IL260/IL261/IL262
High Speed Five-Channel Digital Isolators
Features
IN1
OUT1
IN2
OUT2
IN3
OUT3
IN4
OUT4
IN5
OUT5
IL260
IN1
OUT1
IN2
OUT2
IN3
OUT3
IN4
OUT4
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
High Speed: 110 Mbps
1.2 mA/channel typical quiescent current
Very high isolation: 6 kVRMS Reinforced Isolation (VE-Series)
50 kV/μs typ.; 30 kV/μs min. common mode transient immunity
No carrier or clock for low EMI emissions and susceptibility
−40 to 85 °C operating temperature
44000 year barrier life
Excellent magnetic immunity
2 ns typical pulse width distortion
100 ps pulse jitter
4 ns typical propagation delay skew
10 ns typical propagation delay
2 ns channel-to-channel skew
IEC 60747-17 (VDE 0884-17):2021-10 certified; UL 1577 recognized
0.15" and True 8™ mm 16-pin SOIC; 16-pin QSOP packages
IL
14 26004 1
00
Functional Diagrams
Applications
•
•
•
•
•
•
ADCs and DACs
Multiplexed data transmission
Board-to-board communication
Peripheral interfaces
Equipment covered under IEC 61010-1 Edition 3
5 kVRMS rated IEC 60601-1 medical applications
Description
OUT5
IN5
IL261
NVE’s IL260-Series five-channel high-speed digital isolators are
CMOS devices manufactured with NVE’s patented* spintronic
Giant Magnetoresistive (GMR) technology.
A unique ceramic/polymer composite barrier provides excellent
isolation and virtually unlimited barrier life.
IN1
OUT1
IN2
OUT2
IN3
OUT3
OUT4
IN4
OUT5
IN5
All transmit and receive channels operate at 110 Mbps over the full
temperature and supply voltage range. The symmetric magnetic
coupling barrier provides a typical propagation delay of only 10 ns
and a pulse width distortion of 2 ns, achieving the best specifications
of any isolator. The unique fifth channel can be is used to distribute
isolated clocks or handshake signals to multiple delta-sigma A/D
converters. High channel density makes these devices ideal for
isolating ADCs and DACs, parallel buses and peripheral interfaces.
Typical transient immunity of 50 kV/µs is unsurpassed.
Performance is specified over the temperature range of −40 °C to
+85 °C without derating.
The five-channel devices provide the highest channel density
available. Parts are available in ultraminiature 16-pin QSOPs,
as well as 0.15"and 0.3"-wide SOIC packages.
IL262
V-Series versions offer extremely high isolation voltage of 6 kVRMS,
and true 8 mm creepage.
IsoLoop is a registered trademark of NVE Corporation.
*U.S. Patent number 5,831,426; 6,300,617 and others.
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
REV. X
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
Absolute Maximum Ratings(1)
Parameters
Storage Temperature
Junction Temperature
Supply Voltage
Input Voltage
Output Voltage
Output Current Drive
Lead Solder Temperature
ESD
Symbol
TS
TJ
VDD1,VDD2
VI
VO
IO
Min.
−55
−55
−0.5
−0.5
−0.5
−10
Typ.
Max.
150
150
7
VDD + 0.5
VDD + 0.5
10
260
Units
°C
°C
V
V
V
mA
°C
kV
Test Conditions
Max.
85
100
5.5
VDD
0.8
1
Units
°C
°C
V
V
V
μs
Test Conditions
2
10 sec.
HBM
Recommended Operating Conditions
Parameters
Ambient Operating Temperature
Junction Temperature
Supply Voltage
Logic High Input Voltage
Logic Low Input Voltage
Input Signal Rise and Fall Times
Symbol
TA
TJ
VDD1,VDD2
VIH
VIL
tIR, tIF
Min.
−40
−40
2.5
2.4
0
Typ.
