Z8051™ Family of 8-Bit Microcontrollers
Z51F0410 Evaluation Kit
User Manual
UM025704-0413
Copyright ©2013 Zilog®, Inc. All rights reserved.
www.zilog.com
Z51F0410 Evaluation Kit
User Manual
ii
Warning: DO NOT USE THIS PRODUCT IN LIFE SUPPORT SYSTEMS.
LIFE SUPPORT POLICY
ZILOG’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE
SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS PRIOR WRITTEN APPROVAL OF
THE PRESIDENT AND GENERAL COUNSEL OF ZILOG CORPORATION.
As used herein
Life support devices or systems are devices which (a) are intended for surgical implant into the body, or (b)
support or sustain life and whose failure to perform when properly used in accordance with instructions for
use provided in the labeling can be reasonably expected to result in a significant injury to the user. A critical component is any component in a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system or to affect its safety or effectiveness.
Document Disclaimer
©2013 Zilog, Inc. All rights reserved. Information in this publication concerning the devices, applications,
or technology described is intended to suggest possible uses and may be superseded. ZILOG, INC. DOES
NOT ASSUME LIABILITY FOR OR PROVIDE A REPRESENTATION OF ACCURACY OF THE
INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED IN THIS DOCUMENT. ZILOG ALSO
DOES NOT ASSUME LIABILITY FOR INTELLECTUAL PROPERTY INFRINGEMENT RELATED
IN ANY MANNER TO USE OF INFORMATION, DEVICES, OR TECHNOLOGY DESCRIBED
HEREIN OR OTHERWISE. The information contained within this document has been verified according
to the general principles of electrical and mechanical engineering.
Z8051 is a trademark or registered trademark of Zilog, Inc. All other product or service names are the
property of their respective owners.
UM025704-0413
Z51F0410 Evaluation Kit
User Manual
iii
Revision History
Each instance in the Revision History table below reflects a change to this document from
its previous version.
Revision
Level
Description
Page
Apr
2013
04
Updated schematic diagrams.
37, 38
Dec
2012
03
Corrected Figures 5 and 7.
7,9
Dec
2012
02
Corrected formatting issue in Table 2.
16
Nov
2012
01
Original issue.
All
Date
UM025704-0413
Revision History
Z51F0410 Evaluation Kit
User Manual
iv
Table of Contents
Revision History . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .iii
List of Figures . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . v
List of Tables. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . vii
Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Install the Z8051 OCD Software and Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Configure the Z8051 OCD and Z51F0410 Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . 15
Build and Run the Z51F0410 Demo Project. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18
Sample Projects and Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36
Appendix A. Schematic Diagrams . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Appendix B. OCD Driver Installation on Windows Vista Systems . . . . . . . . . . . . . . . . . . . . . 39
Appendix C. OCD Driver Installation on Windows XP Systems. . . . . . . . . . . . . . . . . . . . . . . 42
Appendix D. Stand-Alone Flash Programming Using the Keil µVision IDE . . . . . . . . . . . . . 45
Customer Support . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
UM025704-0413
Table of Contents
Z51F0410 Evaluation Kit
User Manual
v
List of Figures
Figure 1.
The Z51F0410 Evaluation Kit . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Figure 2.
Z51F0410 Evaluation Board . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Figure 3.
Block Diagram of the Z51F0410 Evaluation Board . . . . . . . . . . . . . . . . . . . 3
Figure 4.
Install Device Driver Dialog, Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Figure 5.
Browse For Driver Dialog, Windows Vista . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Figure 6.
Can’t Verify Publisher Dialog, Windows Vista . . . . . . . . . . . . . . . . . . . . . . 8
Figure 7.
Successfully Installed Dialog, Windows Vista . . . . . . . . . . . . . . . . . . . . . . . 9
Figure 8.
Unsuccessful Installation, Scenario 1 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10
Figure 9.
