User's Guide
SLVUAF8C – June 2015 – Revised November 2015
TPS65982 Evaluation Module
This document is the user’s guide for the TPS65982 Evaluation Module (TPS65982-EVM). The
TPS65982-EVM allows for evaluation of the TPS65982 IC as part of a stand-alone testing kit and for
development and testing of USB Type-C and Power Delivery (PD) end products.
1
2
3
4
5
6
7
8
9
Contents
About this Manual............................................................................................................ 4
Information About Cautions and Warnings ............................................................................... 4
Items Required for Operation .............................................................................................. 4
Introduction ................................................................................................................... 5
4.1
Using the TPS65986 on the TPS65982-EVM ................................................................... 5
Setup .......................................................................................................................... 8
5.1
Header, Jumper, Switch, Push Button and Test Point Descriptions ......................................... 8
5.2
LED Descriptions .................................................................................................. 10
5.3
Getting Started Using the TPS65982-EVM ................................................................... 11
Schematic ................................................................................................................... 29
Board Layout ................................................................................................................ 31
Bill of Materials ............................................................................................................. 35
Firmware Installation ....................................................................................................... 38
Tiva, Code Composer Studio, Thunderbolt are trademarks of Texas Instruments.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
1
www.ti.com
9.1
9.2
9.3
9.4
9.5
9.6
9.7
9.8
Writing a Flash Image Using an Aardvark SPI Programmer ...............................................
Wire Aardvark to SPI Pins for Flash on the TPS65982-EVM board ........................................
Run “Flash Center”.exe ...........................................................................................
Add Adapter ........................................................................................................
Choose Target (Device Type) ...................................................................................
Load Binary File ...................................................................................................
Program TPS65982-EVM ........................................................................................
Verify (Optional) ...................................................................................................
38
39
39
40
41
42
43
43
List of Figures
1
TPS65982-EVM (Top View) ................................................................................................ 6
2
TPS65982-EVM (Bottom View) ............................................................................................ 7
3
TPS65982-EVM Schematic Page 1
29
4
TPS65982-EVM Schematic Page 2
30
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
.....................................................................................
.....................................................................................
PCB Layer 1 (Top Layer)..................................................................................................
PCB Layer 1 (Component View) .........................................................................................
PCB Layer 2 (GND Plane) ................................................................................................
PCB Layer 3 (Inner Signal Layer 1) .....................................................................................
PCB Layer 4 (GND Plane) ................................................................................................
PCB Layer 5 (Inner Signal Layer 2) .....................................................................................
PCB Layer 6 (Bottom Layer) ..............................................................................................
PCB Layer 6 (Component View) .........................................................................................
Legend .......................................................................................................................
Aardvark Wired to SPI Pins ...............................................................................................
Flash Center GUI ..........................................................................................................
Add Adapters... Button.....................................................................................................
Add Adapters Selection ...................................................................................................
Adapter Detection ..........................................................................................................
Select Target Device .......................................................................................................
Loading Data Section of Flash Center ..................................................................................
Programming the TPS65982-EVM .......................................................................................
Verifying Binary Image.....................................................................................................
31
31
32
32
33
33
34
34
38
39
39
40
40
40
41
42
43
43
List of Tables
1
Device and Package Configurations ...................................................................................... 5
2
TPS65982-EVM Configuration Table .................................................................................... 13
3
Configuration ID 0 .......................................................................................................... 14
4
Configuration ID 1 .......................................................................................................... 15
5
Configuration ID 2 .......................................................................................................... 16
6
Configuration ID 3 .......................................................................................................... 17
7
Configuration ID 4 .......................................................................................................... 18
8
Configuration ID 5 .......................................................................................................... 19
9
Configuration ID 6 .......................................................................................................... 20
10
Configuration ID 7 .......................................................................................................... 21
11
Configuration ID 8 .......................................................................................................... 22
12
Configuration ID 9 .......................................................................................................... 23
13
Configuration ID 10
24
14
Configuration ID 11
25
15
16
2
........................................................................................................
........................................................................................................
Configuration ID 12 ........................................................................................................
Configuration ID 13 ........................................................................................................
TPS65982 Evaluation Module
26
27
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
www.ti.com
17
18
19
........................................................................................................
Configuration ID 15 ........................................................................................................
Bill of Materials .............................................................................................................
Configuration ID 14
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
27
28
35
3
About this Manual
1
www.ti.com
About this Manual
This user’s guide describes the TPS65982-EVM. This guide contains an introduction, setup instructions,
the EVM schematic, top and bottom board layouts and component views, internal VDD and GND plane
layouts, and a bill of materials (BOM).
2
Information About Cautions and Warnings
ATTENTION
STATIC SENSITIVE DEVICES
HANDLE ONLY AT
STATIC SAFE WORK STATIONS
CAUTION
This EVM contains components that can potentially be damaged by
electrostatic discharge. Always transport and store the EVM in its supplied ESD
bag when not in use. Handle using an antistatic wristband. Operate on an
antistatic work surface. For more information on proper handling, see the
Electrostatic Discharge (ESD) application note (SSYA008).
The information in a caution or a warning is provided for your protection. Read each caution and warning
carefully.
3
Items Required for Operation
The following items are required to use the TPS65982-EVM:
• TPS65982 (SLVSD02) datasheet
• TPS65982-EVM
• Barrel jack AC Adapter, DC power supply, or Tiva™ C-Series LaunchPad to supply power
The following items are recommended for developing firmware for an attached processor to control the
TPS65982-EVM:
• Tiva C-Series EK-TM4C123GXL LaunchPad
• USB standard-A to mini-B cable
• Computer with Code Composer Studio™ installed
4
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Introduction
www.ti.com
4
Introduction
This document is the user’s guide for the TPS65982-EVM.
The TPS65982-EVM allows a simple way to evaluate the TPS65982. The TPS65982-EVM is built with a
USB Type-C receptacle and TPS65982 to detect another TPS65982-EVM or other Type-C host/device via
a USB Type-C cable. The TPS65982 detects the plug event and/or presence of another Type-C product
on the CC1 or CC2 pin and provides or consumes power on the VBUS pin. The TPS65982-EVM also
supports dead battery mode and can be powered by another TPS65982-EVM or other USB Type-C power
provider. After CC detection and Type-C power is established, the TPS65982 will attempt to negotiate a
USB Power Delivery (PD) contract to provide or consume additional power. After a USB PD contract is
negotiated, the TPS65982 will attempt to enter an Alternate Mode. The TPS65982-EVM can be used to
emulate other USB Type-C and PD products, such as a dock, a notebook computer, a tablet, a dongle, an
AC charger adapter, and a high-power bus-powered device. The GPIOs of the TPS65982 are routed to
the EVM J2 and J3 headers and can also be used to control external SuperSpeed and DisplayPort
multiplexers.
4.1
Using the TPS65986 on the TPS65982-EVM
The TPS65986 is a pin-to-pin compatible device and is drop-in replaceable with the TPS65982. The
following list shows the differences and similarities between the TPS65982 and TPS65986:
• TPS65982 and TPS65986 firmware can be used in both devices
– Note that some functions may not be present
• TPS65986 does not have the PP_EXT FET control from the TPS65982
• TPS65986 does not have the secondary I2C port from the TPS65982
Table 1. Device and Package Configurations
EVM Annotation
IC
Package
U2
TPS65982ABZQZR
BGA (96 pins)
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
5
Introduction
www.ti.com
Figure 1. TPS65982-EVM (Top View)
6
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Introduction
www.ti.com
Figure 2. TPS65982-EVM (Bottom View)
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
7
Setup
5
www.ti.com
Setup
This section describes the header/jumper connections on the EVM and getting started using the
TPS65982-EVM.
5.1
Header, Jumper, Switch, Push Button and Test Point Descriptions
The headers, jumpers, switches, push buttons, and test points are listed in the order they can be found on
the PCB, from top left to bottom right, across then down. However, related jumpers/headers/test points are
listed simultaneously.