2
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
isoapps@nve.com
IL260/IL261/IL262
Safety and Approvals
IEC 60747-17 (VDE 0884-17):2021-10:
“VE” version (Reinforced Isolation; VDE File Number 5016933-4880-0002)
• Working Voltage (VIORM): 1200 VRMS (1700 VPK) with 20% Safety Factor; pollution degree 2
• Isolation voltage (VISO): 6000 VRMS
• Surge immunity (VIOSM): 12.8 kVPK
• Surge rating: 8000 V
• Transient overvoltage (VIOTM): 6000 VPK
• Each part tested at 2387 VPK for 1 second, 5 pC partial discharge limit
• Samples tested at 6000 VPK for 60 sec.; then 2122 VPK for 10 sec. with 5 pC partial discharge limit
Standard versions (Basic Isolation; VDE File Number 5016933-4880-0001)
• Isolation voltage (VISO): 2500 VRMS
• Transient overvoltage (VIOTM): 4000 VPK
• Surge rating: 4000 V
• Each part tested at 1590 VPK for 1 second, 5 pC partial discharge limit.
• Samples tested at 4000 VPK for 60 sec.; then 1358 VPK for 10 sec. with 5 pC partial discharge limit.
• Working Voltage (VIORM; pollution degree 2):
Package
QSOP16
Narrow-body SOIC16
Wide-body SOIC16/True 8™
Part No.
Suffix
-1
-3
None
Safety-Limiting Values
Safety rating ambient temperature
Safety rating power (180 °C)
Supply current safety rating (total of supplies)
Working
Voltage
600 VRMS
700 VRMS
600 VRMS
Symbol
TS
PS
IS
Value
180
270
54
Units
°C
mW
mA
UL 1577 (Component Recognition Program File Number E207481)
V-Series isolation grade
6 kV rating; tested at 7.2 kVRMS (10.2 kVPK) for 1 second; each lot sample tested at 6 kVRMS (8485 VPK) for 1 minute
Standard isolation grade
Each part tested at 3000 VRMS (4243 VPK) for 1 second; each lot sample tested at 2500 VRMS (3536 VPK) for 1 minute
Soldering Profile
Per JEDEC J-STD-020C, MSL 1
3
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
isoapps@nve.com
IL260/IL261/IL262
IL260 Pin Connections
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
IN1
GND1
IN2
IN3
IN4
VDD1
IN5
GND1
GND2
OUT5
OUT4
OUT3
OUT2
OUT1
GND2
VDD2
Input 1
Ground*
Input 2
Input 3
Input 4
Supply Voltage 1
Input 5
Ground*
Ground*
Output 5
Output 4
Output 3
Output 2
Output 1
Ground*
Supply Voltage 2
IN1
VDD2
GND1
GND2
IN2
OUT1
IN3
OUT2
IN4
OUT3
VDD1
OUT4
IN5
OUT5
GND1
GND2
IL260
IL261 Pin Connections
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VDD1
GND1
IN1
IN2
IN3
IN4
OUT5
GND1
GND2
IN5
OUT4
OUT3
OUT2
OUT1
GND2
VDD2
Supply Voltage 1
Ground*
Input 1
Input 2
Input 3
Input 4
Output 5
Ground*
Ground*
Input 5
Output 4
Output 3
Output 2
Output 1
Ground*
Supply Voltage 2
VDD1
VDD2
GND1
GND2
IN1
OUT1
IN2
OUT2
IN3
OUT3
IN4
OUT4
OUT5
IN5
GND1
GND2
IL261
IL262 Pin Connections
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
VDD1
GND1
IN1
IN2
IN3
OUT4
OUT5
GND1
GND2
IN5
IN4
OUT3
OUT2
OUT1
GND2
VDD2
Supply Voltage 1
Ground*
Input 1
Input 2
Input 3
Output 4
Output 5
Ground*
Ground*
Input 5
Input 4
Output 3
Output 2
Output 1
Ground*
Supply Voltage 2
VDD1
VDD2
GND1
GND2
IN1
OUT1
IN2
OUT2
IN3
OUT3
OUT4
IN4
OUT5
IN5
GND1
GND2
IL262
*NOTE: Pins 2 and 8 are internally connected, as are pins 9 and 15.