Unsuccessful Installation, Scenario 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Figure 10. Device Manager Dialog, Windows 7 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Figure 11. A Successful USB-to-UART Driver Installation . . . . . . . . . . . . . . . . . . . . . 14
Figure 12. Connecting the 10-Circuit Cable to the Board . . . . . . . . . . . . . . . . . . . . . . . 15
Figure 13. Connecting the Evaluation Board's P1 Port to the USB Port . . . . . . . . . . . 16
Figure 14. An Example Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 17
Figure 15. Initial OCD Screen . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19
Figure 16. Object File Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
Figure 17. Configuration Dialog . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21
Figure 18. A Typical On-Chip Debugger Window . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Figure 19. A Typical On-Chip Debugger with Child Windows Open . . . . . . . . . . . . . 23
Figure 20. Reset Toolbar Icon . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Figure 21. HyperTerminal Message After Selecting Go . . . . . . . . . . . . . . . . . . . . . . . . 24
Figure 22. Z51F0410 Demo Program . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Figure 23. Selecting the Demo Project File . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
Figure 24. Selecting the Target . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28
Figure 25. Selecting the Target Driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 29
Figure 26. Configuring the Debug Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30
Figure 27. Configuring the Flash Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
Figure 28. Load Application at Startup Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31
UM025704-0413
List of Figures
Z51F0410 Evaluation Kit
User Manual
vi
Figure 29. Beginning a Debug Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 30. A Default Debug Session . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
Figure 31. Demo Program Menu in HyperTerminal . . . . . . . . . . . . . . . . . . . . . . . . . . . 35
Figure 32. Z51F0410 Evaluation Board, #1 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 37
Figure 33. Z51F0410 Evaluation Board, #2 of 2 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
Figure 34. Found New Hardware Dialog, Windows Vista . . . . . . . . . . . . . . . . . . . . . . 39
Figure 35. Install Device Driver Dialog, Windows Vista . . . . . . . . . . . . . . . . . . . . . . . 40
Figure 36. Couldn’t Find Driver Dialog, Windows Vista . . . . . . . . . . . . . . . . . . . . . . . 41
Figure 37. The Found New Hardware Wizard Welcome Screen . . . . . . . . . . . . . . . . . 42
Figure 38. The Found New Hardware Wizard’s Browse Screen . . . . . . . . . . . . . . . . . 43
Figure 39. Selecting A Target Driver For Flash Programming . . . . . . . . . . . . . . . . . . . 45
Figure 40. Configuring Additional Flash Options . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
Figure 41. The Keil IDE Flash Menu . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46
UM025704-0413
List of Figures
Z51F0410 Evaluation Kit
User Manual
vii
List of Tables
Table 1.
Z51F0410000KITG Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2
Table 2.
Jumper Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16
Table 3.
Z51F0410 Evaluation Kit Sample Projects . . . . . . . . . . . . . . . . . . . . . . . . . 36
Table 4.
Z51F0410 Evaluation Kit Documentation . . . . . . . . . . . . . . . . . . . . . . . . . . 36
UM025704-0413
List of Tables
Z51F0410 Evaluation Kit
User Manual
1
Introduction
This manual describes how to set up Zilog’s Z51F0410 Evaluation Kit (Zilog part number
Z51F0410000KITG) and use it to evaluate your Z8051-based designs and applications.
The Kit features a small Evaluation Board consisting of two LEDs, two pushbuttons, port
pin headers and a USB port. The Board features the Z51F0410 MCU in a 10-pin SSOP
package, plus a DBG connector to connect the board to a host development PC using the
Z8051 USB On-Chip Debugger (OCD) cable. For more details about the Z51F0410 MCU,
please refer to the Z51F0410 Product Specification (PS0295).
This document guides you through the following tasks:
•
•
•
Install the Z8051 OCD Software and Documentation – see page 5
Configure the Z8051 OCD and Z51F0410 Evaluation Board – see page 15
Build and Run the Z51F0410 Demo Project – see page 18
Figure 1 displays an image of the Z51F0410 Evaluation Kit.
Figure 1. The Z51F0410 Evaluation Kit
UM025704-0413
Introduction
Z51F0410 Evaluation Kit
User Manual
2
Kit Contents
Table 1 lists the contents of the Z51F0410 Evaluation Kit.
Table 1. Z51F0410000KITG Contents
Item
Description
Quantity
1
Z51F0410 Evaluation Board
1
2
Z8051 USB On-Chip Debugger (OCD)
1
3
Z8051 OCD Target Cable (10ckt)
1
4
USB Cable: A (male) to Mini-B
1
5
Z51F0410 Evaluation Kit Insert (FL0148)
1
Figure 2 displays an image of the Z51F0410 Evaluation Board.
Figure 2. Z51F0410 Evaluation Board
Supported Operating Systems
The Z51F0410 Evaluation Board and the Z8051 On-Chip Debugger support the following
operating systems:
•
•
•
UM025704-0413
Microsoft Windows XP
Microsoft Windows Vista (32-bit/64-bit)
Microsoft Windows 7 (32-bit/64-bit)
Introduction
Z51F0410 Evaluation Kit
User Manual
3
Z51F0410 Evaluation Board Block Diagram
Figure 3 displays a block diagram of the Z51F0410 Evaluation Board.