5.1.1
S1: Switch Bank #1
Switch bank S1 contains four DIP switches, three of which are used to control the three bits/pins [B2:B0]
of the configuration options for the TPS65982-EVM, shown in Table 2. Bit [B0] is connected to the GPIO1
pin of the TPS65982 IC (U2) and is pulled low when the upper-most switch is pushed to the left-hand side,
pin 1 of S1. Bit [B0] is pulled high when the upper-most switch is pushed to the right-hand side, pin 8 of
S1. Bit [B1] is connected to the DEBUG3 pin of the TPS65982 IC (U2) and is pulled low when the middleupper switch is pushed to the left-hand side, pin 2 of S1. Bit [B1] is pulled high when the middle-upper
switch is pushed to the right-hand side, pin 7 of S1. Bit [B2] is connected to the DEBUG4 pin of the
TPS65982 IC (U2) and is pulled low when the middle-lower switch is pushed to the left-hand side, pin 3 of
S1. Bit [B2] is pulled high when the middle-lower switch is pushed to the right-hand side, pin 6 of S1. Bit
[B3] is connected to the TPS65982 IC (U2), however, is not used for any configuration.
5.1.2
S2 (Not Populated): Switch Bank #2
Switch bank S2 contains four DIP switches which are used to control four bits/pins [B3:B0] of the
TPS65982-EVM. Bit [B0] is connected to the DEBUG_CTL1 pin of the TPS65982 IC (U2) and is pulled
low when the upper-most switch is pushed to the left-hand side, pin 1 of S1. Bit [B0] is pulled high when
the upper-most switch is pushed to the right-hand side, pin 8 of S1. Bit [B1] is connected to the
DEBUG_CTL2 pin of the TPS65982 IC (U2) and is pulled low when the middle-upper switch is pushed to
the left-hand side, pin 2 of S1. Bit [B1] is pulled high when the middle-upper switch is pushed to the righthand side, pin 7 of S1. Bit [B2] is connected to the BUSPOWERZ and LDO_3V3 pins of the TPS65982 IC
(U2) while bit [B3] is connected to the BUSPOWERZ and LDO_1V8D pins of the TPS65982 IC (U2).
BUSPOWERZ is pulled low when the middle-lower and lowest switches are pushed to the left-hand side,
pins 3 and 4 of S1. Bit [B2] is pulled high and BUSPOWERZ is pulled up to LDO_3V3 when the middlelower switch is pushed to the right-hand side, pin 6 of S1. Bit [B3] is pulled high and BUSPOWERZ is
pulled up to LDO_1V8D when the lowest switch is pushed to the right-hand side, pin 5 of S1. The middlelower and lowest switches of S1, bits [B2] and [B3] should never both be pushed to the right-hand side,
pins 6 and 5.
5.1.3
J7 (Not Populated): Tiva LaunchPad Power and System Power Jumpers
Jumper J7 is a set of 2 surface-mount jumpers to connect power from a LaunchPad to the System Power
rails of the TPS65982 IC (U2). Connecting a shunt between pins 1 and 2 will connect System_5V to
Tiva_5V and will allow the 5-V rail of the TPS65982-EVM to be powered by the 5-V rail of the Tiva
LaunchPad. Connecting a shunt between pins 3 and 4 will connect System_3V3 to Tiva_3V3 and will
allow the 3.3-V rail of the TPS65982-EVM to be powered by the 3.3-V rail of the Tiva LaunchPad. Both of
these shunts can be connected simultaneously.
5.1.4
J4: Barrel Jack Receptacle for 20-V AC Adapter
Receptacle J4 is intended to mate with a barrel-jack plug that will provide 20-V DC that has been rectified
by an AC Adapter. The size, polarity, and voltage of the plug must match in order to safely provide power
to the External Power rail TPS65982-EVM. A standard Dell or HP notebook adapter or similar will provide
the needed power. For example, the Dell 130W Part Number: 492-BBGP.
8
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.1.5
S3: RESET Push-Button
Switch S3 is a push-button that will pull the HREST pin (D6) of the TPS65982 IC (U2) high when pressed.
Releasing the push-button will pull HRESET low again and the TPS65982 IC (U2) will go through a
hardware reset and reload firmware from the non-volatile memory of the Flash IC (U1).
5.1.6
J2 and J3: LaunchPad Receptacles
Receptacles J2 and J3 allow the TPS65982-EVM to interface with a standard TI LaunchPad. See the
TPS65982-EVM schematic in Figure 4 and Figure 4 to determine which signals from the LaunchPad are
connected to the TPS65982 IC (U2), or refer to Section 5.3.3 for a description of these connections.
5.1.7
TP5 and TP4 (GND): Ground (GND) Test Points
Test points TP4 and TP5, labeled GND, are connected to signal ground which is also connected to the
GND pins of the TPS65982 IC (U2). There are two test points on the board for easy attachment of
oscilloscope or multimeter ground connections. They are both connected directly to the signal ground
plane. Power, analog signals, and digital signals are all directly connected to GND.
5.1.8
TP3 (VBUS): VBUS Test Point
Test point TP3 provides a location to probe the voltage on VBUS, the input or output power rail connected
at the Type-C receptacle (J1).
5.1.9
TP2 (CC2): CC2 Test Point
Test point TP2 provides a location to probe the voltage on CC2, the secondary Cable Connection signal
connected at the Type-C receptacle (J1). When a Type-C cable is plugged in upside-down, the CC2 signal
is connected to the CC wire of the cable and the CC1 pin of the TPS65982 IC (U2). When a cable is
plugged in right-side up, the CC2 signal is connected to the VCONN wire of the cable and the CC2 pin of
the TPS65982 IC (U2).
5.1.10
TP1 (CC1): CC1 Test Point
Test point TP1 provides a location to probe the voltage on CC1, the primary Cable Connection signal
connected at the Type-C receptacle (J1). When a Type-C cable is plugged in right-side up, the CC1 signal
is connected to the CC wire of the cable and the CC1 pin of the TPS65982 IC (U2). When a cable is
plugged in upside-down, the CC1 signal is connected to the VCONN wire of the cable and the CC2 pin of
the TPS65982 IC (U2).
5.1.11
J6 (PP_EXT ENABLE): PP_EXT to External Power Jumper
Jumper J6 is a jumper which connects power from the External Power rail provided at J4 to the PP_EXT
external NexFETS (Q1 and Q2) rated for 20 V and 5 A of current. Pin 1 of this jumper is connected to J4
and pin 2 is connected to the External Power rail of the system; therefore, if this jumper is shunted and a
20-V DC power supply is connected, the external DC power supply will provide the External Power rail to
the system and to the PP_EXT external FET path.
5.1.12
J5 (Not Populated): Header for System_3V3, System_5V, and HV_Source
Header J5 is not populated, but provides test points for probing the voltage on the HV_Source rail at pin 1
(marked by rectangular pad), the voltage on the System_5V rail at pin 2, and the voltage on the
System_3V3 rail at pin 3. If J5 is installed, a DC power supply may also be used to apply 12 V to the
HV_Source rail, 5 V to the System_5V rail, and/or 3.3 V to the System_3V3 rail when J4 is not used, J6 is
not used, and/or J7 is not used to provide power to these rails of the system.
5.1.13
J1: USB Type-C Receptacle
Receptacle J1 is the USB Type-C port where a USB Type-C cable can be plugged into the TPS65982EVM.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
9
Setup
5.2
www.ti.com
LED Descriptions
The headers, jumpers, switches, push buttons, and test points are listed in the order they can be found on
the PCB, from top left to bottom right, across then down. However, related jumpers/headers/test points are
listed simultaneously.
5.2.1
D2: CC1 Cable Orientation Indicator (White LED)
LED D2, labeled CC1, is an indicator of the cable orientation which is ON when the USB Type-C cable is
inserted right-side up.
5.2.2
D3: CC2 Cable Orientation Indicator (White LED)
LED D3, labeled CC2, is an indicator of the cable orientation which is ON when the USB Type-C cable is
inserted upside-down.
5.2.3
D4: DisplayPort (A) Indicator (White LED)
LED D4, labeled A, is an indicator that the TPS65982-EVM has established a Power Delivery contract and
entered the alternate mode, DisplayPort. This indicator will blink ON and OFF when 2 Lane DisplayPort
alternate mode is entered and will remain solid when 4 Lane DisplayPort alternate mode is entered.
