0
登录后你可以
  • 下载海量资料
  • 学习在线课程
  • 观看技术视频
  • 写文章/发帖/加入社区
会员中心
创作中心
发布
  • 发文章

  • 发资料

  • 发帖

  • 提问

  • 发视频

创作活动
WM8941GEFLV

WM8941GEFLV

  • 厂商:

    WOLFSON

  • 封装:

  • 描述:

    WM8941GEFLV - Mono CODEC with Speaker Driver and Video Buffer - Wolfson Microelectronics plc

  • 数据手册
  • 价格&库存
WM8941GEFLV 数据手册
w DESCRIPTION The WM8941 is a low power, high quality mono CODEC designed for portable applications such as digital still cameras or camcorders. The device integrates support for a differential or single ended mic, and includes drivers for speakers or headphone, and mono line output. External component requirements are reduced as no separate microphone or headphone amplifiers are required. A high performance, low power current-mode video buffer provides inherent short circuit protection. An integrated video buffer is provided which has programmable gain from 0-6dB (6-12dB unloaded), sync-tip clamp and a 3rd order input low pass filter for signal reconstruction. Advanced Sigma Delta Converters are used along with digital decimation and interpolation filters to give high quality audio at sample rates from 8 to 48ks/s. A selectable high pass filter and four fully-programmable notch filters are available in the ADC path. An advanced mixed signal ALC function with noise gate is provided, while readback of PGA gain during ALC operation is supported. The digital audio interface supports Alaw and µ-law companding. An on-chip PLL is provided to generate the required Master Clock from an external reference clock. The PLL clock can also be output if required elsewhere in the system. The WM8941 operates at supply voltages from 2.5 to 3.6V, although the digital supplies can operate at voltages down to 1.71V to save power. Different sections of the chip can also be powered down under software control using the selectable two or three wire control interface. WM8941 is supplied in a very small 4x4mm QFN package, offering high levels of functionality in minimum board area, with high thermal performance. WM8941 Mono CODEC with Speaker Driver and Video Buffer FEATURES • • • • • • • • • Mono CODEC: Audio sample rates:8, 11.025, 16, 22.05, 24, 32, 44.1, 48kHz DAC SNR 98dB, THD -84dB (‘A’-weighted @ 8 – 48ks/s) ADC SNR 94dB, THD -80dB (‘A’-weighted @ 8 – 48ks/s) On-chip Headphone/Speaker Driver - 40mW output power into 16Ω - BTL speaker drive 0.4W into 8Ω Additional MONO Line output Multiple analog or ‘Aux’ inputs, plus analog bypass path Mic Preamps : Differential or single end Microphone Interface - Programmable preamp gain - Pseudo differential inputs with common mode rejection - Programmable ALC / Noise Gate in ADC path Low-noise bias supplied for electret microphones • OTHER FEATURES • Integrated video buffer with LPF and clamp. • Digital Playback Limiter • Programmable high pass filter (wind noise reduction) • 4 notch filters (narrowband noise suppression) • On-chip PLL • Low power, low voltage - 2.5V to 3.6V (digital: 1.71V to 3.6V) • 4x4x0.75mm 28 lead QFN package APPLICATIONS • • Digital still cameras and camcorders General purpose mono audio CODEC with video buffer WOLFSON MICROELECTRONICS plc To receive regular email updates, sign up at http://www.wolfsonmicro.com/enews/ Pre Production, Rev 3.3, December 2007 Copyright ©2007 Wolfson Microelectronics plc WM8941 BLOCK DIAGRAM Pre Production w PP, Rev 3.3, December 2007 2 Pre Production WM8941 TABLE OF CONTENTS DESCRIPTION ................................................................................................................1 FEATURES......................................................................................................................1 APPLICATIONS ..............................................................................................................1 BLOCK DIAGRAM ..........................................................................................................2 PIN CONFIGURATION....................................................................................................5 ORDERING INFORMATION ...........................................................................................5 PIN DESCRIPTION .........................................................................................................6 ABSOLUTE MAXIMUM RATINGS..................................................................................7 RECOMMENDED OPERATING CONDITIONS ..............................................................7 ELECTRICAL CHARACTERISTICS ...............................................................................8 TERMINOLOGY ....................................................................................................................10 AUDIO PATHS OVERVIEW ..........................................................................................12 SIGNAL TIMING REQUIREMENTS ..............................................................................14 SYSTEM CLOCK TIMING .....................................................................................................14 AUDIO INTERFACE TIMING – MASTER MODE ..................................................................14 AUDIO INTERFACE TIMING – SLAVE MODE......................................................................15 CONTROL INTERFACE TIMING – 3-WIRE MODE ..............................................................16 CONTROL INTERFACE TIMING – 2-WIRE MODE ..............................................................17 DEVICE DESCRIPTION................................................................................................18 INTRODUCTION ...................................................................................................................18 INPUT SIGNAL PATH ...........................................................................................................19 ANALOGUE TO DIGITAL CONVERTER (ADC)....................................................................25 INPUT LIMITER / AUTOMATIC LEVEL CONTROL (ALC) ....................................................30 OUTPUT SIGNAL PATH .......................................................................................................43 VOLUME BOOST ..................................................................................................................45 ANALOGUE OUTPUTS.........................................................................................................47 OUTPUT SWITCH ................................................................................................................50 VIDEO BUFFER ....................................................................................................................53 DIGITAL AUDIO INTERFACES.............................................................................................58 AUDIO SAMPLE RATES .......................................................................................................62 MASTER CLOCK AND PHASE LOCKED LOOP (PLL) .........................................................63 COMPANDING......................................................................................................................66 GENERAL PURPOSE INPUT/OUTPUT................................................................................68 CONTROL INTERFACE........................................................................................................68 3-WIRE SERIAL CONTROL MODE ......................................................................................70 READBACK IN 3-WIRE MODE .............................................................................................70 2-WIRE SERIAL CONTROL MODE ......................................................................................71 RESETTING THE CHIP ........................................................................................................71 POWER SUPPLIES ..............................................................................................................71 POWER MANAGEMENT ......................................................................................................74 POP MINIMISATION .............................................................................................................75 REGISTER MAP............................................................................................................76 REGISTER BITS BY ADDRESS ...........................................................................................77 DIGITAL FILTER CHARACTERISTICS ........................................................................89 TERMINOLOGY ....................................................................................................................89 DAC FILTER RESPONSES...................................................................................................90 ADC FILTER RESPONSES...................................................................................................90 HIGHPASS FILTER...............................................................................................................91 NOTCH FILTERS AND LOW PASS FILTER.........................................................................92 