Figure 3. Block Diagram of the Z51F0410 Evaluation Board
Z51F0410 Evaluation Board Description
The Z51F0410 Evaluation Board contains the following components:
•
•
•
•
Z51F0410: U2, 10-pin SSOP chip
•
•
•
•
USB connector: P1
UM025704-0413
1 green LED (D2) is connected to the GPIO pin of the Z51F0410 MCU
1 green LED (D1) to indicate USB power
2 pushbuttons:
– SW1: RESET
– SW2 is connected to the GPIO pin on the Z51F0410 MCU
OCD connector: J4, J3
USB to UART interface: U1
USB interface provides power and communication to the Board
Introduction
Z51F0410 Evaluation Kit
User Manual
4
•
Test points J1 and J2 are connected to Ground; J7–J14 are connected to GPIO pin of
U2
When the Board is connected to the USB port of the host PC, the green D1 LED will illuminate (turn ON).
Schematic diagrams of the Z51F0410 Evaluation Board are presented on pages 37 through
38 of this document.
The physical dimensions of the Board are: 1.75" x 0.75" (44.4 mm x 19 mm).
UM025704-0413
Introduction
Z51F0410 Evaluation Kit
User Manual
5
Install the Z8051 OCD Software and
Documentation
The Z8051 On-Chip Debugger (OCD) interface is the interface by which your PC will
communicate with the Z51F0410 MCU to download and execute code. In addition to the
OCD, software such as development tools and sample applications will be installed.
Supported Operating Systems
The Software and Documentation for this reference design supports Microsoft Windows 7
(32-bit/64-bit), Windows Vista (32-bit/64-bit) and Windows XP.
Note: If you have already downloaded the Z8051 software and documentation from the Zilog
Store and installed it following the procedure on the paper insert in your kit (FL0148), skip
this section and proceed to the Z8051 OCD Driver Installation section, below.
Observe the following procedure to install the Z8051 On-Chip Debugger software and
documentation on your computer.
1. Ensure that the OCD interface hardware is not connected to your PC.
2. In a web browser, download the Z8051 Software and Documentation v2.1 or later
from the Zilog Store. When the download is complete, unzip the file to your hard
drive and double-click to launch the installation file named Z8051_.exe.
3. From the main menu, select Go to the installation page, then select one of the following options:
– If you do not plan to use the Keil µVision4 IDE, select Zilog OCD + Samples +
SDCC.
– If you will be using the Keil µVision4 IDE, select Zilog OCD + Samples + Keil
µVision4 IDE Debugging Support.
– If you only plan to use the programming features and do not plan to perform any
development, select Zilog OCD.
– To install all files, select All of the above.
Note: In this filename, refers to the version number of the OCD Software
and Documentation release. For example, this version number may be 2.1.
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
6
4. Follow the on-screen instructions to complete the OCD software installation.
Z8051 OCD Driver Installation
The driver programs for the Z8051 On-Chip Debugger are copied during the software and
documentation installation. In the following procedure for PCs running Windows 7 32and 64-bit operating systems, ensure that the target side of the OCD will remain unconnected while you install these drivers.
Note: If you are running Windows Vista, see Appendix B. on page 39 to install your device drivers. If you are running Windows XP, see Appendix C. on page 42.
1. Connect the OCD hardware to the USB port of your PC by connecting the A (male)
end of the USB A (male)-to-Mini-B cable with the host PC’s USB port. Connect the
Mini-B end to the OCD device.
2. After the PC detects the new hardware, it will display the Installing device driver software dialog shown in Figure 4.
Figure 4. Install Device Driver Dialog, Windows 7
IMPORTANT NOTE: If you should encounter the scenarios presented in Figures 8 or 9, right-click your
mouse on ZILOG OCD I/F (highlighted in Figure 8) or Unknown device (highlighted in Figure 9) and
select Update Driver Software...
3. Select Browse my computer for driver software (advanced) to display the dialog
shown in Figure 5, which prompts you to key in or browse for the location of the .inf
file. Depending on the type of computer you use (32- bit or 64-bit), use the Browse
button to navigate to one of the following paths, then click the Next button.
– On 32-bit machines, use the following path:
\Z8051_\device drivers\OCD USB\x32
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
7
–
On 64-bit machines, use the following path:
\Z8051_\device drivers\OCD USB\x64
Note: In the above filepaths, refers to C:\Program Files\zilog.
Figure 5. Browse For Driver Dialog, Windows Vista
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
8
4. When Windows prompts you whether to install or not install, as shown in Figure 6,
click Install this driver software anyway and wait until the installation is completed
(Windows may prompt you more than once).
Figure 6. Can’t Verify Publisher Dialog, Windows Vista
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
9
5. When the installation is complete, the screen shown in Figure 7 will appear. Click
Close to exit the OCD driver installation.
Figure 7. Successfully Installed Dialog, Windows Vista
Note: On some installations, the Found New Hardware screen shown in Figure 7 may also display the text string, Zilog Z8051 USB OCD - No Firmware. This occurrence is normal
and can be disregarded.
