承 認 書
SPECIFICATION
客 戶:
(Customer)
品 名:
(Product Name)
华秋
铝电解电容器
规 格：
RTV 系列
(Specifications）
日
期：
（Date）
2023 年 9 月 20 日
供應商簽署欄 Supplier confirmation
PREPARED BY
CHECKED BY
APPROVED BY
客戶確認簽署欄 Customer confirmation
珠海華冠電容器股份有限公司
ZHUHAI LEAGUER CAPACITOR CO.,LTD.
地址: 廣東省珠海市金鼎華冠科技工業園
Add:Higrand Scientific Industrial Park ,Jinding town ,Zhuhai,Guangdong
TEL:(0756)3610222
(FAX):(0756)3610938
HTTP: //www.headcon.cn.
序号
No.
更改原因
Explanation of changes
更改内容
Content
修订人
Reviser
生效日期
Effective date
1
新版
新版
王学莲
2023/9/20
华冠电容规格承认书目录
Leaguer product specification content
1、Standard Rating 基本参数………………………………………………………………… P.2
2、Scope 概述………………………………………………………………………………………… P.3
3、Applicable Specifications 参考标准………………………………………………… P.3
4、Operating Temperature Range 工作温度范围…………………………………………
P.3
5、Condition of Test 测试环境…………………………………………………………………P.3
6、Electrical Requirements 电性能要求……………………………………………… P.4~7
7、Marking 标示…………………………………………………………………………………… P.8
8、Part No System 物料编码………………………………………………………………… P.9
9、Lead Forming Type 加工型式……………………………………………………………P.10~11
10、Packing quantity 包装数量…………………………………………………………………P.12
11、Other Remarks 其它说明………………………………………………………………… P.13~14
Name
RTV
Version
01
Page
1
1、 Standard Rating 基本参数
￠d±0.05
F±0.5
L±a
No.
Customer
Part No.
Tolerance
Rated Surge
Operating
Capacitance
on Rated
Voltage Voltage Temp. Range
(µF)
Capacitance
(Vdc)
(Vdc)
(℃)
(%)
LEAGUER
Part No.
D+0.5 MAX
4MIN
15 MIN
tanδ
Leakage
(120Hz)
Current
(Max) (µA)(2min.)
Dimensions (mm)
Max Ripple
Current (mA)
at105℃120Hz
Endurance
at 105℃
(Hours)
φD
L
α
d
F
1
RTV1A471M0611B1
470
±20
10
11.5
-55~+105
0.28
47
145
1000
6.3
11
1.5
0.5
2.5
2
RTV1C471M0812B1
470
±20
16
18.4
-55~+105
0.18
75.2
280
1000
8
12
1.5
0.5
3.5
3
RTV1E221M0812B1
220
±20
25
28.8
-55~+105
0.16
55
280
1000
8
12
1.5
0.5
3.5
Name
RTV
Version
01
Page
2
No.
Customer
Part No.
LEAGUER
Part No.
Tolerance
Rated Surge
Operating
tanδ
Leakage
Capacitance on Rated
Voltage Voltage Temp. Range (120Hz)
Current
(µF)
Capacitance
(Vdc)
(Vdc)
(℃)
(Max) (µA)(2min.)