5.2.4
D5: Thunderbolt™ and APP FW Loaded Indicator (White LED)
LED D5, labeled B, is an indicator that the application firmware has loaded on the TPS65982-EVM. When
the TPS65982-EVM is powered up and connected to no other device, and the App FW has successfully
loaded it, the LED will be ON. This indicator will blink ON and OFF when a USB PD contract has been
negotiated and the Thunderbolt alternate mode has been entered.
5.2.5
D6: Consumer (CONS) Indicator (White LED)
LED D6, labeled CONS, is an indicator of the consumer/provider role which is ON when the TPS65982 IC
(U2) has negotiated a USB PD contract to be a power consumer, or sink.
5.2.6
D7: Provider Indicator (White LED)
LED D7, labeled PVDR, is an indicator of the USB PD voltage which is ON when a USB PD contract has
been negotiated for 5 V as a provider.
5.2.7
D8: 5 Volts (5V) Power Indicator (White LED)
LED D8, labeled 5V, is an indicator of the USB PD voltage which is ON when a USB PD contract has
been negotiated for 5 V as a provider.
5.2.8
D9: High Voltage (HV) Power Indicator (White LED)
LED D9, labeled HV, is an indicator of the USB PD voltage which is ON when a USB PD contract has
been negotiated for 12 V as a provider. This indicator will blink ON and OFF when a USB PD contract has
been negotiated for 20 V as a provider or consumer.
10
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3
Getting Started Using the TPS65982-EVM
5.3.1
Powering the TPS65982-EVM
There are many viable options for providing power to the TPS65982-EVM. Sections Section 5.3.1.1
through Section 5.3.1.5 describe all of these options for powering the EVM.
5.3.1.1
Powering the EVM From J4
When a barrel jack plug of the appropriate voltage, size, and polarity is inserted in J4, all of the power rails
of the TPS65982-EVM (System_3V3, System_5V, and HV_Source) will automatically be generated by the
DCDC buck converters (U5, U6, and U7, respectively) from the External Power rail. When a shunt is
installed on J6, the External Power rail will also provide power to the PP_EXT FETs (Q1 and Q2).
5.3.1.2
Powering the EVM From J6
When a shunt is installed on J6 and a 20-V DC power supply is connected to either pin, the External
Power rail will generate all of the power rails for the TPS65982-EVM and will also provide power to the
PP_EXT FETs (Q1 and Q2).
5.3.1.3
Powering the EVM From J7 and J5
When J4 and J6 are not used and a Tiva LaunchPad is used, both shunts on Jumper J7 should be
installed to provide power to the System_3V3 and System_5V power rails of the TPS65982-EVM from a
LaunchPad’s 3.3-V and 5-V rails, labeled Tiva_3V3 and Tiva_5V. When power is provided by a
LaunchPad, 12 V can be supplied to the HV_Source rail by a DC power supply at pin 1 of J5.
5.3.1.4
Powering the EVM From J6 and J5
When J6 is not used to supply power to External Power and a LaunchPad is not used, the 20-, 12-, 5-,
and 3.3-V rails can all be supplied by a DC power supply. 20 V should be applied to PP_EXT at pin 2 of
J6, 12 V should be applied to HV_Source at pin 1 of J5, 5 V should be applied to System_5V at pin 2 of
J5, and 3.3 V should be applied to System_3V3 at pin 3 of J5.
5.3.1.5
Power the EVM from the USB Type-C Port
When a 0-Ω resistor is installed at R10 and R11, RPD_G1 and RPD_G2 are shorted to CC1 and CC2
respectively, and dead battery mode is supported by the TPS65982-EVM. Depending on the configuration
used (see Table 2), the TPS65982-EVM will negotiate a USB PD contract for 5 V at 3 A, 12 V at 3 A,
12–20 V at 3 A, 20 V at 3 A, or 20 V at 5 A and will provide power to portions of the system depending on
whether the PP_EXT external FET or PP_HV internal FET is used to sink power.
NOTE: When a USB PD contract is negotiated for 5 V, it is common for the LEDs to blink due to the
switching behavior of the buck converter U6, which produces the System_5V rail. When
blinking on the LEDs occurs, VBUS is stable at 5 V and can be measured on test point TP3.
5.3.2
Analyzing USB Type-C and PD Events Using the LEDs
When a USB Type-C cable is inserted into the USB Type-C receptacle (J1), the LEDs on the TPS65982EVM (D2–D9 described in Section 5.2.1–Section 5.2.8) can be used to interpret what type of event has
occurred and, in turn, what type of device is connected at the other end of the Type-C cable.
5.3.2.1
Cable Orientation (CC1 or CC2) Event
After a plug event (a correctly terminated USB Type-C cable has been connected with a USB Type-C
product on the opposite end of the cable) has occurred, cable orientation detection of the USB Type-C
cable will occur. When cable orientation detection has completed, this event will occur and either LED D2
(CC1) or LED D3 (CC2) will turn ON to indicate that the cable is inserted right-side up (CC1 ON and CC2
OFF) or upside-down (CC2 ON and CC1 OFF).
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
11
Setup
www.ti.com
5.3.2.2
Consumer or Provider (CONS or PRVDR) Event
After a plug event has occurred and cable orientation detection is complete, a USB PD contract will be
negotiated. When a USB PD contract has been successfully negotiated, this event will occur and either
LED D7 (CONS) or LED D6 (PVDR) will turn ON to indicate that the TPS65982-EVM is acting as a power
consumer (CONS ON and PVDR OFF) or power provider (PVDR ON and CONS OFF).
5.3.2.3
USB PD Voltage (5V, HV, or Blinking HV) Event
After a plug event has occurred, cable orientation detection is complete, and a USB PD contract has been
negotiated, a voltage will be present on VBUS (TP3) at the USB Type-C port (J1). When VBUS is present,
this event will occur and one of the following LED indicators may be ON or blinking ON or OFF: LED D8
(5V) or LED D9 (HV). If the TPS65982 is acting as a power provider and the voltage on VBUS is 5 V, LED
D8 (5V) will be ON. If the TPS65982 is acting as a power provider and the voltage on VBUS is 12 V, LED
D9 (HV) will be ON. If the TPS65982 is acting as a power consumer or provider and the voltage on VBUS
is 20 V, LED D9 (HV) will be blinking ON and OFF.
5.3.2.4
DisplayPort Alternate Mode (LED A) Event
When a USB PD contract has been negotiated to enter an alternate mode for DisplayPort video, LED A
(D4) will blink ON and OFF every 1 second to indicate that 2-lane DisplayPort alternate mode has been
entered, and if LED A (D4) remains solid then 4 lane DisplayPort alternate mode has been entered.
5.3.2.5
Thunderbolt Alternate Mode (LED B) Event
When a USB PD contract has been negotiated to enter an alternate mode for Thunderbolt video+data,
LED B (D5) will blink On and OFF every 1 second to indicate that this event has occurred.
12
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3
TPS65982-EVM Configuration Table Overview
Configuring the TPS65982-EVM to power-on, initialize, and emulate application types is outlined in
Table 2, and is as simple as changing the position of the top 3 DIP switches on switch bank S1. Resetting
the TPS65982 IC (U2), reloading the FW in the Flash IC (U1), and re-initializing by reading the S1 DIP
switch positions can be accomplished by pressing and releasing push-button S3. A detailed description of
each of the TPS65982-EVM configurations settings controlled by S1 can be found in Section 5.3.3.1
through Section 5.3.3.16.
Table 2. TPS65982-EVM Configuration Table
* Configuration compatible with the TPS65986
NOTE: To achieve 5 A, an active or electronically marked cable is needed.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
13
Setup
www.ti.com
5.3.3.1
Configuration ID 0: Docking System
Table 3. Configuration ID 0
5.3.3.1.1
Overview
The TPS65982-EVM will power-on and initialize into configuration ID 0 when all 4 of the DIP switches
[B0:B3] on switch bank S1 are pushed to the left-hand side. Configuration ID 0 is designed to model a
docking system application.
A TPS65982-EVM configured as a dock is capable of providing (sourcing) power. The fully-featured TypeC port of a dock which faces a laptop can be an upstream-facing port (UFP) for DisplayPort video, which
is also emulated by this EVM configuration. This configuration will also initiate a PD power role swap to
source and/or a PD data role swap to UFP.