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
10
Figure 8. Unsuccessful Installation, Scenario 1
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
11
Figure 9. Unsuccessful Installation, Scenario 2
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
12
6. If Zilog Z8051 USB OCD appears in the Device Manager (as highlighted in
Figure 10), the OCD driver software has been successfully installed.
Figure 10. Device Manager Dialog, Windows 7
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
13
FTDI USB-to-UART Driver Installation
An FTDI USB-to-UART driver is required to allow your PC to communicate through its
USB port to the on-chip UART of the Z51F0410 MCU. Observe the following procedure
to perform these connections.
1. Ensure that the Z51F0410 Evaluation Board’s P1 connector is not plugged in to the
host PC’s USB port.
2. Navigate to the following filepath and double-click the CDM20802_setup.exe file to
begin the driver installation.
\Z8051_\device drivers\FTDI Uart
3. The installation process will begin and you should observe output similar to the following messages on the screen of your PC:
32-bit OS detected
\dpinstx86.exe
Installation driver
FTDI CDM driver installation process completed.
Note: The above message may appear for a short time, but will then disappear from your window.
This occurrence is normal.
4. When the installation is complete, plug in the Board’s P1 connector into the USB port
of your PC. Refer to Figure 13 on page 16 for guidance.
5. If the driver installation was successful, the Ports (COM & LPT) section of the Device
Manager will display USB Serial Port (COMx) or similar message, as highlighted in
Figure 11.
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
14
Figure 11. A Successful USB-to-UART Driver Installation
Note: 1. To launch the Device Manager on Windows 7 systems, launch the Start menu, enter
device manager in the Search programs and files field, and press the Enter key.
2. To open the Device manager on earlier Windows systems, navigate via the following
path:
Start → Control Panel → System → Hardware → Device Manager → Ports (COM&
LPT)
UM025704-0413
Install the Z8051 OCD Software and Documentation
Z51F0410 Evaluation Kit
User Manual
15
Configure the Z8051 OCD and Z51F0410
Evaluation Board
Observe the following procedure to set up and configure the Z8051 On-Chip Debugger
and the Z51F0410 Board.
Caution: Steps number 1 to 4 present the power-up sequence. Carefully follow these steps
to avoid encountering an improper connection or disconnection.
1. Connect the Z8051 On-Chip Debugger (OCD) to the host PC’s USB port.
2. Connect one end of the 10-circuit cable to the Z8051 OCD.
3. Connect the other end of the 10-circuit cable connector to the Z51F0410 Board’s J4
and J3 connectors. Pin 1 of the cable connector is indicated by a red stripe, as shown
in Figure 12.
Figure 12. Connecting the 10-Circuit Cable to the Board
4. Set the jumpers as indicated in Table 2.
UM025704-0413
Configure the Z8051 OCD and Z51F0410 Evaluation
Z51F0410 Evaluation Kit
User Manual
16
Table 2. Jumper Settings
Jumper
Description
TxD
J5
RxD
J6
D2 LED
State
Function
Factory Setting
1–2
TxD_0
IN
3–4
TxD_1
5–6
RxD_0
7–8
RxD_1
1–2
DSDA
2–3
RxD_1
IN
IN
5. Connect P1 on the Z51F0410 Board to the host PC’s USB port to apply power to the
Board, as shown in Figure 13.
Notes: 1. Upon applying power, the green LED (D1) will be illuminated.
2. When recycling power, Zilog recommends waiting for at least 5 seconds before reapplying power to allow a proper power-on reset.
Figure 13. Connecting the Evaluation Board's P1 Port to the USB Port
UM025704-0413
Configure the Z8051 OCD and Z51F0410 Evaluation
Z51F0410 Evaluation Kit
User Manual
17
Figure 14 shows an example of a completed hardware and software setup.
Figure 14. An Example Setup
UM025704-0413
Configure the Z8051 OCD and Z51F0410 Evaluation
Z51F0410 Evaluation Kit
User Manual
18
Build and Run the Z51F0410 Demo
Project
Observe the following procedure to build and run the Z51F0410 demo project.
Note: If you plan to use the Keil µVision IDE, please skip to the Using the Keil µVision IDE on a
Demo Project section on page 25.
1. Browse to the following location and double-click the build_sdcc.bat batch file to
build the project:
\Z8051_\samples\Z51F0410\Demo\build_sdcc.bat
Note: Refer to the Z8051 Tools Product User Guide (PUG0033) for additional information about
these project files and Small Device C Compiler (SDCC) development tools.