w PP, Rev 3.3, December 2007 3 WM8941 Pre Production APPLICATIONS INFORMATION ..................................................................................94 RECOMMENDED EXTERNAL COMPONENTS ....................................................................94 PACKAGE DIAGRAM ...................................................................................................95 IMPORTANT NOTICE ...................................................................................................96 ADDRESS .............................................................................................................................96 w PP, Rev 3.3, December 2007 4 Pre Production WM8941 PIN CONFIGURATION MICBIAS AVDD AGND DCVDD DBVDD DGND ADCDAT SPKROUTP MONOOUT VBIN VBREF VBOUT VBVDD SDIN ORDERING INFORMATION ORDER CODE W M8941GEFL/V W M8941GEFL/RV Note: Reel Quantity = 3,500 TEMPERATURE RANGE -25°C to +85°C -25°C to +85°C PACKAGE 28-lead QFN (4x4x0.75mm) (Pb-free) 28-lead QFN (4x4x0.75mm) (Pb-free, tape and reel) MOISTURE SENSITIVITY LEVEL MSL3 MSL3 PACKAGE BODY TEMPERATURE 260oC 260oC w PP, Rev 3.3, December 2007 5 WM8941 PIN DESCRIPTION PIN 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 NAME MICBIAS AVDD AGND DCVDD DBVDD DGND ADCDAT DACDAT FRAME BCLK MCLK CSB/GPIO MODE/GPIO SCLK SDIN VBVDD VBOUT VBREF VBIN MONOOUT SPKOUTP SPKGND SPKOUTN SPKVDD AUX VMID MICN MICP Supply Supply Supply Supply Supply Digital Output Digital Input Digital Input / Output Digital Input / Output Digital Input Digital Input / Output Digital Input Digital Input Digital Input / Output Supply Analogue Output Analogue Output Analogue Input Analogue Output Analogue Output Supply Analogue Output Supply Analogue Input Reference Analogue Input Analogue Input TYPE Analogue Output Microphone bias Analogue supply Analogue ground Digital Supply (Core) Digital supply (Input/Output) Digital ground ADC digital audio data output DAC digital audio data input DAC and ADC sample rate clock or frame synch Digital audio port clock Master clock input 3-Wire control interface chip select or GPIO pin Control interface mode selection or GPIO pin DESCRIPTION Pre Production 3-Wire control interface clock Input / 2-Wire control interface clock input 3-Wire control interface data Input / 2-Wire control interface data input Vide buffer supply Video buffer TV output Video buffer reference pin Video buffer input Mono output Speaker output positive Speaker ground Speaker output negative Speaker supply Auxiliary analogue input Decoupling for midrail reference voltage Microphone negative input (common mode) Microphone positive input Note: 1. 2. It is recommended that the QFN ground paddle should be connected to analogue ground on the application PCB. Refer to the application note WAN_0118 on “Guidelines on How to Use QFN Packages and Create Associated PCB Footprints” w PP, Rev 3.3, December 2007 6 Pre Production WM8941 ABSOLUTE MAXIMUM RATINGS Absolute Maximum Ratings are stress ratings only. Permanent damage to the device may be caused by continuously operating at or beyond these limits. Device functional operating limits and guaranteed performance specifications are given under Electrical Characteristics at the test conditions specified. ESD Sensitive Device. This device is manufactured on a CMOS process. It is therefore generically susceptible to damage from excessive static voltages. Proper ESD precautions must be taken during handling and storage of this device. Wolfson tests its package types according to IPC/JEDEC J-STD-020B for Moisture Sensitivity to determine acceptable storage conditions prior to surface mount assembly. These levels are: MSL1 = unlimited floor life at 0.546fs 0.546fs -55 29/fs dB +/- 0.035dB -6dB 0 0.5fs +/-0.035 dB 0.454fs 3.7 10.4 21.6 Hz f > 0.546fs 0.546fs -60 21/fs dB +/- 0.025dB -6dB 0 0.5fs +/- 0.025 dB 0.454fs TEST CONDITIONS MIN TYP MAX Pre Production UNIT TERMINOLOGY 1. 2. 