5.3.3.1.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A, 12 V at 3 A through the
PP_HV internal FET path, and 20 V at 5 A through the PP_EXT external FET path.
5.3.3.1.3
Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 0 A.
5.3.3.1.4
Video Capabilities
This configuration is capable of negotiating a USB PD alternate mode contract for DisplayPort video as an
upstream-facing port (UFP). An alternate mode contract will only be negotiated successfully when
connected to a product which is capable of DisplayPort video as a downstream-facing port (DFP).
5.3.3.1.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 3 for providing power and
entering DisplayPort alternate mode. This configuration is also compatible with a TPS65982-EVM using
configuration ID 1 for providing power and entering DisplayPort alternate mode. These TPS65982-EVM
configurations respectively emulate notebook, tablet, and charger-adapter applications and the same
performance is expected when connected to actual applications of these products.
14
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.2
Configuration ID 1: Tablet (or Ultrabook)
Table 4. Configuration ID 1
5.3.3.2.1
Overview
The TPS65982-EVM will power-on and initialize into configuration ID 1 when the 1st DIP switch [B0] on
switch bank S1 is pushed to the right-hand side and the 2nd (middle), 3rd, 4th DIP switches [B1], [B2], and
[B3] on switch bank S1 are pushed to the left-hand side. Configuration ID 1 is designed to model a tablet
(or Ultrabook) application.
A TPS65982-EVM configured as a tablet is capable of providing (sourcing) power or consuming (sinking)
power. A fully-featured Type-C port on a tablet can be capable as a downstream-facing port (DFP) for
DisplayPort video, which is also emulated by this EVM configuration. This configuration will also initiate a
PD power role swap to sink and/or a PD data role swap to DFP.
5.3.3.2.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 1.5 A only through the PP_5V0
internal FET path.
5.3.3.2.3
Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 3 A and 12 to 20 V at 3 A through
the PP_HV internal FET path.
5.3.3.2.4
Video Capabilities
This configuration pairs ideally with a TPS65982-EVM using configuration ID 0 for consuming or providing
power and entering DisplayPort alternate mode. This configuration is also compatible with a TPS65982EVM using configuration ID 4 for providing power and entering DisplayPort alternate mode. To test this
configuration as a power consumer which enters USB2.0 and 3.1 for data, pair it with a TPS65982-EVM
using configuration ID 6. These TPS65982-EVM configurations respectively emulate dock, dongle, and
charger-adapter applications and the same performance is expected when connected to actual
applications of these products.
5.3.3.2.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 0 for consuming power and
entering DisplayPort alternate mode. This configuration is also compatible with a TPS65982-EVM using
configuration ID 4 for providing power and entering DisplayPort alternate mode. These TPS65982-EVM
configurations respectively emulate dock, dongle, and charger-adapter applications and the same
performance is expected when connected to actual applications of these products.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
15
Setup
www.ti.com
5.3.3.3
Configuration ID 2: Notebook (or Mobile Workstation) with Thunderbolt Mode Capabilities
Table 5. Configuration ID 2
5.3.3.3.1
Overview
The TPS65982-EVM will power-on and initialize into configuration ID 2 when the 1st, 3rd, and 4th DIP
switches [B0],[B2], [B3] on switch bank S1 are pushed to the left-hand side and the 2nd DIP switch [B1] on
switch bank S1 is pushed to the right-hand side. Configuration ID 2 is designed to model a Thunderbolt
notebook (or mobile workstation) application.
A TPS65982-EVM configured as a notebook is capable of providing (sourcing) power or consuming
(sinking) power. A fully-featured Type-C port on a notebook can be capable as a downstream-facing port
(DFP) for DisplayPort video and Thunderbolt Alternate Mode video+data, which is also emulated by this
EVM configuration. This configuration will also initiate a PD power role swap to sink and/or a PD data role
swap to DFP.
5.3.3.3.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path and 12 V at 3 A through the PP_HV internal FET path.
5.3.3.3.3
Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 0 A and 20 V at 3 A through the
PP_EXT external FET path.
5.3.3.3.4
Video Capabilities
This configuration is capable of negotiating a USB PD Thunderbolt Alternate Mode contract for video+data
as a downstream-facing port (DFP). This configuration is also capable of negotiating a USB PD alternate
mode contract for DisplayPort video as a downstream-facing port (DFP). An alternate mode contract will
only be negotiated successfully when connected to a product which is capable of Thunderbolt Alternate
Mode or DisplayPort video as an upstream-facing port (UFP).
5.3.3.3.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 5 for consuming or providing
power and entering Thunderbolt Alternate Mode. This configuration is also compatible with a TPS65982EVM using configuration ID 4 for providing power and entering DisplayPort alternate mode. To test this
configuration as a power consumer which enters USB2.0 and 3.1 for data, pair it with a TPS65982-EVM
using configuration ID 6. These TPS65982-EVM configurations respectively emulate dock, dongle, and
charger-adapter applications and the same performance is expected when connected to actual
applications of these products.
16
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.4
Configuration ID 3: Notebook (or Mobile Workstation) That can Pass AC-Adapted Power
Table 6. Configuration ID 3
5.3.3.4.1
Overview
The TPS65982-EVM will boot up and initialize into configuration ID 3 when the 1st and 2nd DIP switches
[B0] and [B1] on switch bank S1 are pushed to the right-hand side and the 3rd and 4th DIP switch [B2] and
[B3] on switch bank S1 is pushed to the left-hand side. Configuration ID 3 is designed to model a
notebook (or mobile workstation) application that can pass AC-adapted power as a provider.
A TPS65982-EVM configured as a notebook is capable of providing (sourcing) power or consuming
(sinking) power. A fully-featured Type-C port on a notebook can be capable as a downstream-facing port
(DFP) for DisplayPort video, which is also emulated by this EVM configuration. This configuration will also
initiate a PD power role swap to sink and/or a PD data role swap to DFP.
5.3.3.4.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path and 20 V at 3 A through the PP_EXT external FET path.
5.3.3.4.3
Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 0 A and 20 V at 3 A through the
PP_HV internal FET path.
5.3.3.4.4
Video Capabilities
This configuration is capable of negotiating a USB PD alternate mode contract for DisplayPort video as a
downstream-facing port (DFP). An alternate mode contract will only be negotiated successfully when
connected to a product which is capable of DisplayPort video as an upstream-facing port (UFP).
5.3.3.4.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 0 for consuming or providing
power and entering DisplayPort alternate mode. This configuration is also compatible with a TPS65982EVM using configuration ID 4 for providing power and entering DisplayPort alternate mode. To test this
configuration as a power consumer which enters USB2.0 and 3.1 for data, pair it with a TPS65982-EVM
using configuration ID 6. These TPS65982-EVM configurations respectively emulate dock, dongle, and
charger-adapter applications and the same performance is expected when connected to actual
applications of these products.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
17
Setup
www.ti.com
5.3.3.5
Configuration ID 4: Dongle
Table 7. Configuration ID 4
5.3.3.5.1
Overview
The TPS65982-EVM will boot up and initialize into configuration ID 4 when the 1st, 2nd, and 4th DIP
switches [B0], [B1], and [B3] on switch bank S1 are pushed to the left-hand side and the 3rd DIP switch
[B2] on switch bank S1 is pushed to the right-hand side. Configuration ID 4 is designed to model a dongle
application.
A TPS65982-EVM configured as a dongle is capable of consuming (sinking) power only. A fully-featured
Type-C port on a dongle can be capable as an upstream-facing port (UFP) for DisplayPort video, which is
also emulated by this EVM configuration.
5.3.3.5.2
Source Capabilities
This configuration is designed to be a consumer (sink) of power only, and therefore does not have any
source capabilities.
5.3.3.5.3
Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 900 milliamps through the PP_HV
internal FET path only.
5.3.3.5.4
Video Capabilities
This configuration is capable of negotiating a USB PD alternate mode contract for DisplayPort video as an
upstream-facing port (UFP). An alternate mode contract will only be negotiated successfully when
connected to a product which is capable of DisplayPort video as a downstream-facing port (DFP).