2. When the build is complete, the command window will prompt the user to press any
key to continue. Proceed by pressing any key on your keyboard; as a result, a hex file
for the demo will be created in the following path:
\Z8051_\samples\Z51F0410\Demo\demo.hex
3. Set up the OCD and Evaluation Board. If you have not already configured these items,
please return to the Configure the Z8051 OCD and Z51F0410 Evaluation Board section on page 15.
4. Run the Z8051 OCD software. From the Start menu, navigate to All Programs →
Zilog Z8051 SW and Docs → Zilog Z8051 OCD
. Once launched, the program will display Connected, as shown
in Figure 15.
Note: If you encounter a message that says Disconnected, return to the Configure the Z8051
OCD and Z51F0410 Evaluation Board section on page 15 to configure the proper powerup sequence. If the problem persists, Zilog recommends that you review the Z8051 OCD
Driver Installation and FTDI USB-to-UART Driver Installation sections.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
19
Figure 15. Initial OCD Screen
Note: For a free download of the latest version of the OCD software, visit the Zilog website and
navigate via the Tools and Software menu to Software Downloads.
5. In the Debugger window, select Load Hex from the File menu to display the Object
File dialog, which is shown in Figure 16.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
20
Figure 16. Object File Dialog
6. In the Object file dialog, browse to the hex file that you created in Step 2 and click
Open.
7. Click the Download button to open the Configuration dialog box, shown in Figure 17.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
21
Figure 17. Configuration Dialog
8. Click the Write button to open the On-Chip Debugger’s main window. A typical OCD
display is shown in Figure 18; Figure 19 shows an OCD window with child windows
open.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
22
Figure 18. A Typical On-Chip Debugger Window
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
23
Figure 19. A Typical On-Chip Debugger with Child Windows Open
Note: Use the View menu to open the child windows. For this demonstration, the example windows shown in Figure 19 do not need to be opened.
9. Click the Reset toolbar icon of the OCD software, which is shown in Figure 20.
Figure 20. Reset Toolbar Icon
10. Open HyperTerminal. Next, select the appropriate COM port and set it to 9600 8-N-1.
11. From the Emulation menu of the OCD software, select Go. As a result, you should
see the HyperTerminal message shown in Figure 21.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
24
Figure 21. HyperTerminal Message After Selecting Go
12. Disconnect the OCD 10-ckt cable from the Evaluation Board.
13. Unplug the Evaluation Board from the PC.
14. Disconnect the HyperTerminal connection.
15. Plug the Evaluation Board into the PC’s USB port.
16. Reestablish a HyperTerminal connection by clicking the Call button.
17. Press any key on the active HyperTerminal window; see Figure 22.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
25
Figure 22. Z51F0410 Demo Program
18. Press SW2 on the Evaluation Board, or key in a 1 in the active HyperTerminal window to start/stop the blinking of LED D2.
Note: Similar projects that you can use as references are listed in Table 3 on page 36.
Using the Keil µVision IDE on a Demo Project
Zilog’s On-Chip Debugger hardware now fully supports the Keil µVision IDE. Our target
driver is seamlessly integrated with the Keil debugger, allowing Keil C51 users to work
within the µVision4 environment without switching between the Keil compiler and
Zilog’s external OCD software. In the demo project example that follows, the Z51F0410
MCU-related project is referenced as Demo.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
26
Notes: 1. This document refers to the Keil µVision IDE V4.53.0.6 (PK51 Prof. Developers Kit)
or later.
2. Refer to the Z8051 Tools Product User Guide (PUG0033) for additional information
about these project files and debugging with the Keil µVision IDE and Zilog On-Chip
Debugger.
Debugger Configuration
Observe the following procedure to build and run a Z51F0410 demonstration project using
the Keil µVision IDE.
1. Start the Keil µVsion4 IDE.
2. From the Project menu, select Open Project and navigate to the following filepath:
\Z8051_\samples\Z51F0410\Demo
3. Select the Demo.uvproj file and click Open; see Figure 23.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
27
Figure 23. Selecting the Demo Project File
4. Return to the Project menu and select Options for Target ‘Demo’.
5. In the Options for Target ‘Demo’ dialog that appears, click the Device tab and ensure
that your target is properly selected for your project, as illustrated in Figure 24.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
28
Figure 24. Selecting the Target
6. After selecting the target, click the Debug tab and select the Zilog Z8051 Target
Driver from the Use: drop-down menu, as highlighted in Figure 25.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
29
Figure 25. Selecting the Target Driver
7. Click the Settings button, located to the right of this drop-down menu, to configure
your Debug and Flash options. The Settings dialog is displayed with the Debug
Options tab appearing by default, as shown in Figure 26.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
30
Figure 26. Configuring the Debug Options
Notes: 1. When configuring the appropriate Debug option, be aware of the following stipulations:
•
Checking the Peripheral continues running option means that the timers used in
your project will run while the processor is stopped by the debugger.
