW SOLDERING PROFILE Recommended Pb Free Reflow Soldering Profile 245°C 217°C 200°C 60 sec 150°C 60 - 150 sec Preheat 10 sec 6.0 Power Dissipation: Power dissipation will be affected by the heat sinking capability of the mounting surface. Non-sinusoidal ripple current may produce heating effects which differ from those shown. It is important that the equivalent Irms value be established when calculating permissible operating levels. (Power dissipation calculated using + 25°C temperature rise.) Maximum Permissible Power Dissipation @ + 25°C (Watts) in free air 0.085 0.110 0.150 0.250 25°C TIME (seconds) Large Case Codes: D, R Recommended Pb Free Reflow Soldering Profile 260°C 217°C 200°C 60 sec 150°C 60 - 150 sec Preheat 10 sec Case Code B C D R 7.0 Printed Circuit Board Material: The capacitors are compatible with most commonly used printed circuit board materials (alumina substrates, FR4, FR5, G10, PTFE-fluorocarbon and porcelanized steel). If your desired board material is not shown there, please contact the Tantalum Marketing Department for assistance in determining compatibility. 8. Attachment: TEMPERATURE (°C) TEMPERATURE (°C) 25°C TIME (seconds) Large Case Codes: B, C Recommended SnPb Reflow Soldering Profile 225°C 183°C 150°C 60 sec 100°C 60 - 90 sec Preheat 10 sec 8.1 Solder Paste: The recommended thickness of the solder paste after applications is .007" ± .001" [1.78mm ± .025mm]. Care should be exercised in selecting the solder paste. The metal purity should be as high as practical. The flux (in the paste) must be active enough to remove the oxides formed on the metallization prior to the exposure to soldering heat. 8.2 Soldering: Capacitors can be attached by conventional soldering techniques, vapor phase, convection, infrared reflow wave soldering and hot 25°C TIME (seconds) All Case Codes www.vishay.com 72 For technical questions, contact tantalum@vishay.com Document Number 40006 Revision 09-Mar-05 594D Vishay Sprague 9.0 Recommended Mounting Pad Geometries: The nib must have sufficient clearance to avoid electrical contact with other components. The width dimension indicated is the same as the maximum width of the capacitor. This is to minimize lateral movement. 10.0 Cleaning (Flux Removal) After Soldering: The 594D is compatible with all commonly used solvents such as TES, TMS, Prelete, Chlorethane, Terpene and aqueous cleaning media. However, CFC/ODS products are not used in the production of these devices and are not recommended. Solvents containing methylene chloride or other epoxy solvents should be avoided since these will attack the epoxy encapsulation material. REFLOW SOLDER PADS* in inches [millimeters] B C B A * Pads for B, C and D case codes are otherwise pad compatible with Type 293D, B, C and D case codes respectively. CASE CODE B C D R WIDTH (A) 0.120 [3.0] 0.136 [3.5] 0.180 [4.6] 0.245 [6.3] PAD METALLIZATION SEPARATION (C) (B) 0.065 0.065 [1.7] [1.7 0.120 0.090 [3.1] [2.3] 0.145 0.090 [3.7] [2.3] 0.145 0.090 [3.7] [2.3] TAPE AND REEL PACKAGING in inches [millimeters] Top Cover Tape Thickness R Min. Standard orientation is with the cathode (-) nearest to the sprocket holes per EIA-481-1 and IEC 286-3. Carrier Bending Radius (Note 2) Embossment Units Per Reel Case Code B C D R Tape Width 12mm 12mm 12mm 12mm Component Pitch 4mm 8mm 8mm 8mm 7" [178] Reel 2000 500 500 600 13" [330] Reel 8000 3000 2500 — Document Number 40006 Revision 09-Mar-05 For technical questions, contact tantalum@vishay.com www.vishay.com 73 594D Vishay Sprague TAPE AND REEL PACKAGING