4
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
isoapps@nve.com
IL260/IL261/IL262
Parameters
Input Quiescent Current
Output Quiescent Current
IL260
IL261
IL262
IL260
IL261
IL262
Logic Input Current
Logic High Output Voltage
Logic Low Output Voltage
Maximum Data Rate
Minimum Pulse Width(7)
Propagation Delay Input to Output
(High to Low)
Propagation Delay Input to Output
(Low to High)
Pulse Width Distortion |tPHL−tPLH|(2)
Propagation Delay Skew(3)
Output Rise Time (10%–90%)
Output Fall Time (10%–90%)
Common Mode Transient Immunity
(Output Logic High to Logic Low)(4)
Channel-to-Channel Skew
Dynamic Power Consumption(6)
Power Frequency Magnetic Immunity
Pulse Magnetic Field Immunity
Damped Oscillatory Magnetic Field
Cross-axis Immunity Multiplier(9)
3.3 Volt Electrical Specifications (Tmin to Tmax)
Symbol
Min.
Typ.
Max.
300
400
IDD1
1.2
1.75
2.4
3.5
6
8.75
IDD2
4.8
7
3.6
5.25
Ii
−10
10
VDD−0.1
VDD
VOH
0.8 x VDD
0.9 x VDD
0
0.1
VOL
0.5
0.8
Switching Specifications (2.5 V 1014
5
VIO
VIOSM
44000
Symbol
Junction–Ambient
Thermal Resistance
Junction–Case (Top)
Thermal Resistance
QSOP
0.15" SOIC16
0.3" SOIC16
QSOP
0.15" SOIC16
0.3" SOIC16
Junction–Ambient
Thermal Resistance
Junction–Case (Top)
Thermal Resistance
0.3" SOIC
Power Dissipation
QSOP
0.15" SOIC16
0.3" SOIC16
θJA
θJC
Test Conditions
mm
Barrier Life
Parameter
Units
Thermal Characteristics
Min.
Typ.
100
82
67
9
8
12
θJA
46
θJC
9
Years
Max.
Per IEC 61000-4-5
100°C, 1000 VRMS, 60%
CL activation energy
Test Conditions
Double-sided PCB in
free air
°C/W
2s2p PCB in free air
per JESD51
675
675
1500
PD
Units
At maximum
operating temperature
mW
Notes:
1.
Absolute maximum means the device will not be damaged if operated under these conditions. It does not guarantee performance.
2.
PWD is defined as |tPHL − tPLH|. %PWD is equal to PWD divided by pulse width.
3.
tPSK is the magnitude of the worst-case difference in tPHL and/or tPLH between devices at 25°C.
4.
CMH is the maximum common mode voltage slew rate that can be sustained while maintaining VO > 0.8 VDD2. CML is the maximum
common mode input voltage that can be sustained while maintaining VO < 0.8 V. The common mode voltage slew rates apply to both rising
and falling common mode voltage edges.
5.
Device is considered a two terminal device: pins 1–8 shorted and pins 9–16 shorted.
6.
Dynamic power consumption numbers are calculated per channel and are supplied by the channel’s input side power supply.
7.
Minimum pulse width is the minimum value at which specified PWD is guaranteed.
8.
The relevant test and measurement methods are given in the Electromagnetic Compatibility section on p. 8.
9.
External magnetic field immunity is improved by this factor if the field direction is “end-to-end” rather than to “pin-to-pin” (see diagram on p. 8).
10. 66,535-bit pseudo-random binary signal (PRBS) NRZ bit pattern with no more than five consecutive 1s or 0s; 800 ps transition time.