•
The Reset at Main option will only work if you have a main file in your project; otherwise you should deselect this option.
2.
3. Click the Flash Options tab. The Flash Options Settings dialog will appear, as shown
in Figure 27. To select the proper options for Flash programming, refer to the
Z51F0410 Product Specification (PS0295).
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
31
Figure 27. Configuring the Flash Options
4. Click OK to exit the Settings dialog.
5. From the Options for Target ‘Demo’ dialog, select the Load Application at Startup
checkbox, as shown in Figure 28, the so that the IDE will download the code upon
connection. There is no need to select or enter an initialization file.
Figure 28. Load Application at Startup Settings
6. Click OK to exit the Options for Target ‘Demo’ dialog.
7. From the Project menu, select Rebuild All to rebuild all target files.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
32
8. Start your debugging session by clicking the Start/Stop Debug Session icon, as indicated in Figure 29. A default Windows configuration of the debug session is shown in
Figure 30.
Figure 29. Beginning a Debug Session
Figure 30. A Default Debug Session
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
33
Note: 1. The following buttons in the Keil µVision IDE are not supported by the Zilog OCD
driver:
2. To learn more about the full functionality of the Keil µVision IDE, please refer to the
Keil Keil µVision4 IDE documentation.
3. From the Debug menu, select Reset CPU.
4. From the Debug menu, select Run. As a result, you should see the HyperTerminal
message shown in Figure 21 on page 24.
5. Disconnect the OCD 10-ckt cable from the Evaluation Board.
6. Unplug the Evaluation Board from the PC.
7. Disconnect the HyperTerminal connection.
8. Plug the Evaluation Board into the PC’s USB port.
9. Reestablish a HyperTerminal connection by clicking the Call button.
10. Press any key on the active HyperTerminal window; see Figure 22 on page 25.
11. Press SW2 on the Evaluation Board, or key in a 1 in the active HyperTerminal window to start/stop the blinking of LED D2.
12. To stop your debugging session, click the Start/Stop Debug Session icon.
Note: Refer to Appendix D. on page 45 for a discussion of Stand-Alone Flash Programming
Using the Keil µVision IDE.
HyperTerminal Configuration
A communications program such as HyperTerminal can be used on Windows XP systems
to view the messages from the Z51F0410 Evaluation Board. The following procedure
examines how to configure HyperTerminal for the Z51F0410 demo project.
Note: The HyperTerminal application is not available in Windows Vista and Windows 7 systems.
If you are using either of these operating systems, consider using/installing different com-
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
34
munication software, such as Tera Term. Please refer to the documentation for the particular emulation software you use to configure it for communication with the Z51F0410
Evaluation Board.
1. In HyperTerminal, select the COM port assigned to the USB-to-UART interface cable
that is connected to the P1 connector on the Evaluation Board.
Note: This COM port can be determined from the Device Manager, as described in the the FTDI
USB-to-UART Driver Installation section on page 13.
2. Configure this port to reflect the following settings:
– 9600 bps
– 8 data bits
– No parity
– 1 stop bit
– No flow control
3. Click the Call button to connect to the Z51F0410 Board. Upon connection, you should
be able to see the Demo program menu shown in Figure 31.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
35
Figure 31. Demo Program Menu in HyperTerminal
At this point, you have successfully run the Z51F0410 demo project, but you are welcome
to continue evaluating the demo in HyperTerminal. For additional information about how
to create, edit, run and debug this project, please see the Z8051 Tools Product User Guide
(PUG0033) and/or the Z8051 On-Chip Debugger and In-System Programmer User Manual (UM0240).
Note: Turn off the power by removing the USB cable from the P1 connector on the Evaluation
Board.
UM025704-0413
Build and Run the Z51F0410 Demo Project
Z51F0410 Evaluation Kit
User Manual
36
Sample Projects and Documentation
A number of sample projects are included with the Z51F0410 Evaluation Kit installation
software, and their locations, listed in Table 3, will be accessible upon installation.
Table 3. Z51F0410 Evaluation Kit Sample Projects
Description
Location
Demo
samples\Z51F0410\Demo
Led Blink
samples\Z51F0410\Led_Blink
samples\Z51F0410\Led_Blink_Asm
A number of Z8051-related documents are included in the Z51F0410 Evaluation Kit, and
their locations, listed in Table 4, will be accessible upon installation. You can also find
current versions of each of these documents on the Zilog website.
