AZ6962

AZ6962 10 AMP SUBMINIATURE POWER RELAY FEATURES • • • • • • • High sensitivity, 120 mW pickup Dielectric strength 5000 Vrms Isolation spacing greater than 10 mm Proof tracking index (PTI/CTI) 250 10 Amp switching capability Epoxy sealed version available Reinforced insulation, EN 60730-1 (VDE 0631, part 1) EN 60335-1 (VDE 0700, part 1) • UL, CUR file E43203 • VDE file 40010953 CONTACTS Arrangement Ratings SPDT (1 Form C), DPDT (2 Form C) SPST (1 Form A and 1 Form B) Resistive load: Max. switched power: 240 W or 2500 VA (2 Form C: 150 W or 1250 VA) Max. switched current: 10 A (2 Form C: 5 A) Max. switched voltage: 240* VDC or 440 VAC * Note: If switching voltage is greater than 30 VDC, GENERAL DATA Life Expectancy Mechanical Electrical Operate Time (typical) Release Time (typical) Minimum operations 3 x 107 1 x 105 at 8 A 250 VAC res. 7 ms at nominal coil voltage 3 ms at nominal coil voltage (with no coil suppression) special precautions must be taken. Please contact the factory. Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 2500 Vrms between contact sets 1000 Vrms between open contacts Insulation Resistance Insulation (according to DIN VDE 0110, IEC 60664-1) Dropout Ambient Temperature Operating Storage Vibration Shock Enclosure 1000 megohms min. at 20°C, 500 VDC, 50% RH C250 Overvoltage category: III Pollution degree: 3 Nominal voltage: 250 VAC Greater than 10% of nominal coil voltage At nominal coil voltage -40°C (-40°F) to 85°C (185°F) -40°C (-40°F) to 105°C (221°F) Break Contact: 5 g at 10 …500 Hz Make Contact: 20 g at 10…500 Hz 10 g P.B.T. polyester, UL94 V-O Tinned copper alloy, P.C. 270°C (518°F) 5 seconds 80°C (176°F) 30 seconds 8 grams 20 per plastic tube / 1000 per carton box Rated Load UL, CUR 10 A at 250 VAC resistive, 30k cycles [1], [2], [3] 10 A at 30 VDC resistive, 30k cycles [1], [2], [3] B300, R300 5 A at 250 VAC resistive, 30k cycles [1], [2], [3] (2 Form C) 8 A at 250 VAC resistive, 100k cycles [1], [2], [3] (1 Form A, 1 Form B and 1 Form C) Silver tin oxide [1] or silver nickel [2], gold plated silver nickel [3] available < 100 milliohms initially VDE Material Resistance COIL Power At Pickup Voltage (typical) Max. Continuous Dissipation Temperature Rise Temperature 120 mW (up to 24 VDC coil) 140 mW (48 VDC and 60 VDC coil) 1.2 W at 20°C (68°F) ambient Terminals Max. Solder Temp. Max. Solder Time 20°C (36°F) at nominal coil voltage Max. 130°C (266°F) Max. Solvent Temp. Max. Immersion Time Weight NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. Packing unit in pcs ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-07-28 Junkersstrasse 3, D-82178 Puchheim, Germany AZ6962 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC 5 6 9 12 15 18 24 48 60 Must Operate VDC 3.5 4.2 6.3 8.4 10.5 12.6 16.8 33.6 42.0 Max. Continuous VDC 11.6 14.0 20.8 27.2 31.0 39.4 53.1 98.0 122.4 Coil Resistance Ohm 113 ± 10% 164 ± 10% 360 ± 10% 620 ± 10% 800 ± 10% 1,295 ± 10% 2,350 ± 10% 8,000 ± 15% 12,500 ± 15% ORDER NUMBER* 1 Form A (SPST-NO) AZ6962–1AE–5D AZ6962–1AE–6D AZ6962–1AE–9D AZ6962–1AE–12D AZ6962–1AE–15D AZ6962–1AE–18D AZ6962–1AE–24D AZ6962–1AE–48D AZ6962–1AE–60D 1 Form C (SPDT) AZ6962–1CE–5D AZ6962–1CE–6D AZ6962–1CE–9D AZ6962–1CE–12D AZ6962–1CE–15D AZ6962–1CE–18D AZ6962–1CE–24D AZ6962–1CE–48D AZ6962–1CE–60D *Substitute “1B” in place of “1A” for Form B contacts. Suffix “E” at “1AE”, “1BE” or “1CE” indicates silver tin oxide contacts. Substitute suffix “B” in place of “E” at “1AE”, “1BE” or “1CE” for silver nickel contacts. Substitute “2C” in place of “1C” for 2 Form C relay. Add suffix “E” at the end of order number for sealed version. Add suffix “A” at the end of order number for gold plated contacts (at silver nickel only). MECHANICAL DATA FORM C VERSION 1.122 [28.5] .398 [10.1] FORM A and FORM B VERSION 1.122 [28.5] .398 [10.1] Coil Temperature Rise 160 150 140 130 120 110 100 90 80 70 60 50 40 30 20 10 0 .492 [12.5] .492 [12.5] .012 [0.3] .142 [3.6] .012 [0.3] .142 [3.6] 2 x ø .020 [ø 0.5] 3 x .016 [0.4] 3 x .031 [0.8] 2 x ø .020 [ø 0.5] 2 x .016 [0.4] 2 x .031 [0.8] Coil Temperature Rise °C 10A 0A 60% 8 0% 100% 120% 140% 160% 180% 200% 220% * * * * Not used on 1 Form C relay Percent of Nominal Coil Voltage at 20°C PC BOARD LAYOUT 5 x ø .051 [ø 1.3] .870 [22.1] .062 [1.57] CIRCUIT DIAGRAM 1 .050 [1.3] 4 Maximum Switching Capacity (1 Form A, 1 Form B and 1 Form C) .298 [7.56] 1 FORM C 1 FORM C .126 [3.2] .126 [3.2] 2 1 3 3 5 10.0 9.0 8.0 7.0 6.0 5.0 4.0 3.0 4 x ø .051 [ø 1.3] .744 [18.9] .116 [2.95] 1 FORM A DC Resistive Load CURRENT .298 [7.56] 1 FORM A 1 FORM B .198 [5.04] .050 [1.3] 2 1 3 4 2.0 AC Resistive Load 1 FORM B .062 [1.57] 2 1 8 7 4 6 1.0 .9 .8 .7 .6 .5 8 x ø .051 [ø 1.3] .744 [18.9] .4 .3 .2 .298 [7.56] 2 FORM C .050 [1.3] 2 FORM C 10 100 .126 [3.2] .126 [3.2] VIEWED TOWARD TERMINALS VIEWED TOWARD TERMINALS VOLTAGE Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" ZETTLER electronics GmbH Tel. +49 89 800 97 0 Fax +49 89 800 97 200 office@ZETTLERelectronics.com www.ZETTLERelectronics.com 2004-07-28 Junkersstrasse 3, D-82178 Puchheim, Germany 1000 20 30 40 50 60 70 80 90 200 300 400 500 600 700 800 900 2 3 4 5 .1