7
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
isoapps@nve.com
IL260/IL261/IL262
Application Information
Electrostatic Discharge Sensitivity
IL260/IL261/IL262 parts have a maximum junction temperature of
110°C. Based on the specifications contained in this datasheet, the
derating curve at typical operating conditions is as follows:
This product has been tested for electrostatic sensitivity to the
limits stated in the specifications. However, NVE recommends that
all integrated circuits be handled with appropriate care to avoid
damage. Damage caused by inappropriate handling or storage could
range from performance degradation to complete failure.
Electromagnetic Compatibility
IsoLoop Isolators have the lowest EMC footprint of any isolation
technology. There are no internal clocks or carriers. IsoLoop
Isolators’ Wheatstone bridge configuration and differential
magnetic field signaling ensure excellent EMC performance against
all relevant standards.
These isolators are fully compliant with IEC 61000-6-1 and
IEC 61000-6-2 standards for immunity, and IEC 61000-6-3,
IEC 61000-6-4, CISPR, and FCC Class A standards for emissions.
Immunity to external magnetic fields is even higher if the field
direction is “end-to-end” rather than to “pin-to-pin” as shown in the
diagram below:
Power Supply Decoupling
Both power supplies should be bypassed with 0.1 µF typical
(0.047 µF minimum) capacitors as close as possible to the VDD
pins. Ground planes for both GND1 and GND2 are highly
recommended for data rates above 10 Mbps.
Maintaining Creepage
Creepage distances are often critical in isolated circuits. In addition
to meeting JEDEC standards, NVE isolator packages have unique
creepage specifications. Standard pad libraries often extend under
the package, compromising creepage and clearance. Similarly,
ground planes, if used, should be spaced to avoid compromising
clearance. Package drawings and recommended pad layouts are
included in this datasheet.
Cross-axis Field Direction
Dynamic Power Consumption
IsoLoop Isolators achieve their low power consumption from the
way they transmit data across the isolation barrier. By detecting the
edge transitions of the input logic signal and converting these to
narrow current pulses, a magnetic field is created around the GMR
Wheatstone bridge. Depending on the direction of the magnetic
field, the bridge causes the output comparator to switch following
the input logic signal. Since the current pulses are narrow, about
2.5 ns, the power consumption is independent of mark-to-space
ratio and solely dependent on frequency. This has obvious
advantages over optocouplers, which have power consumption
heavily dependent on mark-to-space ratio.
Signal Status on Start-up and Shut Down
To minimize power dissipation, input signals are differentiated and
then latched on the output side of the isolation barrier to reconstruct
the signal. This could result in an ambiguous output state
depending on power up, shutdown and power loss sequencing.
Therefore, the designer should consider including an initialization
signal in the start-up circuit. Initialization consists of toggling the
input either high then low, or low then high.
Thermal Management
IsoLoop Isolators are designed for low power dissipation and
thermal performance, providing unmatched channel density for
high-performance isolators. Nevertheless, package temperature rise
should be considered when running multiple channels at high
speed. Power consumption is higher at 5 volt operation than at
3.3 volts, and dynamic supply current is higher on the input side of
the isolators than the output side, so thermal management is more
important with five-volt input-side power supplies.