(%)
Dimensions (mm)
Max Ripple
Current (mA)
at105℃120Hz
Endurance
at 105℃
(Hours)
φD
L
α
d
F
4
RTV1V101M0611B1
100
±20
35
40.3
-55~+105
0.14
35
86
1000
6.3
11
1.5
0.5
2.5
5
RTV1V471M1016B1
470
±20
35
40.3
-55~+105
0.14
164.5
525
2000
10
16
2.0
0.6
5.0
6
RTV1V102M1321B1
1000
±20
35
40.3
-55~+105
0.14
350
1080
2000
13
21
2.0
0.6
5.0
7
RTV1H100M0511B1
10
±20
50
57.5
-55~+105
0.12
5
42
1000
5
11
1.5
0.5
2.0
8
RTV1H470M0611B1
47
±20
50
57.5
-55~+105
0.12
23.5
88
1000
6.3
11
1.5
0.5
2.5
9
RTV1H101M0812B1
100
±20
50
57.5
-55~+105
0.12
50
194
1000
8
12
1.5
0.5
3.5
10
RTV2A470M1012B1
470
±20
100
115
-55~+105
0.10
470
490
2000
10
12
2.0
0.6
5.0
11
RTV1J470M0812B1
47
±20
63
72.4
-55~+105
0.12
29.6
162
1000
8
12
1.5
0.5
3.5
12
RTV1J471M1321B1
470
±20
63
72.4
-55~+105
0.12
296.1
645
2000
13
21
2.0
0.6
5.0
13
RTV1J102M1625B1
1000
±20
63
72.4
-55~+105
0.12
630
1296
2000
16
25
2.5
0.8
7.5
14
RTV2A100M0611B1
10
±20
100
115
-55~+105
0.10
10
98
1000
6.3
11
1.5
0.5
2.5
15
RTV2A101M1020B1
100
±20
100
115
-55~+105
0.10
100
320
2000
10
20
2.0
0.6
5.0
16
RTV1V222M1625B1
2200
±20
35
40.3
-55~+105
0.16
770
1500
2000
16
25
2.5
0.8
7.5
3
Name
RTV
Version
01
Page
2、 SCOPE 概述
本承认书规定了 RTV 系列径向引线引出铝电解电容器的技术规范，本技术规范条文解释权归
本公司所有。
This specification covers “RTV series” miniature single-ended aluminum electrolytic capacitors，
Leaguer reserves the right of final interpretation for this technical specification.
3、 APPLICABLE SPECIFICATION 参考标准
本承认书参考 JIS-C-5101-1 和 JIS-C-5101-4 制定。
This approval sheet consulted the institute of JIS-C-5101-1 and JIS-C-5101-4.
4、OPERATING TEMPERATURE RANGE 工作温度范围
工作温度范围是电容器在施加额定工作电压条件下，可以长期可靠工作的环境温度范围。
-55℃~+105℃（10V.DC~100V.DC）
Operating temperature range is the range of ambient temperature at which the capacitor can be
operated continuously at rated voltage.
-55℃~+105℃（10V.DC~100V.DC）
5、CONDITION OF TEST 测试环境
如果没有其他规定，标准的测试、检验环境条件如下所示：
环境温度：15℃~35℃
相对湿度：45%~75%
大气压力：86kpa~106kpa
如果对测试结果有异议，可以在以下条件测试：
环境温度：20±1℃
相对湿度：60%~67%
大气压力：86kpa~106kpa
Unless otherwise specified, the standard range of atmospheric conditions for making
measurements and tests are as follows
Ambient temperature ：15℃ to 35℃
Relative humidity ：45% to 75%
Air pressure
：86kpa to 106kpa
If there may be doubt on the results, measurements shall be made within the following limits
Ambient temperature ：20±1℃
Relative humidity
：60% to 67%
Air pressure
：86kpa to 106kpa
Name
RTV
Version
01
Page
4
6、 Electrical Requirements 电性能要求
序号
项目
测试方法
性能
No.
Item
Test method
Performance
6.1
额定工作电压
10V.DC~100V.DC
Rated voltage
容量范围：
测试频率：120Hz(±20%)
4.7μF ~4700μF
测试电路：串联等效
6.2
电容量
Capacitance
容量偏差：-20%~+20%
测试电压：0.5Vrms 以下
Range of Capacitance:
Measuring frequency: 120Hz±20%
4.7μF ~4700μF
Measuring circuit : Series equivalent circuit
Capacitance tolerance:
Measuring voltage :0.5Vrms or less
损失角正切值
6.3
Dissipation
factor
-20%~+20%
测试条件与 6.2 电容量测试相同
Testing conditions are the same as 6.2 for capacitance
W.V
10
16
25
35
50
63
80
100
Tg δ
0.20
0.16
0.14
0.12
0.10
0.10
0.08
0.08
在电容器两端施加额定工作电压，并串联 1000±100
6.3V~100V:
Ω电阻，在施加规定时间电压后，测量漏电流。
I≤0.01CV 或 3μA，
测试电路如下图：
取较大值（2 分钟后）
The rated voltage shall be applied across the capacitor
6.3V~100V:
and its protective resistor shall be 1000±100Ω. The
I≤0.01CV or 3μA
leakage current shall then be measured after an
Whichever is greater（after 2 min）
electrification period of schedule time.