3. Stop Band Attenuation (dB) – the degree to which the frequency spectrum is attenuated (outside audio band) Pass-band Ripple – any variation of the frequency response in the pass-band region Note that this delay applies only to the filters and does not include additional delays through other digital circuits. See Table 63 for the total delay. PARAMETER Total Delay (ADC analogue input to digital audio interface output) Total Delay (Audio interface input to DAC analogue output) Table 63 Total Group Delay Notes 1. Wind noise filter is disabled. MIN 28/fs TYP 30/fs MAX 32/fs UNIT fs 33/fs 35/fs 37/fs fs w PP, Rev 3.3, December 2007 88 Pre Production WM8941 DAC FILTER RESPONSES 0.2 0 -20 Response (dB) -40 -60 -80 -100 - 120 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3 0.15 0.1 Response (dB) 0.05 0 -0.05 -0.1 -0.15 -0.2 0 0.1 0.2 Frequency (Fs) 0.3 0.4 0.5 Figure 46 DAC Digital Filter Frequency Response Figure 47 DAC Digital Filter Ripple ADC FILTER RESPONSES 0.2 0 -20 Response (dB) Response (dB) 0.15 0.1 0.05 0 -0.05 -0.1 -0.15 -0.2 -40 -60 -80 -100 - 120 0 0.5 1 1.5 Frequency (Fs) 2 2.5 3 0 0.1 0.2 Frequency (Fs) 0.3 0.4 0.5 Figure 48 ADC Digital Filter Frequency Response Figure 49 ADC Digital Filter Ripple w PP, Rev 3.3, December 2007 89 WM8941 HIGHPASS FILTER Pre Production The WM8941 has a selectable digital high pass filter in the ADC filter path. This filter has two modes, audio and applications. In audio mode the filter is a 1st order IIR with a cut-off of around 3.7Hz. In applications mode the filter is a 2nd order high pass filter with a selectable cut-off frequency. 5 0 -5 -10 Response (dB) 10 0 -10 Response (dB) 0 5 10 15 20 25 30 35 40 45 Frequency (Hz) -15 -20 -25 -30 -35 -40 -20 -30 -40 -50 - 60 0 200 400 600 Frequency (Hz) 800 1000 1200 Figure 50 ADC High Pass Filter Response, HPFAPP=0 Figure 51 ADC High Pass Filter Responses (48kHz), HPFAPP=1, all cut-off settings shown. 10 0 -10 Response (dB) 10 0 -10 -20 -30 -40 -50 -60 -20 Response (dB) -30 -40 -50 -60 -70 -80 0 200 400 600 Frequency (Hz) 800 1000 1200 -70 -80 -90 0 200 400 600 Frequency (Hz) 800 1000 1200 Figure 52 ADC High Pass Filter Responses (24kHz), HPFAPP=1, all cut-off settings shown. Figure 53 ADC High Pass Filter Responses (12kHz), HPFAPP=1, all cut-off settings shown. w PP, Rev 3.3, December 2007 90 Pre Production WM8941 NOTCH FILTERS AND LOW PASS FILTER The WM8941 supports four programmable notch filters. The fourth notch filter can be configured as a low pass filter. The following illustrates three digital notch filters, followed by a single low pass filter in the ADC filter path. Both the centre frequency and -3dB bandwidth are programmable for the notch filters. The cut off frequency is programmable for the low pass filter. The following graphs show the responses of 1) a single notch filter at three chosen centre frequencies, with three bandwidths for each, 2) the low pass filter at three chosen cut off frequencies and 3) the cascade of three notch filters followed by the low pass filter, each with a different centre / cut off frequency with three bandwidths for each. +0 -5 -10 -15 -20 -25 R E S P O N S E (dB) -30 -35 -40 -45 -50 -55 -60 20 50 100 200 500 1k Frequency (Hz) 2k 5k 10k 20k Figure 54 ADC Notch Filter Responses (48kHz); fc=100Hz, 1kHz, 10kHz; fb = 100Hz, 600Hz, 2kHz +0 -5 -10 R E S P O N S E -15 -20 -25 T (dB) -30 -35 -40 -45 -50 -55 -60 20 50 100 200 500 1k Frequency (Hz) 2k 5k 10k 20k Figure 55 ADC Low Pass Filter Responses (48kHz); fc= 1kHz, 5kHz, 10kHz w PP, Rev 3.3, December 2007 91 WM8941 +0 -5 R E S P O N S E (dB) -10 -15 -20 -25 -30 -35 -40 20 Pre Production T 50 100 200 500 1k Frequency (Hz) 2k 5k 10k 20k Figure 56 Cumulative Notch + Low Pass Filters Responses (48kHz); NF0 fc = 1kHz; NF1 fc = 5kHz; NF2 fc = 10kHz; LPF fc = 11kHz; fb = 100Hz, 600Hz, 2kHz Notch Filter Worked Example The following example illustrates how to calculate the a0 and a1 coefficients for a desired centre frequency and -3dB bandwidth. fc = 1000 Hz fb = 100 Hz fs = 48000 Hz w 0 = 2πfc / fs = 2π x (1000 / 48000) = 0.1308996939 rads w b = 2πfb / fs = 2π x (100 / 48000) = 0.01308996939 rads a0 = 1 − tan(0.0130899693 9 / 2) 1 − tan( w b / 2) = = 0.9869949627 1 + tan( w b / 2) 1 + tan( 0.0130899693 9 / 2) a1 = −(1 + a0 ) cos( w 0 ) = −(1 + 0.9869949627 ) cos(0.1308996939 ) = -1.969995945 NFn_A0 = -a0 x 213 = -8085 (rounded to nearest whole number) NFn_A1 = -a1 x 212 = 8069 (rounded to nearest whole number) These values are then converted to a 14-bit sign / magnitude notation: NFn_A0[13] = 1; NFn_A0[12:0] = 13’h1F95; NFn_A0 = 14’h3F95 = 14’b11111110010101 NFn_A1[13] = 0; NFn_A1[12:0] = 13’h1F85; NFn_A1 = 14’h1F85 = 14’b01111110000101 w PP, Rev 3.3, December 2007 92 Pre Production WM8941 APPLICATIONS INFORMATION RECOMMENDED EXTERNAL COMPONENTS Figure 57 Recommended External Components w PP, Rev 3.3, December 2007 93 WM8941 PACKAGE DIAGRAM FL: 28 PIN QFN PLASTIC PACKAGE 4 X 4 X 0.75 mm BODY, 0.45 mm LEAD PITCH DETAIL 1 D2 22 21 EXPOSED GROUND 6 PADDLE 28 D Pre Production DM042.B 1 4 E2 INDEX AREA (D/2 X E/2) E A SEE DETAIL 2 15 0.226 Ref. 14 e b 8 1 bbb M C A B 7 2X 2X aaa C aaa C TOP VIEW BOTTOM VIEW ccc C A3 A 0.08 C 5 DETAIL 1 DETAIL 2 45 degrees Datum L 1 C SEATING PLANE SIDE VIEW A1 DETAIL 2 0.30mm EXPOSED GROUND PADDLE e R Terminal tip e/2 A3 b Exposed lead G DETAIL 2 Symbols A A1 A3 b D D2 E E2 e G L MIN 0.70 0 0.175 3.95 2.55 3.95 2.55 0.375 Dimensions (mm) NOM MAX NOTE 0.75 0.80 0.02 0.05 0.203 REF 1 0.18 0.185 4.00 4.05 2.6 2.65 2 4.05 4.00 2 2.6 2.65 0.45 BSC 0.560 0.425 0.475 aaa bbb ccc REF: Tolerances of Form and Position 0.15 0.10 0.10 JEDEC, MO-220 NOTES: 1. DIMENSION b APPLIES TO METALLIZED TERMINAL AND IS MEASURED BETWEEN 0.15 mm AND 0.30 mm FROM TERMINAL TIP. 2. FALLS WITHIN JEDEC, MO-220. 