V-735P

V-735 P Vishay Sprague Film Capacitors, High Current, Wrap-and-Fill, Metallized Polypropylene FEATURES • • • • • Wire or lug terminals High stability High ripple to 30 A Low inductance Low ESR • Compliant to RoHS directive 2002/95/EC PERFORMANCE CHARACTERISTICS Operating Temperature: - 55 °C to + 105 °C Capacitance Range: 1.0 µF to 30.0 µF Capacitance Tolerance: ± 10 %, ± 5 % DC Voltage Rating: 100 WVDC to 400 WVDC Equivalent Series Resistance: 20 kHz to 100 kHz Dissipation Factor: 0.1 % maximum Measured at 1000 Hz, at + 25 °C Humidity Test: 95 % relative humidity at + 40 °C for 250 h. No visible damage. Maximum Δ CAP ± 1.0 % Minimum IR = 20 % of initial limit Maximum DF = 0.12 % PHYSICAL CHARACTERISTICS Pull Test: Wire Leads: - 5 lb (2.3 kg) for one min. No physical damage. Terminal Lugs: - 10 lb (4.5. kg) for one min. No physical damage. Lead Bend: After three complete consecutive bends. No damage. Marking: Sprague® trademark, type or part number, capacitance and voltage. ΔV/ΔT: 10 V/ms maximum Voltage Test: 200 % of rated voltage for 2 min Insulation Resistance: Measured at 100 WVDC after a 2 min charge. At + 25 °C: 200 000 MΩ/µF, or 400 000 MΩ minimum Vibration Test (Condition B): No mechanical damage, short, open or intermittent circuits. DC Life Test: 140 % of rated voltage for 1000 h at + 105 °C. No visible damage. No open or short circuits. Maximum Δ CAP ± 1.0 % Minimum IR = 50 % of initial limit Maximum DF = 0.10 % DIMENSIONS in inches [millimeters] Terminal Style L 1.750 [44.45] Min. L ± 0.062 [1.57] 1.750 [44.45] Min. D Max. Tinned Solid Copper Wire (1) D Max.< 0.700 [17.78], No. 20 AWG Wire 0.032 [0.812] Nominal Diameter D Max. ≥ 0.700 [17.78], No. 18 AWG Wire 0.040 [1.016] Nominal Diameter Terminal Style H Tinned Solid Copper Lug L1 ± 0.062 [1.57] L2 ± 0.062 [1.57] 0.360 ± 0.005 [9.14 ± 0.13] L ± 0.062 [1.57] 0.156 ± 0.005 Dia. [3.96 ± 0.13] 0.312 [7.9] Min. 0.0032 ± 0.002 [0.81 ± 0.05] L1 = L + 0.766 [19.46] L2 = L + 0.437 [11.10] D Max. Note (1) Leads to be within ± 0.062" [1.57 mm] of center line at egress but not less than 0.031" [0.79 mm] from edge (Terminal Style L only). Document Number: 42093 Revision: 12-Mar-09 For technical questions, contact: spresale@vishay.com www.vishay.com 25 V-735 P Vishay Sprague Film Capacitors, High Current, Wrap-and-Fill, Metallized Polypropylene STANDARD RATINGS in inches [millimeters] CAPACITANCE PART NUMBER (1) (µF) MAXIMUM RIPPLE CURRENT ESR LIMIT (ARMS) at 20 kHz - 100 kHz (mΩ) CASE TEMPERATURE at 20 kHz to 100 kHz + 25 °C + 35 °C + 45 °C + 55 °C + 65 °C + 75 °C + 85 °C D L Terminal Style L - Units with Wire Leads 100 WVDC 0.531 [13.49] 0.750 [19.05] 15.0 9.2 8.5 7.8 7.0 6.0 4.9 4.5 0.596 [15.14] 0.938 [23.81] 12.0 10.8 10.0 9.1 8.2 7.0 5.8 5.3 0.717 [18.21] 0.938 [23.81] 11.0 12.1 11.2 10.3 9.2 8.0 6.5 5.9 0.733 [18.62] 1.250 [31.75] 10.0 13.8 12.7 11.6 10.4 9.0 7.4 6.7 0.898 [22.81] 1.500 [38.10] 9.0 15.0 15.0 14.2 12.7 11.0 9.0 8.2 1.000 [25.40] 2.250 [57.15] 8.0 15.0 15.0 15.0 15.0 13.6 11.1 10.0 1.200 [30.48] 2.250 [57.15] 6.0 15.0 15.0 15.0 15.0 15.0 12.4 11.4 200 WVDC 0.512 [13.01] 1.250 [31.75] 