I：漏电流（μA）
Measurement circuit
C：容量（μF）
V：额定工作电压（V）
漏电流
6.4
I：Leakage current(μA)
Leakage
C：Capacitance(μF)
current
V：Rated voltage (V)
Rs: Protective resistor(1000±100Ω)
DC ammeter
DC voltmeter
S1: Switch
S2: Protective switch for an ammeter
6.5
低温特性
Low
Temperature
Characteristics
(at 120Hz)
Name
WV
10
16
25
35
50
63
80
100
Z－25℃/ Z +20℃
3
2
2
2
2
2
2
2
Z－40℃/ Z +20℃
4
4
4
4
4
4
4
4
RTV
Version
01
Page
5
序号
项目
测试方法
性能
No.
Item
Test method
Performance
Step
Characteristics
at High and
6.6
Low
Temperature
高低温特性
6.7
耐浪涌电压
Test
Temperature
阶段 2
Time
阻抗比：相对于阶段 1 比值小于 6.5
中的值
1
20±2℃
-
2
-40±3℃
2 hours
Step2
3
20±2℃
15min
Impedance ratio: relative to Step2, the
4
105±2℃
2 hours
ratio is less than the value in 6.5
阶段 1：测量容量和阻抗（|z| 20℃ 120Hz±20%）
阶段 2：电容器恒温贮存 2 小时，在热平衡状态测阻
抗（|z| -40℃ 120Hz±20%）
阶段 4：电容器恒温贮存 2 小时，在热平衡状态测漏
电流
Step 1:Capacitance and impedance shall be
measured. （|z| 20℃ 120Hz±20%）
Step 2:After the capacitor being stored for 2 hours,
impedance shall be measured at thermal
stability. （|z| -40℃ 120Hz±20%）
Step 4:After the capacitor being stored for 105℃2
hours,leakage current shall be measured. The
measurement shall be made at thermal stability
对电容器施加浪涌电压，每充电 30s，放电
5min30sec，连续循环 1000 次后测量。
测试温度：15~35℃。
After surge voltage(the value of page 2) applied at a
cycling rate of 30 seconds charge and 5.5 minutes
discharge 1000 successive test cycle.
Test temperature:15~35℃.
阶段 4
漏电流：小于或等于规定值的 8 倍
Step4
Leakage Current : Less than 800% of
the specified value
漏电流：≤第 2 页规定值
Leakage Current : Less than the
specified value of page 2
容量变化：与初始测量值比变化率
±15%范围内
Capacitance Change : Within ±15% of
the initial measured value
损耗角正切值：规定值的 130%.
Tangent of Loss Angle : Less than
130% of specified value
Test circuit
Surge Test
Note: This requirement is applicable only to instantaneous over voltage which may be applied to
terminals of capacitor, therefore, not applicable to such over voltages as often applied.
6.8
可焊性
Solderability
Name
温度： 235±2℃
浸入时间：2±0.5sec
浸入深度：浸入引线约 0.5~1mm
助焊剂：约 25%的松香溶于酒精
Temperature : 235±2℃
Immersing Time: 2±0.5sec
Immersing Depth ： Dip the terminal for Approx.
0.5~1mm thick
Flux: Approx. 25% rosin in Ethanol
RTV
Version
01
引线端子表面 90%以上的面积附着
新焊料。
More than 90% of the terminal
surface shall be covered with new
solder.
Page
6
序号
项目
测试方法
性能
No.