3. ALL DIMENSIONS ARE IN MILLIMETRES. 4. THE TERMINAL #1 IDENTIFIER AND TERMINAL NUMBERING CONVENTION SHALL CONFORM TO JEDEC 95-1 SPP-002. 5. COPLANARITY APPLIES TO THE EXPOSED HEAT SINK SLUG AS WELL AS THE TERMINALS. 6. REFER TO APPLICATIONS NOTE WAN_0118 FOR FURTHER INFORMATION REGARDING PCB FOOTPRINTS AND QFN PACKAGE SOLDERING. 7. DEPENDING ON THE METHOD OF LEAD TERMINATION AT THE EDGE OF THE PACKAGE, PULL BACK (L1) MAY BE PRESENT. 8. THIS DRAWING IS SUBJECT TO CHANGE WITHOUT NOTICE. w PP, Rev 3.3, December 2007 94 Pre Production WM8941 IMPORTANT NOTICE W olfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer’s own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party’s products or services does not constitute Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS W olfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: sales@wolfsonmicro.com w PP, Rev 3.3, December 2007 95 WM8941 IMPORTANT NOTICE Pre Production W olfson Microelectronics plc (“Wolfson”) products and services are sold subject to Wolfson’s terms and conditions of sale, delivery and payment supplied at the time of order acknowledgement. Wolfson warrants performance of its products to the specifications in effect at the date of shipment. Wolfson reserves the right to make changes to its products and specifications or to discontinue any product or service without notice. Customers should therefore obtain the latest version of relevant information from Wolfson to verify that the information is current. Testing and other quality control techniques are utilised to the extent Wolfson deems necessary to support its warranty. Specific testing of all parameters of each device is not necessarily performed unless required by law or regulation. In order to minimise risks associated with customer applications, the customer must use adequate design and operating safeguards to minimise inherent or procedural hazards. Wolfson is not liable for applications assistance or customer product design. The customer is solely responsible for its selection and use of Wolfson products. Wolfson is not liable for such selection or use nor for use of any circuitry other than circuitry entirely embodied in a Wolfson product. Wolfson’s products are not intended for use in life support systems, appliances, nuclear systems or systems where malfunction can reasonably be expected to result in personal injury, death or severe property or environmental damage. Any use of products by the customer for such purposes is at the customer’s own risk. Wolfson does not grant any licence (express or implied) under any patent right, copyright, mask work right or other intellectual property right of Wolfson covering or relating to any combination, machine, or process in which its products or services might be or are used. Any provision or publication of any third party’s products or services does not constitute Wolfson’s approval, licence, warranty or endorsement thereof. Any third party trade marks contained in this document belong to the respective third party owner. Reproduction of information from Wolfson datasheets is permissible only if reproduction is without alteration and is accompanied by all associated copyright, proprietary and other notices (including this notice) and conditions. Wolfson is not liable for any unauthorised alteration of such information or for any reliance placed thereon. Any representations made, warranties given, and/or liabilities accepted by any person which differ from those contained in this datasheet or in Wolfson’s standard terms and conditions of sale, delivery and payment are made, given and/or accepted at that person’s own risk. Wolfson is not liable for any such representations, warranties or liabilities or for any reliance placed thereon by any person. ADDRESS W olfson Microelectronics plc Westfield House 26 Westfield Road Edinburgh EH11 2QB United Kingdom Tel :: +44 (0)131 272 7000 Fax :: +44 (0)131 272 7001 Email :: sales@wolfsonmicro.com w PP, Rev 3.3, December 2007 96
WM8941GEFLV 价格&库存

很抱歉,暂时无法提供与“WM8941GEFLV”相匹配的价格&库存,您可以联系我们找货

免费人工找货