20.0 7.3 7.3 7.3 7.3 7.2 5.9 5.4 0.698 [17.73] 1.250 [31.75] 15.0 12.0 12.0 11.3 10.1 8.7 7.1 6.5 0.747 [18.97] 1.500 [38.10] 13.0 15.0 13.8 12.6 11.3 9.8 8.0 7.3 0.862 [21.89] 1.750 [44.45] 11.0 15.0 15.0 14.7 13.1 11.4 9.3 8.5 1.030 [26.16] 2.250 [57.15] 9.0 15.0 15.0 15.0 15.0 13.8 11.3 10.3 1.440 [36.58] 2.250 [57.15] 6.0 15.0 15.0 15.0 15.0 15.0 14.1 12.8 400 WVDC 0.713 [18.11] 1.500 [38.10] 19.0 9.5 9.5 9.5 9.5 9.5 7.8 7.1 0.895 [22.73] 1.750 [44.45] 15.0 15.0 15.0 15.0 13.4 11.6 9.5 8.7 1.086 [27.58] 1.750 [44.45] 12.0 15.0 15.0 15.0 15.0 13.1 10.7 9.8 1.192 [30.28] 2.250 [57.15] 10.0 15.0 15.0 15.0 15.0 15.0 12.5 11.4 1.668 [42.37] 2.250 [57.15] 6.0 15.0 15.0 15.0 15.0 15.0 15.0 14.1 Terminal Style H - Units with Terminal Lugs 100 WVDC 0.531 [13.49] 0.875 [22.23] 15.0 10.3 9.5 8.7 7.8 6.7 5.5 5.0 0.596 [15.14] 1.062 [26.97] 12.0 12.0 11.0 10.0 8.9 7.8 6.3 5.8 0.717 [18.21] 1.062 [26.97] 11.0 13.3 12.3 11.2 10.0 8.7 7.1 6.5 0.733 [18.62] 1.375 [34.93] 10.0 14.8 13.7 12.5 11.2 9.7 7.9 7.2 0.898 [22.81] 1.625 [41.28] 9.0 17.8 16.5 15.0 13.5 11.7 9.5 8.7 1.000 [25.40] 2.375 [60.33] 8.0 21.6 20.0 18.3 16.4 14.2 11.6 10.6 1.200 [30.48] 2.375 [60.33] 6.0 24.3 22.5 20.5 18.4 15.9 13.0 11.9 200 WVDC 0.512 [13.00] 1.375 [34.93] 20.0 7.3 7.3 7.3 7.3 7.3 6.4 5.8 0.698 [17.73] 1.375 [34.93] 15.0 14.3 13.3 12.1 10.8 9.4 7.7 7.0 0.747 [18.97] 1.625 [41.28] 13.0 15.9 14.7 13.5 12.0 10.4 8.5 7.8 0.862 [21.89] 1.875 [47.63] 11.0 18.3 17.0 15.5 13.9 12.0 9.8 8.9 1.030 [26.16] 2.375 [60.33] 9.0 22.4 20.7 18.9 16.9 14.6 12.0 10.9 1.440 [36.58] 2.375 [60.33] 6.0 27.4 25.4 23.2 20.7 17.9 14.7 13.4 400 WVDC 0.713 [18.11] 1.625 [41.28] 19.0 9.5 9.5 9.5 9.5 9.5 8.3 7.5 0.895 [22.73] 1.875 [47.63] 15.0 15.0 15.0 15.0 14.2 12.3 10.0 9.1 1.086 [27.58] 1.875 [47.63] 12.0 21.1 19.5 17.8 15.9 13.8 11.3 10.3 1.192 [30.28] 2.375 [60.33] 10.0 24.4 22.6 20.6 18.5 16.0 13.1 11.9 1.668 [42.37] 2.375 [60.33] 6.0 30.0 27.8 25.4 22.7 19.7 16.1 14.7 CASE SIZE 1.0 2.0 3.0 5.0 10.0 20.0 30.0 1.0 2.0 3.0 5.0 10.0 20.0 1.0 2.0 3.0 5.0 10.0 V-735P105X9100L V-735P205X9100L V-735P305X9100L V-735P505X9100L V-735P106X9100L V-735P206X9100L V-735P306X9100L V-735P105X9200L V-735P205X9200L V-735P305X9200L V-735P505X9200L V-735P106X9200L V-735P206X9200L V-735P105X9400L V-735P205X9400L V-735P305X9400L V-735P505X9400L V-735P106X9400L 1.0 2.0 3.0 5.0 10.0 20.0 30.0 1.0 2.0 3.0 5.0 10.0 20.0 1.0 2.0 3.0 5.0 10.0 V-735P105X9100H V-735P205X9100H V-735P305X9100H V-735P505X9100H V-735P106X9100H V-735P206X9100H V-735P306X9100H V-735P105X9200H V-735P205X9200H V-735P305X9200H V-735P505X9200H V-735P106X9200H V-735P206X9200H V-735P105X9400H V-735P205X9400H V-735P305X9400H V-735P505X9400H V-735P106X9400H Notes (1) Part Numbers listed are for a capacitance tolerance of ± 10 %. To specifiy ± 5 % tolerance, change the “X9” in the Part Number to “X5”. • Other capacitance values and voltage ratings are available upon request ORDERING INFORMATION V-735P TYPE 105 CAPACITANCE X9 CAPACITANCE TOLERANCE X9 = ± 10 % X5 = ± 5 % 100 DC VOLTAGE RATING L TERMINAL STYLE This is expressed in picofarads. The first two digits are the significant figures. The third is the number of zeros to follow. This is expressed in volts. L = Wire Leads H = Lugs www.vishay.com 26 For technical questions, contact: spresale@vishay.com Document Number: 42093 Revision: 12-Mar-09 Legal Disclaimer Notice Vishay Disclaimer ALL PRODUCT, PRODUCT SPECIFICATIONS AND DATA ARE SUBJECT TO CHANGE WITHOUT NOTICE TO IMPROVE RELIABILITY, FUNCTION OR DESIGN OR OTHERWISE. Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf (collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained in any datasheet or in any other disclosure relating to any product. Vishay makes no warranty, representation or guarantee regarding the suitability of the products for any particular purpose or the continuing production of any product. To the maximum extent permitted by applicable law, Vishay disclaims (i) any and all liability arising out of the application or use of any product, (ii) any and all liability, including without limitation special, consequential or incidental damages, and (iii) any and all implied warranties, including warranties of fitness for particular purpose, non-infringement and merchantability. Statements regarding the suitability of products for certain types of applications are based on Vishay’s knowledge of typical requirements that are often placed on Vishay products in generic applications. Such statements are not binding statements about the suitability of products for a particular application. It is the customer’s responsibility to validate that a particular product with the properties described in the product specification is suitable for use in a particular application. Parameters provided in datasheets and/or specifications may vary in different applications and performance may vary over time. All operating parameters, including typical parameters, must be validated for each customer application by the customer’s technical experts. Product specifications do not expand or otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed therein. Except as expressly indicated in writing, Vishay products are not designed for use in medical, life-saving, or life-sustaining applications or for any other application in which the failure of the Vishay product could result in personal injury or death. Customers using or selling Vishay products not expressly indicated for use in such applications do so at their own risk and agree to fully indemnify and hold Vishay and its distributors harmless from and against any and all claims, liabilities, expenses and damages arising or resulting in connection with such use or sale, including attorneys fees, even if such claim alleges that Vishay or its distributor was negligent regarding the design or manufacture of the part. Please contact authorized Vishay personnel to obtain written terms and conditions regarding products designed for such applications. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this document or by any conduct of Vishay. Product names and markings noted herein may be trademarks of their respective owners. Document Number: 91000 Revision: 11-Mar-11 www.vishay.com 1