Item
Test method
频率：10 到 55 Hz，每分钟互换
振幅：0.75mm
在互相垂直的 3 个方向上，每个方向振动 2 小时，
共 6 小时。
Frequency: 10~55Hz reciprocation for 1 min
Total amplitudes: 0.75mm
Direction and during of vibration: 3 orthogonal
directions, Mutually each for 2hrs total 6hrs
Performance
容量：在测试的 30 分钟内，电容量
测试值无明显变化
外观：无可见损伤
6.9
6.10
振动
Vibration
耐焊接热
Resistance to
soldering heat
端子强度
6.11
Terminal
strength
6.12
稳态湿热
Resistance to
damp heat
(steady state)
Name
容量变化：容量变化率在±10%范围内
焊槽法：Solder bath method：
焊锡温度：260±5℃
Solder bath temperature : 260±5℃
浸入时间：10±1 秒
Immersion time : 10±1sec.
电路板 ：1.6mm
Printed wiring board: 1.6mm
端子抗拉强度：
沿电容器端子引线方向施加拉力(如下表)，10±1 秒。
引线直径Φ 0.45
0.5
0.6
0.8
1.0
拉力 N
5
10
20
端子抗弯强度：
在电容器引线施加固定重力（如下表），然后，将
电容体弯折 90°后回到原位，再向相反方向弯折
90°后回到原位。
上述过程在 5 秒内完成。
引线直径Φ
0.45
0.5
0.6
0.8
1.0
拉力 N
2.5
5
10
Tensile strength of terminal:
A static load （stated in the table above） shall be
applied to the terminal in the axial direction and acting
in a direction away from the body for 10±1 sec..
Bending strength of terminal:
Hang the specified dead weight （stated in the table
above）, then bend the body through 90°, return to
the original position.
Next bend it in opposite direction through 90° with
the same speed, again return to the original position.
Complete this operation in about 5 sec.
电 容 器 放 置 在 温 度 60℃ 、 湿 度 90~95% 的 环 境 下
500±6 小时，然后放置在标准环境中恢复 1-2 小时
Capacitors shall be exposed for 500±6hrs in an
atmosphere of 90~95% R.H. at 60℃. And then the
capacitor shall be subjected to standard atmospheric
conditions for 1-2 hours, after which measurements
shall be made.
RTV
Version
01
Capacitance : Within 30 minutes of
the test, the capacitance test value
has no obvious change
Appearance: No significant change can
be observe
Capacitance change : Within ±10% of
initial measured value
外观：无可见损伤
容量变化：容量变化率在±10%范围
内
Appearance: No significant change can
be observe
Capacitance change : Within ±10% of
initial measured value
测量电容器应无接触不良、开路或短
路，无可见机械损伤
When the capacitor is measured, there
shall be no intermittent contacts, or
open or short-circuiting.
There shall be no visible mechanical
damage.
容量变化：与初始测量值比变化率在
±20%范围内。
损耗角正切值：≤规定值的 1.5 倍
漏电流：≤规定值
外观：无可见损伤
Capacitance Change: Within ±20% of
the initial measured value
Tangent of Loss Angle : Less than
150% of the specified value
Leakage Current : Less than the
specified value
Appearance : No significant change
can be observed.
Page
7
序号
项目
测试方法
性能
No.
Item
Test method
Performance
温度: 105±2℃
试验持续时间：1000~2000 小时 。
施加电压：额定电压
试验完成后，电容器在测量前应在室温中恢复 16 小
时。
Test Duration: 1000~2000hours。
Applied Voltage: Rated Voltage
After subjected to the test, the capacitors shall be left
at the room temperature for 16 hours prior to the
measurement.
容量变化:与初始测量值比变化率在
±30%范围内。
损耗角正切值 : ≤规定值的 3 倍
漏电流 : ≤规定值
外观:无可见损伤
Capacitance Change: Within ±30% of
the initial measured value
Tangent of Loss Angle : Less than
300% of the specified value
Leakage Current : Less than the
specified value
Appearance: No significant change can
be observed.
容量变化:与初始测量值比变化率在
±20%范围内。
损耗角正切值 : ≤规定值的 2 倍
漏电流 : ≤规定值的 2 倍
外观:无可见损伤
Capacitance Change: Within ±30% of
the initial measured value
Tangent of Loss Angle : Less than
300% of the specified value
Leakage Current : Less than the
specified value
Appearance: No significant change can
be observed.