Table 4. Z51F0410 Evaluation Kit Documentation
Description
Document
Location
Z51F0410 Product Specification
PS0295
Documentation\Chip_Documentation
Z51F0811 Product Specification
PS0296
Documentation\Chip_Documentation
Z51F3220 Product Specification
PS0299
Documentation\Chip_Documentation
Z51F3221 Product Specification
PS0300
Documentation\Chip_Documentation
Z51F6412 Product Specification
PS0303
Documentation\Chip_Documentation
Z51F0410 Product Brief
PB0237
Documentation\Chip_Documentation
Z51F0811 Product Brief
PB0238
Documentation\Chip_Documentation
Z51F3220 Product Brief
PB0239
Documentation\Chip_Documentation
Z51F3221 Product Brief
PB0240
Documentation\Chip_Documentation
Z51F6412 Product Brief
PB0241
Documentation\Chip_Documentation
Z8051 OCD and ISP User Manual
UM0240
Documentation\Tools_Documentation
Z51F0410 Evaluation Kit User Manual
UM0257
Documentation\Tools_Documentation
Z51F0811 Evaluation Kit User Manual
UM0242
Documentation\Tools_Documentation
Z51F3220 Development Kit User Manual
UM0243
Documentation\Tools_Documentation
Z51F3221 Development Kit User Manual
UM0258
Documentation\Tools_Documentation
Z51F6412 Development Kit User Manual
UM0259
Documentation\Tools_Documentation
Z8051 Tools Product User Guide
PUG0033
Documentation\Tools_Documentation
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
37
Appendix A. Schematic Diagrams
Figures 32 and 33 show schematic diagrams of the Z51F0410 Evaluation Board.
VCC_5V
D1
R1
1
2
GREEN
470 ohm
L1
FERRITE BEAD
C1
C2
4.7uF
0.1uF
P1
R3
20.0K
C3
10nF
USB TYPE A PLUG
U1
27
28
17
C4
CTS
USBDP
DTR
NC1
DSR
RESET
DCD
NC
RI
OSCI
CBUS0
OSCO
CBUS1
CBUS2
3v3 OUT
25
0.1uF
USBDM
CBUS3
TEST
100K
24
RTS
GND3
19
RXD
26
8
R4
VCC
GND2
15
TXD
21
16
VCCIO
GND1
4
20
18
Shield1
Shield2
R2
4.75K
AGND
5
6
1
2
3
4
7
1
2
3
4
CBUS4
1
RxD
5
TxD
RxD
TxD
3
11
2
9
10
6
23
J1
J2
22
1
1
13
HDR/PIN 1x1
HDR/PIN 1x1
14
12
FT232RL
Figure 32. Z51F0410 Evaluation Board, #1 of 2
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
38
C5
VCC_5V
VCC_5V
0.1uF
R5
10K
J3
1
2
3
4
5
1
3
5
7
9
R6
10K
J7
1
J4
J8
1
1
2
3
4
5
J9
1
DSCL
DSDA_LED
J10
VCC_5V
RxD_0
TxD_0
RESET
RxD_1
U2
1
2
3
4
5
VDD
P00/RXD/AN0/XIN(SUBXIN)
P01/TXD/INT1/AN1/XOUT(SUBXOUT)
P02/ACK/AN2/RESETB
P06/AN6
VSS
(DSDA)/AC+/AN5/BUZ/PWM1O/SDA/P05
AVref/AC-/AN4/T0O/SCL/P04
(DSCL)/ACOUT/AN3/EC0/SS/INT0/P03
AN7/P07
10
9
8
7
6
DSDA_LED
DSCL
TxD_1
C6
DSCL
0.1uF
Z51F0410
2
4
6
8
10
UART CONNECTIONS
J5
TxD_0
1 2
TxD_1
3 4
RxD_0
5 6
RxD_1
7 8
TxD
TxD
RxD
RxD
J11
1
J12
1
TxD_1
1
1
1
J13
J14
VCC_5V
R7
HDR/PIN 2x4
499K
VCC_5V
RESET
DSDA_LED
J6
R9
2
470 ohm
D2
GREEN
1
LED
Pin 6
1
2
3
1
2
SW1
B3U-1000P
R10
C7
499K
0.01uF
TIMER/LED CONNECTION
RxD_1
PIN #
1-2
5-6
3-4
7-8
1-2
SHUNTS FUNCTIONS AND SETTINGS
J5 UART CONNECTIONS
SIGNAL
PINMCR SETTING, 0X0092
TxD_0
USART_CFG = 0
RxD_0
USART_CFG = 0
TxD_1
USART_CFG = 1
RxD_1
USART_CFG = 1
J6 TIMER/LED CONNECTION
DSDA_LED
TR_CFG = 0
R8
VCC_5V
49.9K
DSCL
1
2
SW2
B3U-1000P
Figure 33. Z51F0410 Evaluation Board, #2 of 2
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
39
Appendix B. OCD Driver Installation on
Windows Vista Systems
The driver programs for the Z8051 On-Chip Debugger are copied to the development PC
during the software and documentation installation. In the following procedure for PCs
running Windows Vista 32- and 64-bit operating systems, ensure that the target side of the
OCD will remain unconnected while you install these drivers.
