MBR30100CT

MBR3020CT THRU MBR30100CT Reverse Voltage - 20 to 100 Volts Forward Current - 30.0 Ampere SCHOTTKY BARRIER RECTIFIER Features TO-220AB  The plastic package carries Underwriters Laboratory Flammability Classification 94V-0  Construction utilizes void-free molded plastic technique  Low reverse leakage  High forward surge current capability  High temperature soldering guaranteed: 250°C,0.25”(6.35mm) from case for 10 seconds 0.185(4.70) 0.175(4.44) 0.154(3.91) DIA 0.148(3.74) 0.415(10.54) MAX 0.057(1.45) 0.051(1.30) 0.113(2.87) 0.103(2.62) 0.145(3.68) 0.135(3.43) 0.410(10.41) 0.390(9.91) PIN 1 0.560(14.2) 0.530(13.4) 0.350(8.89) 0.330(8.38) 0.635(16.13) 0.625(15.87) 1.148(29.16) 1.118(28.40) 0.160 (4.05) 0.140 (3.55) 0.110(2.79) 0.100(2.54) 0.590(14.22) 0.530(13.46) Mechanical Data 0.037(0.94) 0.027(0.68) 0.105 (2.67) 0.095 (2.41) 0.105 (2.67) 0.095 (2.41) Case : JEDEC TO-220AB Molded plastic body Terminals : Solder plated, solderable per MIL-STD-750,Method 2026 Polarity : Polarity symbol marking on body Mounting Position : Any Weight : 0.080 ounce, 2.24 grams 0.205 (5.20) 0.195 (4.95) 0.022(0.58) 0.014(0.35) PIN 1 PIN 2 PIN 3 CASE Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics Ratings at 25°C ambient temperature unlss otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. Parameter MBR Maximum RMS voltage Maximum DC blocking voltage Maximum average forward rectified current (see fig.1) Peak forward surge current 8.3ms single half sine-wave MBR MBR MDD MBR MDD MBR UNITS 3020CT 3030CT 3040CT 3045CT 3050CT 3060CT 3070CT 3080CT 3090CT 30100CT V RMM V RMS V DC 20 14 20 30 21 30 40 28 40 45 32 45 50 35 50 60 42 60 70 49 70 80 56 80 90 63 90 100 70 100 V V V I(AV) 30.0 A IFSM 250 A Maximum instantaneous forward voltage at 15.0A Maximum DC reverse current TA=25℃ at rated DC blocking voltage TA=100℃ VF 0.55 IR Typical junction capacitance (NOTE 1) Typical thermal resistance (NOTE 2) CJ 15.0 750 R θJC Operating junction temperature range TJ storage temperature range MBR MDD MDD MDD MDD MDD MDD MDD MDD MBR MBR MBR MBR MBR MBR MBR MBR Marking Code Maximum repetitive peak reverse voltage MBR MBR MBR MBR MBR MBR SYMBOLS 3020CT 3030CT 3040CT 3045CT 3050CT 3060CT 3070CT 3080CT 3090CT 30100CT T STG 0.75 1.0 0.85 50.0 500 2.0 -65 to +125 V mA pF ℃/W -65 to +150 -65 to +150 ℃ ℃ Note:1.Measured at 1MHz and applied reverse voltage of 4.0V D.C. 2.Thermal resistance from junction to case. DN:T19826A0 https://www.microdiode.com Rev:2019A0 Page :1 MBR3020CT THRU MBR30100CT Reverse Voltage - 20 to 100 Volts Forward Current - 30.0 Ampere FIG. 1- FORWARD CURRENT DERATING CURVE 30 24 18 Single Phase Half Wave 60Hz Resistive or inductive Load 12 6 MBR3020CT-MBR3045CT MBR3050CT-MBR30100CT 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES Ratings And Characteristic Curves FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 300 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 250 200 150 100 175 50 1 10 AMBIENT TEMPERATURE, C INSTANTANEOUS FORWARD CURRENT,AMPERES 250 50 TJ=25 C PULSE WIDTH=300 µs 1%DUTY CYCLE 0.5 MBR3020CT-MBR3045CT MBR3050CT-MBR3060CT MBR3070CT-MBR30100CT 0.05 0.2 0.4 0.6 0.8 1.0 FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MILLIAMPERES FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 5 1.1 100 10 TJ=100 C 1 TJ=75 C 0.1 0.01 20 40 60 80 100 2000 TJ=25 C 100 MBR3020CT-MBR3045CT MBR3050CT-MBR30100CT TRANSIENT THERMAL IMPEDANCE, C/W PERCENT OF PEAK REVERSE VOLTAGE,% FIG. 5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF TJ=25 C 0.001 0 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 1000 100 NUMBER OF CYCLES AT 60 Hz FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10 1 0.1 0.01 0.1 1 10 100 10 0.1 1.0 10 REVERSE VOLTAGE,VOLTS 100 t,PULSE DURATION,sec. The curve above is for reference only. https://www.microdiode.com Rev:2019A0 Page :2