8
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
isoapps@nve.com
IL260/IL261/IL262
Application Diagram—Multi-Channel Delta-Sigma A/D Converter
In a typical single-channel delta-sigma ADC, the system clock is located on the isolated side of the system and only four channels of isolation are
required. With multiple ADCs configured in a channel-to-channel isolation configuration, however, clock jitter and edge placement accuracy of
the system clock must be matched between ADCs. The best solution is to use a single clock on the system side and distribute the clock to each
ADC. The five-channel IL261 is ideal, with the fifth channel used to distribute a single, isolated clock to multiple ADCs as shown below:
Bridge
Bias
Delta Sigma A/D
CS5532
Bridge +
Bridge Isolation
Boundary
Serial Data Out
Iso SD Out
Serial Data In
Iso SD In
Data Clock
Iso Data Clock
Chip Select
Iso CS
Clock
Generator
Channel 1
IL261
OSC 2
Bridge
Bias
Delta Sigma A/D
CS5532
Bridge +
Bridge -
Channel n
Serial Data Out
Iso SD Out
Serial Data In
Iso SD In
Data Clock
Iso Data Clock
Chip Select
Iso CS
IL261
OSC 2
9
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
isoapps@nve.com
IL260/IL261/IL262
Package Drawings
Ultraminiature 16-pin QSOP Package (-1 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.188 (4.77)
0.197 (5.00)
0.020 (0.50)
0.029 (0.75)
0.050 (1.27)
0.056 (1.42)
0.060 (1.52)
0.069 (1.75)
0.150 (3.8)
0.157 (4.0)
0.228 (5.8)
0.244 (6.2)
0.004 (0.10)
0.010 (0.25)
0.025 (0.635)
NOM
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0.007 (0.20)
0.010 (0.25)
0.009 (0.2)
0.012 (0.3)
0.15" 16-pin SOIC Package (-3 suffix)
Dimensions in inches (mm); scale = approx. 5X
0.013 (0.3)
0.020 (0.5)
NOM
0.007 (0.2)
0.013 (0.3)
0.386 (9.8)
0.394 (10.0)
Pin 1 identified
by either an
indent or a
marked dot
0.016 (0.4)
0.050 (1.3)
0.055 (1.40)
0.062 (1.58)
0.054 (1.4)
0.072 (1.8)
0.150 (3.81)
0.157 (3.99)
0.049 (1.24)
0.051 (1.30)
0.228 (5.8)
0.244 (6.2)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
0.004 (0.1)
0.012 (0.3)
10
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
0.3" 16-pin SOIC Package (no suffix)
Dimensions in inches (mm); scale = approx. 5X
0.033 (0.85)*
0.043 (1.10)
0.260 (6.60)*
0.280 (7.11)
0.013 (0.3)
0.020 (0.5)
0.007 (0.2)
0.013 (0.3)
0.397 (10.08)
0.413 (10.49)
0.017 (0.43)*
0.022 (0.56)
0.016 (0.4)
0.050 (1.3)
0.007 (0.18)*
0.010 (0.25)
0.092 (2.34)
0.105 (2.67)
Pin 1 identified by
either an indent
or a marked dot
0.08 (2.0)
0.10 (2.5)
0.292 (7.42)*
0.299 (7.59)
0.049 (1.24)
0.051 (1.30)
0.394 (10.00)
0.419 (10.64)
NOTE: Pin spacing is a BASIC
dimension; tolerances
do not accumulate
*Specified for True 8™ package to guarantee 8 mm creepage per IEC 60601.
0.004 (0.1)
0.012 (0.3)
11
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
Recommended Pad Layouts
4 mm x 5 mm 16-pin QSOP Pad Layout
Dimensions in inches (mm); scale = approx. 5X
0.160 (4.05)
0.025 (0.635)
0.012 (0.30)
16 PLCS
0.275 (6.99)
0.15" 16-pin SOIC Pad Layout
Dimensions in inches (mm); scale = approx. 5X
0.160 (4.06)
0.050 (1.27)
0.020 (0.51)
16 PLCS
0.275 (6.99)
12
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
0.3" 16-pin SOIC Pad Layout
Dimensions in inches (mm); scale = approx. 5X
0.317 (8.05)
0.050 (1.27)
0.020 (0.51)
16 PLCS
0.449 (11.40)
13
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
Available Parts
Available
Parts
IL260-1E
IL260-3E
IL260E
IL260VE
IL261-1E
IL261-3E
IL261E
IL261VE
IL262-3E
IL262E
IL262VE
Transmit
Channels
5
5
5
5
4
4
4
4
3
3
3
Receive
Channels
0
0
0
0
1
1
1
1
2
2
2
Isolation
Voltage
(RMS)
2.5 kV
2.5 kV
2.5 kV
6 kV
2.5 kV
2.5 kV
2.5 kV
6 kV
2.5 kV
2.5 kV
6 kV
Package
QSOP
Narrow SOIC
Wide SOIC
Wide SOIC
QSOP
Narrow SOIC
Wide SOIC
Wide SOIC
Narrow SOIC
Wide SOIC
Wide SOIC
All part types are available on tape and reel.