高温负荷寿命
6.13
6.14
6.15
6.16
High
Temperature
Unload Life
Test
高温储存
High
Temperature
Unload Life
Test
防爆试验
Safety vent
自然放置下
的储存规定
Storage
requirements
in natural
state
温度: 105±2℃
试验持续时间：1000 小时
试验完成后，电容器在测量前应在室温中恢复 16 小
时。
Test Temperature: 105±2℃
Test Duration: 1000 hours
After subjected to the test, the capacitors shall be left
at the room temperature for 16 hours prior to the
measurement.
以下试验只适用于铝壳直径≥Φ8 产品。
The following tests only apply to those products with 上述过程中应无引线、铝箔等散射，
vent products at diameter≥Φ8 with vent.
无火花产生。
在电容器两极施加反向工作电压，其中通过的电流 The safety vent is actuated under the
为 1 A，在测试时防爆装置应能在 30 分钟内动作。 test conditions, thereby preventing
D．C．Application test
terminals, metal pieces, etc, of the
The capacitor shall be subjected to a reverse D.C. capacitor from scattering due to burst,
voltage equal to the rated D.C.voltage.
the case from separating from the seal
The current flowing through the capacitor shall be 1A. packing, or the capacitor from
If the vent does work with the voltage applied for 30 producing flame.
minutes, the test is considered to be passed.
1、 环境温度：-10~35℃，环境湿度：75%RH；
2、 产品储存期限为 12 个月；
3、 产品储存期限12 个月时，需送回工序重新老化；
4、 存放时间超过 3 年的电解电容器应立即报废，不可再使用；
1、 Ambient temperature：-10~35℃，Ambient humidity：75%RH；
2、 Storage time：12 months
3、 Storage time 12 months，need ageing again；
4、 Storage time three years, need to be discarded;
Name
RTV
Version
01
Page
8
7-1 额定纹波电流的频率系数 Frequency coefficient of rated ripple current
频率 (Hz)
60（50）
120
500
1K
10K≤
0.47~1μF
0.50
1.0
1.20
1.30
1.50
2.2～4.7μF
0.65
1.0
1.20
1.30
1.50
10～47μF
0.80
1.0
1.20
1.30
1.50
100～1000μF
0.80
1.0
1.10
1.15
1.20
2200~3300μF
0.80
1.0
1.05
1.10
1.15
7-2 Marking 标示
a) Following items shall be marked on the sleeving；
Sleeve color：Black；Marking color：Golden.
电容器的套管上印刷以下内容;套管颜色：黑色；标记颜色：金色。
ⅰ.
LEAGUER
商标
ⅱ.
Capacitance
额定容量
ⅲ.
Series
系列代码
ⅳ.
Rated Voltage
额定电压
ⅴ.
105℃
产品使用上限温度
ⅵ.
Negative Polarity
负极标示
ⅶ.
PET
套管材质标识
ⅷ.