5.3.3.5.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 3 for consuming power and
entering DisplayPort alternate mode. This configuration is also compatible with a TPS65982-EVM using
configuration ID 1 for consuming power and entering DisplayPort alternate mode. These TPS65982-EVM
configurations respectively emulate notebook and tablet/Ultrabook applications and the same performance
is expected when connected to actual applications of these products.
18
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.6
Configuration ID 5: Docking System with Thunderbolt Mode Capabilities
Table 8. Configuration ID 5
5.3.3.6.1
Overview
The TPS65982-EVM will boot up and initialize into configuration ID 5 when the 1st and 3rd DIP switches
[B0] and [B2] on switch bank S1 are pushed to the right-hand side and the 2nd, and 4th DIP switches [B1]
and [B3] on switch bank S1 is pushed to the left-hand side. Configuration ID 5 is designed to model a
Thunderbolt docking system application.
A TPS65982-EVM configured as a dock is capable of providing (sourcing) power. The fully-featured TypeC port of a dock which faces a monitor can be a downstream-facing port (DFP) for DisplayPort video and
Thunderbolt Alternate Mode video+data, which is also emulated by this EVM configuration. This
configuration will initiate a PD power role swap to source.
5.3.3.6.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path, 12 V at 3 A through the PP_HV internal FET path, and 20 V at 5 A through the PP_EXT
external FET path.
5.3.3.6.3
Sink Capabilities
This configuration is capable of negotiating a PD contract to sink 5 V at 0 A.
5.3.3.6.4
Video Capabilities
This configuration is capable of negotiating a USB PD Thunderbolt Alternate Mode contract for video+data
as a downstream-facing port (DFP). This configuration is also capable of negotiating a USB PD alternate
mode contract for DisplayPort video as a downstream-facing port (DFP). An alternate mode contract will
only be negotiated successfully when connected to a product which is capable of Thunderbolt Alternate
Mode or DisplayPort video as an upstream-facing port (UFP).
5.3.3.6.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 2 for providing power and
entering Thunderbolt Alternate Mode for video+data. This configuration is also compatible with a
TPS65982-EVM using configuration ID 4 entering DisplayPort alternate mode. These TPS65982-EVM
configurations respectively emulate notebook and charger-adapter applications and the same performance
is expected when connected to actual applications of these products.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
19
Setup
www.ti.com
5.3.3.7
Configuration ID 6: Charger-Adapter (or AC Adapter)
Table 9. Configuration ID 6
5.3.3.7.1
Overview
The TPS65982-EVM will boot up and initialize into configuration ID 6 when the 1st and 4th DIP switches
[B0] and [B3]on switch bank S1 is pushed to the left-hand side and the 2nd and 3rd DIP switches [B1] and
[B2] on switch bank S1 are pushed to the right-hand side. Configuration ID 6 is designed to model a
charger-adapter application.
A TPS65982-EVM configured as a charger is capable of providing (sourcing) power only. A fully-featured
Type-C port on a charger can be capable of USB 2.0 and USB3.1 data, which is also emulated by this
EVM configuration.
5.3.3.7.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path, 12 V at 3 A through the PP_HV internal FET path, and 20 V at 0 A through the PP_EXT
external FET path.
5.3.3.7.3
Sink Capabilities
This configuration is designed to be a provider (source) of power only, and therefore does not have any
sink capabilities.
5.3.3.7.4
Video Capabilities
This configuration is capable of USB 2.0 and USB 3.1 data only, and therefore does not have any video
capabilities.
5.3.3.7.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 7 for providing power and
enters USB2.0 and 3.1 mode for data by default. This configuration is also compatible with a TPS65982EVM using configuration ID 2 or 3 for providing power and enters USB2.0 and 3.1 mode for data by
default. This configuration is also compatible with a TPS65982-EVM using configuration ID 2 for providing
power and enters USB2.0 and 3.1 mode for data by default. This configuration is also compatible with a
TPS65982-EVM using configuration ID 1 for providing power and enters USB2.0 and 3.1 mode for data by
default. These TPS65982-EVM configurations respectively emulate high-power bus-powered device,
notebook, dock, and tablet applications and the same performance is expected when connected to actual
applications of these products.
20
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.8
Configuration ID 7: High-Power Bus-Powered Device
Table 10. Configuration ID 7
5.3.3.8.1
Overview
The TPS65982-EVM will boot up and initialize into configuration ID 7 when [B0], [B1], and [B2] of the DIP
switches on switch bank S1 are pushed to the right-hand side and [B3] is pushed to the left. Configuration
ID 7 is designed to model a high-power bus-powered device application.
A TPS65982-EVM configured as a high-power bus-powered device is capable of consuming (sinking)
power only. A fully-featured Type-C port on a high-power bus-powered device can be capable of USB 2.0
and USB3.1 data, which is also emulated by this EVM configuration.
5.3.3.8.2
Source Capabilities
This configuration is designed to be a consumer (sink) of power only, and therefore does not have any
source capabilities.
5.3.3.8.3
Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 3 A, 12 V at 3 A, 20 V at 5 A
through the PP_EXT external FET path.
5.3.3.8.4
Video Capabilities
This configuration is capable of USB 2.0 and USB 3.1 data only, and therefore does not have any video
capabilities.
5.3.3.8.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 6 for consuming power and
enters USB2.0 and 3.1 mode for data by default. This configuration is also compatible with a TPS65982EVM using configuration ID 0 or 5 for consuming power and entering USB2.0 and 3.1 mode for data by
default. This configuration is also compatible with a TPS65982-EVM using configuration ID 2 or 3 for
consuming power and entering USB2.0 and 3.1 mode for data by default. These TPS65982-EVM
configurations respectively emulate charger-adapter, dock, and notebook applications and the same
performance is expected when connected to actual applications of these products.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
21
Setup
www.ti.com
5.3.3.9
Configuration ID 8: Thunderbolt Desktop/Add-in Card
Table 11. Configuration ID 8
5.3.3.9.1
Overview
The TPS65982-EVM will boot up and initialize into configuration ID 8 when the switches [B0], [B1], and
[B2] on switch bank S1 are pushed to the left-hand side and switch [B3] on switch bank S1 is pushed to
the right-hand side. Configuration ID 8 is designed to model a Thunderbolt Desktop/Add-in Card
application.
A TPS65982-EVM configured as a desktop is capable of providing (sourcing) power. The fully-featured
Type-C port can be a downstream-facing port (DFP) for DisplayPort video and Thunderbolt Alternate
Mode video+data, which is also emulated by this EVM configuration.
5.3.3.9.2
Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path and 12 V at 3 A through the PP_HV internal FET path.
5.3.3.9.3
Sink Capabilities
This configuration is capable of negotiating a PD contract to sink 5 V at 0 A.
5.3.3.9.4
Video Capabilities
This configuration is capable of negotiating a USB PD Thunderbolt Alternate Mode contract for video+data
as a downstream-facing port (DFP). This configuration is also capable of negotiating a USB PD alternate
mode contract for DisplayPort video as a downstream-facing port (DFP). An alternate mode contract will
only be negotiated successfully when connected to a product which is capable of Thunderbolt Alternate
Mode or DisplayPort video as an upstream-facing port (UFP).
5.3.3.9.5
Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 2 for providing power and
entering Thunderbolt Alternate Mode for video+data. This configuration is also compatible with a
TPS65982-EVM using configuration ID 4 for providing power and entering DisplayPort alternate mode.
22
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.10
Configuration ID 9: Desktop/Add-in Card
Table 12. Configuration ID 9
5.3.3.10.1 Overview
The TPS65982-EVM will boot up and initialize into configuration ID 9 when [B0] and [B3] DIP switches on
S1 are pushed to the right-hand side and switch [B1] and [B2] on switch bank S1 is pushed to the lefthand side. Configuration ID 9 is designed to model a desktop application.
A TPS65982-EVM configured as a desktop is capable of providing (sourcing) power. A fully-featured
Type-C port on a desktop can be capable as a downstream-facing port (DFP) for DisplayPort video, which
is also emulated by this EVM configuration.
5.3.3.10.2 Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path and 12 V at 3 A through the PP_HV internal FET path.