Ordering Information
IL 260 V - 3 E TR13
Valid Part Numbers
Bulk Package
Blank = Tube
TR7 = 7'' Tape and Reel
TR13 = 13'' Tape and Reel
Package
Blank = 80/20 Tin/Lead Plating
E = RoHS Compliant
Package Type
Blank = 0.3" 16-pin SOIC
-1 = 0.15'' 16-pin QSOP
-3 = 0.15'' 16-pin SOIC
Grade
Blank = Standard Isolation
Voltage (2.5 kV)
V = High Isolation
Voltage (6 kV)
IL260
IL260E
IL260VE
IL260-1E
IL260-3
IL260-3E
IL261
IL261E
IL261VE
IL261-1E
IL261-3
IL261-3E
IL262
IL262E
IL262VE
IL262-3
IL262-3E
All IL260-Series part
types are available on
tape and reel.
Base Part Number
260 = 5 Transmit Channels
261 = 4 Transmit Channels;
1 Receive Channel
262 = 3 Transmit Channels;
2 Receive Channel
Product Family
IL = Isolators
RoHS
COMPLIANT
14
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
Revision History
ISB-DS-001-IL260/1/2-X
August 2022
Change
• Upgraded to IEC 60747-17 (VDE 0884-17):2021-10 (p. 3).
•
ISB-DS-001-IL260/1/2-W
Increased Working Voltage ratings based on latest VDE testing (p. 3).
Changes
Reduced minimum supply voltage to 2.5 V (p. 2).
•
ISB-DS-001-IL260/1/2-V
•
Updated EMC standards.
•
Deleted minimum magnetic field immunity specifications (not 100% tested).
•
Updated thermal specifications (p. 7).
Change
VDE certification and UL approval for V-Series versions
(6 kV reinforced isolation).
•
ISB-DS-001-IL260/1/2-U
ISB-DS-001-IL260/1/2-T
ISB-DS-001-IL260/1/2-S
ISB-DS-001-IL260/1/2-R
ISB-DS-001-IL260/1/2-Q
Changes
• Updated VDE certification standard to VDE V 0884-10.
•
Upgraded “VE” Version Surge Immunity specification to 12.8 kV.
•
Upgraded “VE” Version VDE 0884-10 rating to reinforced insulation.
•
Corrected QSOP pin width dimension (p. 10).
Changes
• Increased V-Series isolation voltage to 6 kVrms.
•
Increased typ. Total Barrier Thickness specification to 0.016 mm.
•
Increased CTI min. specification to ≥600 VRMS.
Changes
•
Added V-Series 5 kV isolation voltage versions.
•
More detailed “Available Parts” table.
Changes
•
Added QSOP packages (-1 suffix).
•
Revised and added details to thermal characteristic specifications (p. 2).
•
Added VDE 0884 Safety-Limiting Values (p. 3).
•
Added “Thermal Management” paragraph in Applications section.
Change
•
ISB-DS-001-IL260/1/2-P
IEC 60747-5-5 (VDE 0884) certification.
Changes
•
Tighter quiescent current specifications.
•
Upgraded from MSL 2 to MSL 1.
15
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
Datasheet Limitations
The information and data provided in datasheets shall define the specification of the product as agreed between NVE and its customer, unless NVE and
customer have explicitly agreed otherwise in writing. All specifications are based on NVE test protocols. In no event however, shall an agreement be
valid in which the NVE product is deemed to offer functions and qualities beyond those described in the datasheet.
Limited Warranty and Liability
Information in this document is believed to be accurate and reliable. However, NVE does not give any representations or warranties, expressed or
implied, as to the accuracy or completeness of such information and shall have no liability for the consequences of use of such information.
In no event shall NVE be liable for any indirect, incidental, punitive, special or consequential damages (including, without limitation, lost profits, lost
savings, business interruption, costs related to the removal or replacement of any products or rework charges) whether or not such damages are based on
tort (including negligence), warranty, breach of contract or any other legal theory.