1. Connect the OCD hardware to the USB port of your PC by connecting the A (male)
end of the USB A (male)-to-Mini-B cables with the development PC’s USB port.
Connect the Mini-B end to the OCD device.
2. After the PC detects the new hardware, it will display the Found New Hardware Wizard dialog box, shown in Figure 34. Click Locate and install driver software (recommended).
Figure 34. Found New Hardware Dialog, Windows Vista
3. Depending on your development PC’s User Account Control settings, Windows may
ask for permission to continue the installation. Click Continue.
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
40
4. When the Insert the Disc dialog appears, as shown in Figure 35, select I don’t have
the disc. Show me other options. Click the Next button to display the dialog that
follows, which is shown in Figure 36.
Figure 35. Install Device Driver Dialog, Windows Vista
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
41
Figure 36. Couldn’t Find Driver Dialog, Windows Vista
5. Return to page 6 and follow Steps 3 through 6.
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
42
Appendix C. OCD Driver Installation on
Windows XP Systems
The driver programs for the Z8051 On-Chip Debugger are copied during the software and
documentation installation. On Windows XP systems, ensure that the target side of the
OCD will remain unconnected while you install these drivers. It is important that you
observe the following procedure; do not skip ahead until the OCD drivers are installed.
1. Connect the OCD hardware to the USB port of your PC by connecting the A-Male end
of the USB A (male)-to-Mini-B cables with the host PC’s USB port, and connect the
Mini-B end to the OCD device.
2. After the PC detects the new hardware, it will display the Found New Hardware Wizard dialog box, shown in Figure 37. Select Install from a list or specific location
(Advanced); then click Next.
Figure 37. The Found New Hardware Wizard Welcome Screen
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
43
3. The next dialog box, shown in Figure 38, prompts you to enter a path or navigate to
the directory in which the .inf file was installed. Depending on the type of computer
you use (32- bit or 64-bit), use the Browse button to navigate to one of the following
paths and click the Next button, leaving all other selections at their default settings.
– On 32-bit machines, use the following path:
\Z8051_\device drivers\OCD USB\x32
–
On 64-bit machines, use the following path:
\Z8051_\device drivers\OCD USB\x64
Note: On some installations, the Found New Hardware screen shown in Figure 37 may also display the text string, Zilog Z8051 USB OCD - No Firmware. This occurrence is normal
and can be disregarded.
Figure 38. The Found New Hardware Wizard’s Browse Screen
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
44
4. When Windows prompts you whether to continue the installation or stop, click the
Continue Anyway button and wait until the installation is completed (Windows may
prompt you more than once). When the installation is complete, click Finish.
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
45
Appendix D. Stand-Alone Flash
Programming Using the Keil µVision IDE
Observe the following procedure to program Flash memory without debugging.
1. From the Project menu, open the Options for Target 'your project’, and click the
Utilities tab. In the Use Target Driver for Flash Programming drop-down menu
within the Configure Flash Menu Command pane, ensure that Zilog Z8051 Target
Driver is selected, as indicated in Figure 39.
Figure 39. Selecting A Target Driver For Flash Programming
2. Click the Settings button to change any additional Flash options. The Settings dialog
will appear, as shown in Figure 40.
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
46
Figure 40. Configuring Additional Flash Options
3. After you have selected your Flash options, click OK to exit the Flash Options dialog.
4. Click OK to exit the Options For Target ‘Demo’ dialog.
5. From the Flash menu of the Keil IDE (see Figure 41), select either of the following
options:
– Select Download to program Flash memory with the current project
– Select Erase to perform a mass erase of internal Flash memory
Figure 41. The Keil IDE Flash Menu
UM025704-0413
Sample Projects and Documentation
Z51F0410 Evaluation Kit
User Manual
47
Customer Support
To share comments, get your technical questions answered, or report issues you may be
experiencing with our products, please visit Zilog’s Technical Support page at http://support.zilog.com.
To learn more about this product, find additional documentation, or to discover other facets about Zilog product offerings, please visit the Zilog Knowledge Base or consider participating in the Zilog Forum.
This publication is subject to replacement by a later edition. To determine whether a later
edition exists, please visit the Zilog website at http://www.zilog.com.
UM025704-0413
Customer Support
工商网监
湘ICP备2023018690号