Code
制造代码
Name
RTV
Version
01
Page
9
8、PART NO SYSTEM 物料编码
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
Packing code
Size code
Capacitance tolerance code
Capacitance code
Voltage code
Series code
1
2
4
3
Series code
Voltage
(V)
5
6
Code
7
Capacitance
(µF)
9
8
Code
Capacitance
tolerance
10 11 12 13
Code
Size
Code
14 15
Packing
Code
Bulk packing
B1
Lead Cut
C1
RTZ
2.5
0E
0.1
0R1
±5%
J
4×5
0405
RT1
4
0G
0.22
R22
±10%
K
5×5
0505
RTE
6.3
0J
0.33
R33
±15%
Y
6.3×5
0605
RLL
10
1A
0.47
R47
±20%
M
4×7
0407
MT1
16
1C
0.68
R68
-10～-30%
Q
5×7
0507
Lead Forming
ST1
25
1E
1.0
010
Others
T
6.3×7
0607
＆cut
STL
35
1V
2..2
2R2
8×7
0807
RLG
50
1H
3.3
3R3
5×11
0511
RZL
63
1J
4.7
4R7
6.3×11
0611
Forming lead to
RTV
80
1K
6.8
6R8
8×12
0812
right side
RTV
100
2A
10
100
8×14
0814
Forming lead to
RTK
160
2C
22
220
8×16
0816
left side
RTG
180
2J
33
330
10×12
1012
Taping F=5mm
REB
200
2D
47
470
10×16
1016
(4Ф~8Ф)
REF
220
2P
68
680
10×20
1020
Taped
RXG
250
2E
100
101
13×20
1320
Straight-pack
RXZ
315
2F
220
221
13×25
1325
Taping F=2.5mm
RXF
330
2U
330
331
13×35
1335
(4Ф~5Ф)
350
2V
470
471
16×31
1631
Name
400
2G
680
681
16×36
1636
420
2M
1000
102
18×30
1830
450
2W
2400
242
18×36
1836
500
2H
3300
332
18×40
1840
550
2J
4700
472
600
2K
6800
682
10000
103
22000
223
33000
333
68000
683
RTV
Version
01
Kink & Cutting
Page
CB
CK
CN
CM
F1
F2
F3
10
9、Lead Forming Type 加工型式
9.1
Taping 编带
Code
F1
Reference
figure
φd
0.45
0.45
0.45
0.5（5*11） 0.5（6*11）
Code
F3
p
P0
P1
F
△h
W
W0
W1
W2
H
H0
D0
t
△h1
Name
RTV
Version
0.45
0.5(8*7)
0.5(8*12)
8*5
8*7
8*12
±0.05
±1.0
±0.3
±0.5
+0.6/-0.2
±1.0
±0.5
-±0.5
-±0.5
±0.5
±0.3
±0.2
±0.2
φ10
Figure 2
0.45
0.5(5*11)
5.6
1.5
4*5
4*7
Figure 3
0.45
0.45
0.5(6.3*11)
Case Size
5*5
5*7
5*11
0.45
0.5(8*7)
0.5(8*12)
0.60
4.6
3.5
3.85
5.0
8*5
8*7
Tol
Figure 2
--
0.45
0.45
0.5（5*11） 0.5(8*7)
12.7
12.7
5.1
2.5
0
18.0
12min
9.0
2.0 max
18.5（17.5）*
16.0
-4.0
0.6
0
01
Tol
--
12.7
12.7
5.1
2.5
0
18.0
12min
9.0
2.0 max
18.5（17.5）*
-4.0
0.6
0
5.35
2.0
Reference
figure
φd
Case Size
6.3*5
6.3*7
6.3*11
5*5
5*7
5*11
4*5
4*7
0.45
p
P0
P1
F
△h
W
W0
W1
W2
H
H0
D0
t
△h1
Tol
--
12.7
12.7
3.85
5.0
0
18.0
12min
9.0
2.0 max
18.5（17.5）*
16.0
4.0
0.6
0
Reference
figure
φd
8*5
8*7
8*12
Figure 1
p
P0
P1
F
△h
W
W0
W1
W2
H
H0
D0
t
△h1
Code
F2
Case Size
6.3*5
6.3*7
6.3*11
5*5
5*7
5*11
4*5
4*7
±0.05
±1.0
±0.3
±0.5
+0.6/-0.2
±1.0
±0.5
-±0.5
-±0.5
-±0.3
±0.2
±0.2
±0.05
±1.0
±0.3
±0.5
+0.6/-0.2
±1.0
±0.5
-±0.5
-±0.5
±0.5
±0.3
±0.2
±0.2
Page
11
9.2
Lead Cut& Lead Forming 端子切脚或成型
Case Size
Code
C
1
C
D
s±0.5
φ4
1.5
φ5
2.0
φ6.3
2.5
φ8
3.5
φ10
5.0
φ13
5.0
φ16
7.5
φ18
7.5
φ4
1.5