5.3.3.10.3 Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 0 A and 20 V at 3 A through the
PP_HV internal FET path.
5.3.3.10.4 Video Capabilities
This configuration is capable of negotiating a USB PD alternate mode contract for DisplayPort video as a
downstream-facing port (DFP). An alternate mode contract will only be negotiated successfully when
connected to a product which is capable of DisplayPort video as an upstream-facing port (UFP).
5.3.3.10.5 Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 11 for providing power and
entering DisplayPort alternate mode. This configuration is also compatible with a TPS65982-EVM using
configuration ID 4 for providing power and entering DisplayPort alternate mode
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
23
Setup
www.ti.com
5.3.3.11
Configuration ID 10: Thunderbolt Bus-Powered Device
Table 13. Configuration ID 10
5.3.3.11.1 Overview
The TPS65982-EVM will boot up and initialize into configuration ID 10 when the DIP switches [B1] and
[B3] on switch bank S1 are pushed to the right-hand side and [B0] and [B2] on switch bank S1 is pushed
to the left-hand side. Configuration ID 10 is designed to model Thunderbolt Bus Powered Device.
A TPS65982-EVM configured as a Thunderbolt device is able to enter the Thunderbolt alternate mode.
5.3.3.11.2 Source Capabilities
This configuration is not capable of providing power.
5.3.3.11.3 Sink Capabilities
This configuration is capable of negotiating a PD contract to sink 5 V at 3 A, 12 V at 1.2 A, and 20 V at
0.75 A.
5.3.3.11.4 Video Capabilities
This configuration is capable of negotiating a USB PD Thunderbolt Alternate Mode contract for
video+data.
5.3.3.11.5 Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 2 and 8 to enter the
Thunderbolt alternate mode.
24
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.12
Configuration ID 11: Mini-Docking System
Table 14. Configuration ID 11
5.3.3.12.1 Overview
The TPS65982-EVM will power-on and initialize into configuration ID 11 when [B0], [B1] and [B3] on
switch bank S1 are pushed to the right-hand side and [B2] is pushed to the left. Configuration ID 11 is
designed to model a docking system application.
A TPS65982-EVM configured as a dock is capable of providing (sourcing) power and consuming (sinking)
power. The fully-featured Type-C port of a dock which faces a laptop can be an upstream-facing port
(UFP) for DisplayPort video, which is also emulated by this EVM configuration. This configuration will also
initiate a PD power role swap to source and/or a PD data role swap to UFP.
5.3.3.12.2 Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A, and 20 V at 3 A through the
PP_EXT external FET path.
5.3.3.12.3 Sink Capabilities
This configuration is capable of negotiating PD contracts to sink 5 V at 1.5 A and 20 V at 3 A
5.3.3.12.4 Video Capabilities
This configuration is capable of negotiating a USB PD alternate mode contract for DisplayPort video as an
upstream-facing port (UFP). An alternate mode contract will only be negotiated successfully when
connected to a product which is capable of DisplayPort video as a downstream-facing port (DFP).
5.3.3.12.5 Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 1 for consuming or providing
power and entering DisplayPort alternate mode. When acting as a bus-powered dock connecting to
configuration ID 3 will power the dock from bus-power and will negotiate DisplayPort alternate mode.
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
25
Setup
www.ti.com
5.3.3.13
Configuration ID 12: Mid-Power Charger Adapter
Table 15. Configuration ID 12
5.3.3.13.1 Overview
The TPS65982-EVM will boot up and initialize into configuration ID 12 when [B0] and [B1] on switch bank
S1 is pushed to the left-hand side and [B2] and [B3] on switch bank S1 is pushed to the right-hand side.
Configuration ID 12 is designed to model a charger-adapter application.
A TPS65982-EVM configured as a charger is capable of providing (sourcing) power only. A fully-featured
Type-C port on a charger can be capable of USB 2.0 and USB3.1 data, which is also emulated by this
EVM configuration.
5.3.3.13.2 Source Capabilities
This configuration is capable of negotiating PD contracts to source 5 V at 3 A through the PP_5V0 internal
FET path, 12 V at 3 A through the PP_HV internal FET path
5.3.3.13.3 Sink Capabilities
This configuration is designed to be a provider (source) of power only, and therefore does not have any
sink capabilities.
5.3.3.13.4 Video Capabilities
This configuration is capable of USB 2.0 and USB 3.1 data only, and therefore does not have any video
capabilities.
5.3.3.13.5 Ideal Connections
This configuration pairs ideally with a TPS65982-EVM using configuration ID 7 for providing power and
enters USB2.0 and 3.1 mode for data by default. This configuration can be used with any of the other
configurations which are capable of sinking power.
26
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Setup
www.ti.com
5.3.3.14
Configuration ID 13: Type-C UFP Only
Table 16. Configuration ID 13
5.3.3.14.1 Overview
The TPS65982-EVM will boot up and initialize into configuration ID 13 when [B1] on switch bank S1 is
pushed to the left-hand side and [B0], [B2], and [B3] on switch bank S1 is pushed to the right-hand side.
Configuration ID 13 is designed to model Type-C UFP only device.
5.3.3.14.2 Source Capabilities
This configuration is capable not capable of providing power.
5.3.3.14.3 Sink Capabilities
This configuration is designed to only sink Type-C power (5 V).
5.3.3.15
Configuration ID 14: Type-C DFP Only
Table 17. Configuration ID 14
5.3.3.15.1 Overview
The TPS65982-EVM will boot up and initialize into configuration ID 14 when [B0] on switch bank S1 is
pushed to the left-hand side and [B1], [B2], and [B3] on switch bank S1 is pushed to the right-hand side.
Configuration ID 14 is designed to model Type-C DFP only device.
5.3.3.15.2 Source Capabilities
This configuration is capable of providing Type-C power (5 V at 3 A).
5.3.3.15.3 Sink Capabilities
This configuration is not capable of sinking power
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
27
Setup
www.ti.com
5.3.3.16
Configuration ID 15: Type-C DRP Only
Table 18. Configuration ID 15
5.3.3.16.1 Overview
The TPS65982-EVM will boot up and initialize into configuration ID 15 when [B0], [B1], [B2], and [B3] on
switch bank S1 are pushed to the right-hand side. Configuration ID 15 is designed to model Type-C DRP
only device.
5.3.3.16.2 Source Capabilities
This configuration is capable of providing Type-C power (5 V at 3 A).
5.3.3.16.3 Sink Capabilities
This configuration is designed to only sink Type-C power (5 V).
28
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Schematic
www.ti.com
6
Schematic
The circuit diagram in Figure 3 shows the schematic for page 1 of the TPS65982-EVM. Page 1 includes the TPS65982 IC (U2), the USB Type-C
receptacle (J1), the SPI Flash memory IC (U1), the ESD ICs (U3 and U4), the switch banks (S1 and S2), the Tiva LaunchPad receptacles (J2 and
J3), the External FETs for 5-A delivery (Q1 and Q2), the LEDs (D2–D8) and driving FETs (Q3–Q8, Q13–Q15), and necessary passive circuitry for
the TPS65982.