Right to Make Changes
NVE reserves the right to make changes to information published in this document including, without limitation, specifications and product descriptions
at any time and without notice. This document supersedes and replaces all information supplied prior to its publication.
Use in Life-Critical or Safety-Critical Applications
Unless NVE and a customer explicitly agree otherwise in writing, NVE products are not designed, authorized or warranted to be suitable for use in life
support, life-critical or safety-critical devices or equipment. NVE accepts no liability for inclusion or use of NVE products in such applications and such
inclusion or use is at the customer’s own risk. Should the customer use NVE products for such application whether authorized by NVE or not, the
customer shall indemnify and hold NVE harmless against all claims and damages.
Applications
Applications described in this datasheet are illustrative only. NVE makes no representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Customers are responsible for the design and operation of their applications and products using NVE products, and NVE accepts no liability for any
assistance with applications or customer product design. It is customer’s sole responsibility to determine whether the NVE product is suitable and fit for
the customer’s applications and products planned, as well as for the planned application and use of customer’s third party customers. Customers should
provide appropriate design and operating safeguards to minimize the risks associated with their applications and products.
NVE does not accept any liability related to any default, damage, costs or problem which is based on any weakness or default in the customer’s
applications or products, or the application or use by customer’s third party customers. The customer is responsible for all necessary testing for the
customer’s applications and products using NVE products in order to avoid a default of the applications and the products or of the application or use by
customer’s third party customers. NVE accepts no liability in this respect.
Limiting Values
Stress above one or more limiting values (as defined in the Absolute Maximum Ratings System of IEC 60134) will cause permanent damage to the
device. Limiting values are stress ratings only and operation of the device at these or any other conditions above those given in the recommended
operating conditions of the datasheet is not warranted. Constant or repeated exposure to limiting values will permanently and irreversibly affect the
quality and reliability of the device.
Terms and Conditions of Sale
In case an individual agreement is concluded only the terms and conditions of the respective agreement shall apply. NVE hereby expressly objects to
applying the customer’s general terms and conditions with regard to the purchase of NVE products by customer.
No Offer to Sell or License
Nothing in this document may be interpreted or construed as an offer to sell products that is open for acceptance or the grant, conveyance or implication
of any license under any copyrights, patents or other industrial or intellectual property rights.
Export Control
This document as well as the items described herein may be subject to export control regulations. Export might require a prior authorization from national
authorities.
Automotive Qualified Products
Unless the datasheet expressly states that a specific NVE product is automotive qualified, the product is not suitable for automotive use. It is neither
qualified nor tested in accordance with automotive testing or application requirements. NVE accepts no liability for inclusion or use of non-automotive
qualified products in automotive equipment or applications.
In the event that customer uses the product for design-in and use in automotive applications to automotive specifications and standards, customer (a) shall
use the product without NVE’s warranty of the product for such automotive applications, use and specifications, and (b) whenever customer uses the
product for automotive applications beyond NVE’s specifications such use shall be solely at customer’s own risk, and (c) customer fully indemnifies
NVE for any liability, damages or failed product claims resulting from customer design and use of the product for automotive applications beyond NVE’s
standard warranty and NVE’s product specifications.
16
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
IL260/IL261/IL262
An ISO 9001 Certified Company
NVE Corporation
11409 Valley View Road
Eden Prairie, MN 55344-3617 USA
Telephone: (952) 829-9217
www.nve.com
e-mail: iso-info@nve.com
©NVE Corporation
All rights are reserved. Reproduction in whole or in part is prohibited without the prior written consent of the copyright owner.
ISB-DS-001-IL260/1/2-X
August 2022
17
NVE Corporation
11409 Valley View Road, Eden Prairie, MN 55344-3617
(952) 829-9217
www.nve.com
YouTube.com/NveCorporation
iso-apps@nve.com
工商网监
湘ICP备2023018690号