φ5
2.0
φ6.3
2.5
φ8
3.5
φ10
5.0
φ13
5.0
B
C
h±0.5
φ16
7.5
φ18
7.5
φ4
1.5
φ5
2.0
φ6.3
2.5
φ8
3.5
φ4
1.5
φ5
2.0
φ6.3
2.5
φ8
3.5
N
C
M
Name
h±0.3
h±0.5
K
C
Shape Figure
h
h±0.5
RTV
h±0.5
Version
01
Page
12
10、Packing quantity 包装数量
10.1
Straight capacitor 直引线型产品
Plastics bag
Inside packing box
Over-wrap box
packing quantity
packing quantity
packing quantity
塑料袋包装数量
内包装盒包装数量
外包装箱包装数量
Φ5×11
1000
15000
30000
Φ6.3×11
1000
10000
20000
Φ8×12/8×14
500
6000
12000
Φ8×16
500
5000
10000
Φ10×12
250
4000
8000
Φ10×16
250
3000
6000
Φ10×20
200
2600
5200
Φ10×25
200
2200
4400
Φ10×30
200
2000
4000
Φ13×20
150
1500
3000
Φ13×25
100
1400
2800
Φ18×30
100
1000
2000
Plastics bag
Inside packing box
Over-wrap box
packing quantity
packing quantity
packing quantity
塑料袋包装数量
内包装盒包装数量
外包装箱包装数量
Φ5×11
1000
20000
40000
Φ6.3×11
1000
15000
30000
Φ8×12
500
10000
20000
Φ8×14/8×16
500
6000
12000
Φ10×12
500
5000
10000
Φ10×16
250
4000
8000
Φ10×20/10×25/10×30
200
3000
6000
Φ13×20
150
1800
3600
Φ13×25
100
1500
3000
Φ18×30
100
1000
2000
Parys Diameter
壳号
10.2
Cut capacitor 切脚型产品
Parys Diameter
壳号
10.3
Packahing specification 编带产品
Parys Diameter
Inside packing box packing quantity
Over-wrap box packing quantity
壳号
啤盒包装数量
外包装箱包装数量
Φ5×11/6.3×11
2000
20000
Φ8×12/8×14
1000
10000
Φ8×16
1000
8000
Φ10×12/10×1610×20/10×25
500
4000
Φ13×20/13×25
400
3200
Name
RTV
Version
01
Page
13
11、OTHER REMARKS 其它说明
11.1 铝电解电容器使用注意事项 IMPORTANT INFORMATION ON THE APPLICATION
OF ALUMINUM ELECTROLYTIC CAPACITORS
(1)直流铝电解电容器应按正确的极性使用 DC aluminum electrolytic capacitors are normally polarized
当直流铝电解电容器按反极性接入电路时，电容器会导致电子线路短路，由此产生的电流会引致电容器
损坏。若电路中有可能在负引线施加正电压，请选无极性产品。
When reverse voltage is applied on DC aluminum electrolytic capacitor ,the circuit will be short out and the
capacitor will be damaged due to abnormal current flows through the capacitor. Please use non- polar types of
capacitors when the positive voltage is applied on the cathode terminal.
(2)在额定工作电压以下使用 Use capacitor within rated voltage
当电容器上所施加电压高于额定工作电压时，电容器的漏电流将上升，其电气特性将在短时内劣化直至
损坏。请注意电压峰值勿超出额定工作电压。
When capacitor is used at higher voltage than the rated voltage, leakage current may increase and
characteristics may be drastically deteriorated and damaged in a short period. Please take extra caution that the
peak voltage should not exceed the rated voltage.
(3)作快速充放电使用 Sudden charge and discharge
当常规电容器被用作快速充电用途,其使用寿命可能会因为容量下降,温度急剧上升等而缩减。
When aluminum electrolytic capacitors for general purpose-use are employed in rapid charge and discharge
application, its life expectancy may be shortened resulted from capacitance decrease, heat rise, etc.