in inches [millimeters] Note: Metric dimensions will govern. Dimensions in inches are rounded and for reference only. T2 Max. .024 [0.600] Max. .157 ± .004 [4.0 ± 0.10] Deformation .059 + .004 - 0.0 Between Embossments [1.5 + 0.10 - 0.0] Top Cover Tape B1 Max. (Note 6) K0 Top Cover Tape .004 [0.10] Max. 10 Pitches Cumulative Tolerance on Tape .069 ± .004 [1.75 ± 0.10] .079 ± .002 Embossment [2.0 ± 0.05] 20° A0 .030 [0.75] Min. (Note 3) B0 .030 [0.75] Min. (Note 4) Center Lines of Cavity P1 D1 Min. For Components .079 x .047 [2.0 x 1.2] and Larger. (Note 5) Maximum Cavity Size (Note 1) F W Maximum Component Rotation (Side or Front Sectional View) ± 0.008 [0.2] For Tape Feeder Reference only including draft. Concentric around B0 (Note 5) USER DIRECTION OF FEED Cathode (-) Anode (+) DIRECTION OF FEED 20° Maximum Component Rotation Typical Component Cavity Center Line Typical Component Center Line 3.937 [100.0] .039 [1.0] Max. Tape .039 [1.0] Max. 9.843 [250.0] Camber (Top View) Allowable Camber to be .039/3.937 [1/100] Non-Cumulative Over 9.843 [250.0] B0 Tape and Reel Specifications: All case codes are available on plastic embossed tape per EIA-481-1. Tape reeling per IEC 286-3 is also available. Standard reel diameter is 7" [178mm]. 13" [330mm] reels are available and recommended as the most cost effective packaging method. The most efficient packaging quantities are full reel increments on a given reel diameter. The quantities shown allow for the sealed empty pockets required to be in conformance with EIA-481-1. Reel size and packaging orientation must be specified in the Vishay Sprague part number. R (Min.) (Note 2) 1.181 [30.0] 1.181 [30.0] T2 (Max.) 0.256 [6.5] 0.256 [6.5] A0 (Top View) TAPE SIZE 12mm 12mm Double Pitch B1 (Max.) (Note 6) 0.323 [8.2] 0.323 [8.2] D1 (Min.) (Note 5) 0.059 [1.5] 0.059 [1.5] F 0.217 ± 0.002 [5.5 ± 0.05] 0.453 ± 0.004 [11.5 ± 0.03] P1 0.157 ± 0.004 [4.0 ± 0.1] 0.315 ± 0.004 [8.0 ± 0.1] W 0.472 ± 0.012 [12.0 ± 0.30] 0.945 ± 0.012 [24.0 ± 0.03] A0 B0 K0 (Note 1) Notes: 1. A0B0K0 are determined by the maximum dimensions to the ends of the terminals extending from the component body and/or the body dimensions of the component. The clearance between the ends of the terminals or body of the component to the sides and depth of the cavity (A0B0K0) must be within 0.002" [0.05mm] minimum and 0.020" [0.50mm] maximum. The clearance allowed must also prevent rotation of the component within the cavity of not more than 20 degrees. 2. Tape with components shall pass around radius "R" without damage. The minimum trailer length may require additional length to provide R minimum for 12mm embossed tape for reels with hub diameters approaching N minimum. 3. This dimension is the flat area from the edge of the sprocket hole to either the outward deformation of the carrier tape between the embossed cavities or to the edge of the cavity whichever is less. 4. This dimension is the flat area from the edge of the carrier tape opposite the sprocket holes to either the outward deformation of the carrier tape between the embossed cavity or to the edge of the cavity whichever is less. 5. The embossment hole location shall be measured from the sprocket hole controlling the location of the embossment. Dimensions of embossment location and hole location shall be applied independent of each other. 6. B1 dimension is a reference dimension for tape feeder clearance only. www.vishay.com 74 For technical questions, contact tantalum@vishay.com Document Number 40006 Revision 09-Mar-05