1
2
3
4
R1
0.01
J6
5
Back t o Bac k N FET Con figu ratio n
30V Ra ted NFET Re comm end ed
Q1
Q2
LDO _3V 3
6
C2
R4
3.3k
0 .1 µF
1 ,2,3
E xt ernal Power
C1
10µF
R2
D NP
0
R5
0
GND
R6
DNP
0
GND
6
SP I _CLK
VCC
5
2
3
7
DI /I O0
DO /I O1
WP /I O2
HO LD/I O3
CS
CLK
HV _GA TE 1
HV_GATE2
C6
1µF
S PI _M OS I
R9
3.3k
S PI _M IS O
R8
3.3k
LDO_3 V3
4
GND
S E NSE P
S E NSE N
A
1
S P I_CS Z
R7
3 .3k
U1
8
1,2,3
7 ,8 7,8
5 ,6, 5 ,6 ,
R3
0
A
W25 Q8 0D VSNIG
GND
U2 A
GN D
B4
A4
B3
A3
SP I _MO SI
SP I _MI S O
SP I _CSZ
S P I_CLK
L4
K4
J1
J2
A UX_P
AUX _N
0
TP2
RP D_G2
K 10
U2 B
C_CC2
R 11
C1 8
C 19
220pF
0
I2C_S CL2
I2C_S DA 2
I2C_I RQ2Z
HV_G ATE 1
SP I _MO SI
SP I _MI S O
SP I _SS Z
SP I _CLK
RE SE T
HV_G ATE 2
RE SE T
B 10
R 30
RPD_G2
D NP
HV_GATE2
A1
B8
D8
E5
E6
E7
E8
F5
F6
F7
F8
G5
G6
G7
G8
H4
H5
H8
L1
G ND
D6
S ys t em _RES E T
F11
C 53
0 .0 1µF
RE SE TZ
E 11
R2 6
100k
M RES E T
GND
UART_RX
UART_ TX
C_US B_T P
C_USB _TN
LSX _R2P
LSX _P 2R
C_USB _B P
C_US B _BN
C_S BU1
C_S BU2
K6
L6
C_US B_T _P
C_US B_T _N
K7
L7
C_US B_B _P
C_US B_B _N
K8
L8
PP _HV
PP _HV
PP _HV
PP _HV
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
GND
P P _5V 0
P P _5V 0
P P _5V 0
P P _5V 0
VB US
21 ohm
C7
0.01 µF
A8
A7
A6
B7
C4
10µF
C5
0 .1 µF
A 11
B 11
C11
D11
C11
22µF
C 12
0 .1 µF
C8
0 .0 1µF
C9
0.01 µF
HV _S ourc e
GND
H5
H6
S y stem _5V
GND
V DDIO
S ys tem _3V 3
H2
LDO_3V 3
L DO_3V 3
K1
LDO_1V 8A
A2
L DO_1V 8D
C1 3
1µF
C1 4
10µF
C17
1µF
C16
1µF
Ti va _3V3
V OUT _3V 3
UA RT_T X
UART _RX
AUX _P
A UX_ N
S PI _CLK
I2C_I RQ1Z
I 2C_SCL 1
I 2C_S DA 1
V OUT _3V 3
G1
DEB UG3
DEB UG4
NC
De ad Ba tte ry & I2C Ad dr ess
Co nfig ura ti on Sw itch (DN P)
GND
1
2
3
4
DEB UG_CT L1
DEBUG_CTL2
B US PO WERZ
R4 9
R52
R55
S1
DN P
R4 2
R4 3
R4 4
R4 5
8
7
6
5
1 .0 0k
1 .0 0k
1 .0 0k
1 .0 0k
1
2
3
4
LDO _3V 3
G PI O1
DE B UG_3
DEBUG_4
LDO _1V 8D GP IO5 _HPD
100k
100k
100k
R21
R25
R29
R33
GND
R 12
R 13
R 14
R 15
8
7
6
5
100k
100k
100k
100k
1.00 k
1.00 k
1.00 k
1.00 k
LDO_3V 3
GND
I2C_SCL2
I2C_SDA2
I2C_IRQ2Z
I2C_I RQ1Z
I 2C_S CL1
I2C_S DA 1
I 2C_IRQ2 Z
I 2C_SDA 2
I 2C_SCL2
GP I O7
GPIO0
GPIO1
S WD_DATA
1
3
5
7
9
11
13
15
17
19
R 75
3 .83 k
R 76
R 78
9 .09 k
R 79
DNP DN PR4 8
DNP DN PR5 1
DNP DN PR5 4
DNP DN PR5 8
0
R6 0
0
R6 2
DNP DN PR6 4
0
R6 6
DNP DN PR6 8
LS X _P2 R
M RES E T
RE SE T Z
GP I O6
S P I_M OS I
S P I_M IS O
DE B UG_2
SPI_CSZ
US B 2_RP_N
C
3.83 k
R8 0
3 .8 3k
USB 2.0 Top /Bo ttom
ESD P rotectio n
U3
D1+
D1-
D2+
D2-
2
DE B UG_1
Q1 0
1
C_SB U_P
C_S B U_N
C_CC1
C_CC2
6
7
9
10
NC
NC
NC
NC
4
5
GND
GND
8
3
TPD4 E05 U06 DQA
Nu mbe r: H VL11 7
R ev: D
Te xas I nstrume nts an d/or its li cen sors do not wa rran t the accur acy or co mpl eten ess of th is sp ecifi cation or an y inform ation con ta in ed the rei n. Te xas I nstrume nts an d/or its li cen sors do not SVN Re v: N ot in versi on contro l
w arra nt th at th is de sig n wi ll mee t the spe cifica ti ons, wi ll be suita ble fo r yo ur a ppl ica ti on or fit f or an y particu la r purp ose , or will o pe rate in an i mple men tation . Te x as I nstrume nts an d/or its
Dra wn By:
l ice nso rs do no t warra nt th at th e de sig n is pro du ction worth y. You sho ul d comp le te ly valida te an d t est yo ur d esi gn im ple men tation to confir m the system f uncti ona li ty f or you r app li catio n.
Eng in ee r: Jaco b O ntive ros
3
GND
C_S BU_N
C_S BU_P
C_USB _B _N
C_US B_B _P
1
2
D1+
D1-
D2+
D2-
NC
NC
NC
NC
GND
GND
4
5
C_USB _T _N
C_US B_T _P
3
1
2
G ND
2
LDO_3V 3
LDO_3V3
C_US B _T_P
C_US B_T _N
C_US B_B _P
C_USB _B _N
6
7
9
10
4
5
8
3
D
TPD4E 05U 06 DQA
GND
1
R 20
3 .83k
R24
3.83 k
R7 7
9 .0 9k
U4
C_CC2
C_CC1
2
Q9
1
GND
GND
2
4
6
8
10
12
14
16
18
20
CC1 /CC2 & SBU 1/SBU2
ES D Protectio n
R9 6
560
3
3
GPIO3
Tiv a_5V
DNP
R1 6
DN P
DNP
R1 7
DN P
DNP
R3 2
DN P
DNP
R3 6
DNP DN PR3 5
DNP DN PR3 7
DN P
0
R39
0
R4 1
I2C Pu ll- Ups f or I 2C 1 & I2 C2
2
2
2
D9
White
R90
560
Q8
1
2
GPIO6
1
1
1
1
2
3
Q7
1
D8
White
R 89
560
2
GPIO2
2
GPIO8
2
GP I O0
Q6
1
D7
Wh ite
R 87
560
3
3
R8 6
560
Q5
1
D6
Wh ite
2
2
2
3
DE BUG _2
Q4
1
D5
Whi te
R7 4
560
2
GP IO 7
Q3
2
D
D4
Whi te
R73
560
3
R 72
560
1
1
1
1
1
2
D3
White
0
R 46
DNP DN PR 47
DN P DN PR 50
DNP DN PR 53
DN P DN PR 57
DNP
R 59
DN P
DNP
R 61
P
DNP DN
DN PR 63
DNP
R 65
DNP DN PR 67
LS X _R2P
GP I O5_HP D
GPIO3
GP IO 2
GPIO8
DE BUG _1
DEBUG_4
DEBUG_3
USB 2_RP _P
S y st em _5V
D2
White
B
GND
J3
R70 GP I O4_HP D
PD & A ltern ate Mo de
Con figu ratio n Swi tc h
S2
L11
H1
H2
S WD_CLK
100k
TPS659 82 ABZQZR
1
3
5
7
9
11
13
15
17
19
100k
GND
C3 0 .22µF
DN P DN PR 18
DNP
R 19
DN P
DNP
R 23
DN P
DN P
R 31
DN P
DNP DN PR 34
0
R 38
0
R40
0
R69
0
R71
2
4
6
8
10
12
14
16
18
20
L DO _1V 8D
GND
H7
VBUS
C_S B U_N
C_US B _B _N
C_US B _B _P
C_CC2
VBUS
20-0 00 00 16- 01
GND
H1
VI N_3V 3
V OUT _3V 3
H1
H2
GND
B 12
B 11
B 10
B9
B8
B7
B6
B5
B4
B3
B2
B1
J2
G ND
B1
H5
H6
TP4
H4
H3
G ND
G ND
SS
C1 0
0.0 1µF
H10
P P _CAB LE
TPS65 982 ABZQZR
C_S BU_P
C_S BU_N
VBUS