(4)电容器贮存 Storage of the capacitor
①请保管在室温 5～35℃，湿度 75%以下的环境。
we recommend the following conditions for storage: Ambient temperature：5~35℃ ,Ambient humidity：12 个月时，需充电后再使用；
If storage life >12 months，the products need to be charged again before using;
(c) 存放时间超过 2 年的电解电容器应报废处理；
If Storage time > two years, the products need to be discarded;
(5)施加纹波电流应小于额定值 Use capacitor within rated ripple current
施加纹波电流超过额定值后，会导致电容器体过热，容量下降，寿命缩短。所施加纹波电压的峰值应小
于额定工作电压。
If excessive ripple current is applied on the capacitor, which will result in generating excessive heat inside,
reducing capacitance and shortening life of capacitor. Therefore the peak value of the ripple voltage should be
less than the rated value.
(6)使用环境温度 Ambient temperature
铝电解电容器的使用寿命会受到环境温度的影响。据科学统计，使用环境温度下降 10℃其使用寿命增加
1 倍。
Life of aluminum electrolytic capacitor is affected by the ambient temperature. It is generally known that the
life doubles for each 10℃ decrease in temperature.
(7)引出线强度 Tensile strength of lead wire
当拉力施加到电容器引出线，该拉力将作用于电容器内部，这可能导致电容器内部短路，开路或漏电流
上升。在电容器焊装到电路板，请勿强烈摇动电容器。
When a strong force is applied to the lead wires or terminals, stress is put on the internal
connections, which may result in short circuit, open circuit or leakage current increase. Therefore it is not
advisable to bend or handle a capacitor after it has been soldered to the PC board.
Name
RTV
Version
01
Page
14
(8)焊接过程耐热性 Heat resistance at the soldering process
铝电解电容器装至电路板进行浸焊或波峰焊时，其塑料套管可能因焊接时间过长、温度过高而发生破裂
或二次收缩。
During soldering process, secondary shrinkage or sleeve crack may occur when soldering temperature is too
high or soldering time is too long.
(9)电路板的安装孔孔距及安装位置 Hole pitch and position of PC board
电路板安装孔的设计应与产品说明书的引线脚距相一致，如果将电容器强行插入孔距不配套的电路板，
那么会有应力作用于引出线，这可能导致短路或漏电流上升。
When designig a PC board , its hole pitch should be designed to coincide with the lead pitch (lead spacing) of
the capacitor specified in the catalog or specifications.When a capacitor is forcibly inserted into an unmatched
hole pitch, a force will put on the leads and which could result in a short circuit or increased leakage current.
(10) 关于焊接以后的清洗 Cleaning after soldering
① 电容器不能用卤化有机物系列的清洗剂进行清洗。如果必须进行清洗，请使用能够保证电容器质量的
清洗剂。
The aluminum electrolytic capacitors should be free of halogenated solvents during board cleaning after
soldering. Use solvent proof capacitors when halogenated solvents are used.
② 对于能够保证电容器质量的清洗剂，清洗后请不要在清洗溶液或者密封容器中保管。清洗后的电容器
请和电路板一起在热风下干燥 10 分钟以上，热风的温度不可高于电容器规定上限温度。
After cleaned with the solvent which can guarantee the quality of capacitors, the capacitors should not be kept in
solvent environments of non-ventilated places. Let the capacitors after cleaning dry with hot blast fully above
10mins and the temperature of hot blast should not be over than specified upper limit of that of capacitors.
(11) 关于固定剂以及镀层（涂层剂）Adhesives、fixative and coating materials(coating agent)
① 请不要使用含有卤化有机物系列的固定剂及镀层（涂层剂）。
Do not use halogenated adhesives and coating materials to fix aluminum electrolytic capacitors.
② 请不要让固定剂及镀层（涂层剂）将电容器封口部位（端子一侧）全部封住。
Do not cover up all the sealing area of capacitors with adhesives、fixative or coating materials (coating agent),
make coverage only partial.
11.2 符合 RoHS
RoHS compliance
符合欧盟 RoHS 的最新标准，若客户有特殊要求，按照双方签订的相关协议为准。
Completely in accordance with the latest standard of RoHS or relevant agreements reached by both parts if
customer has special requirements.
Name
RTV
Version
01
Page
15
工商网监
湘ICP备2023018690号