C_CC1
C_US B_T _P
C_USB _T_N
C_S B U_P
V B US
L1
H11
J10
J11
K 11
VB US
VB US
VB US
VB US
BUS P OWERZ
DNP
HV _GAT E 1
A9
LDO_B MC
R 22 D NP DNP
RPD_G1
S ENS E N
B9
E1
F10
GND
S ENS E P
A 10
1µF
B US PO WERZ
TP3
G ND
RX1+
RX 1VB US
S B U2
DD+
CC2
VB US
TX 2T X2+
G ND
3
D1
R 10
L10
H4
H3
GND
T X1+
T X1V B US
CC1
D+
DS B U1
V B US
RX 2RX 2+
GND
2
G ND
RPD_G1
K9
H7
H8
A1
A2
A3
A4
A5
A6
A7
A8
A9
A 10
A 11
A 12
1
GND
1
SE NS EN
DEB UG1
DEB UG2
L3
K3
DEBUG_3
DEBUG_4
C
TP1
USB _RP _P
USB _RP _N
L2
K2
DE BUG _1
DEBUG_2
C_CC1
G ND
S ENS E P
AUX _P
AUX _N
L5
K5
US B 2_RP _P
US B2_RP _N
L9
GND
DEB UG_CT L1
DEB UG_CT L2
F2
E2
LSX _R2P
LSX_P2R
C_CC2
RP D_G2
C15
220pF
SW D_ DATA
SW D_ CLK
E4
D5
UA RT_RX
UART _TX
RP D_G1
M RE SE T
F4
G4
S WD_DATA
S WD_CLK
DEB UG_CT L1
DEBUG_CTL2
C_CC1
I2C_S CL1
I2C_S DA 1
I2C_I RQ1Z
B5
A5
B6
I2C_SCL2
I2C_SDA2
I2C_IRQ2Z
B
GP IO0
GP IO1
GP IO2
GP IO3
GP IO4_ HPD
GP IO5_ HPD
GP IO6
GP IO7
GP IO8
D2
D1
C1
I 2C_S CL1
I2C_S DA 1
I2C_ IRQ1Z
J1
H7
H8
GND
I2C_A DDR
B2
C2
D10
G11
C10
E 10
G10
D7
H6
GP I O0
GPIO1
GPIO2
GPIO3
G PI O4_HP D
GPIO5_HPD
GPIO6
GPIO7
GPIO8
GND
R_OS C
F1
2
0
3
R2 8 15.0k G2
R5 6
GND
GND
Des ign ed fo r:Pu bl ic Re lea se
Mod. Da te: 6 /15/2 015
Proje ct Title: TPS65 98 2EVM
She et Title : TPS6 59 82_ Ty pe C_ PD
Assemb ly Va rian t: -0 01
She et: 2 of 4
Fi le: HVL 117 D_ Pow er_ De live ry.Sch D oc
S ize: B
Con tact: j-o ntive ros@ ti .co m
h ttp ://ww w.ti.co m
© Texas Ins trument s 2015
6
Figure 3. TPS65982-EVM Schematic Page 1
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
TPS65982 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
29
Schematic
www.ti.com
The circuit diagram in Figure 4 shows the schematic for page 2 of the TPS65982-EVM. Page 2 includes power path-related ICs: the
External_Power to System_3V3 buck converter (U5) and passive components, the External_Power to System_5V buck converter (U6) and passive
components, the External_Power to HV_Source buck converter (U7) and passive components, the Barrel Jack receptacle (J4), the power rail
header (J5), the Tiva to System power jumper (J7), and the System_RESET push-button (S3).
1
2
3
4
5
6
U5
C2 0
1
Ex t ernal Power
C22
10µF
A
C 23
R8 1
0 .1µF D NP
DNP
VI N
B OOT
L2
9
J9
0.1µF
3V3_VSENSE
GND
6
8
R8 3
D NP
DNP
10
VS E NSE
PH
COM P
EN
RT
G ND
G ND
GND
P AD
A
2
Sy ste m_3V 3
C24
22µF
10uH
7
3
4
5
11
C25
22µF
C 26
0 .1µF
R82 DN PC2 7
100k
DN P
J4
E xt ernal Po wer
3V 3_V S ENS E
G ND
R 85
2 .74k
2
R 84
32.4k
TPS54 335 D RCR
S ENS E
3
P OWE R
C28
330pF
G ND
GND
R 88 D NPC3 0
47.5k
DNP
C29
5600pF
SHIELD
SHIELD
SHIELD
S HIE LD
P OWE R
1
GND
GND
GND
9
8
7
6
5
4
JPD 113 5 -50 9-7 F
G ND
GND
GND
J5
3
S yst em _3V 3
S yst em _5V
HV _S ource
DNP2
1
U6
B
B
C3 1
1
External Power
C 33
10µF
VI N
B OOT
L3
9
0.1µF
C 34
R9 1
0 .1µF D NP
DNP
5V_VSENSE
GND
6
8
R9 3
D NP
DNP
10
VS E NSE
PH
COM P
EN
RT
G ND
G ND
GND
P AD
2
Sy ste m_5V
C 35
22µF
10uH
7
C36
22µF
C 37
0 .1µF
R92 DN PC3 8
100k
DN P
TP5
G ND
3
4
5
11
5V _V S ENS E
G ND
R 95
8 .45k
R 94
19.1k
S3
TPS54 335 D RCR
R 27
C39
100pF
G ND
GND
R 97 D NPC4 1
47.5k
DNP
Sy stem _RE S ET
C40
2200pF
1 .00k
S ys t em _3V3
GND
GND
J7
GND
1
3
S y st em _5V
S yst em _3V 3
DNP
2
4
Tiv a_5V
Tiv a_3V 3
C
C
U7
C4 2
1
External Power
C44
10µF
C 45
R1 01
0 .1µF D NP
DNP
12V_VSENSE
R1 03
D NP
DNP
B OOT
L4
9
0.1µF
6
8
GND
VI N
10
VS E NSE
PH
COM P
EN
RT
G ND
G ND
GND
P AD
2
HV_S ourc e
10uH
7
C 46
22µF
3
4
5
11
G ND
R 10 8
9 .53k
C47
22µF
C 48
0 .1µF
R102DN PC4 9
100k
DN P
12V _V S ENS E
R 104
7 .1 5k
TPS54 335 D RCR
C50
91pF
G ND
GND
R 10 9 D NPC5 2
47.5k
DNP
C51
1800pF
GND
GND
D
D
GND
Nu mbe r: H VL11 7
R ev: D
Te xas I nstrume nts an d/or its li cen sors do not wa rran t the accur acy or co mpl eten ess of th is sp ecifi cation or an y inform ation con ta in ed the rei n. Te xas I nstrume nts an d/or its li cen sors do not SVN Re v: N ot in versi on contro l
w arra nt th at th is de sig n wi ll mee t the spe cifica ti ons, wi ll be suita ble fo r yo ur a ppl ica ti on or fit f or an y particu la r purp ose , or will o pe rate in an i mple men tation . Te x as I nstrume nts an d/or its
Dra wn By:
l ice nso rs do no t warra nt th at th e de sig n is pro du ction worth y. You sho ul d comp le te ly valida te an d t est yo ur d esi gn im ple men tation to confir m the system f uncti ona li ty f or you r app li catio n.
Eng in ee r: Jaco b O ntive ros
1
2
3
4
5
Des ign ed fo r:Pu bl ic Re lea se
Proje ct Title: TPS65 98 2EVM
She et Title : P owe r Path Sup plies
Assemb ly Va rian t: -0 01
Fi le: HVL 117 D_ Pow er_ Path.Sch Do c
Con tact: j-o ntive ros@ ti .co m
Mod. Da te: 6 /19/2 015
She et: 3 of 4
S ize: B
h ttp ://ww w.ti.co m
© Texas Ins trument s 2015
6
Figure 4. TPS65982-EVM Schematic Page 2
30
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Board Layout
www.ti.com
7
Board Layout
Figure 5 through Figure 12 illustrate the PCB layouts of this EVM.
Figure 5. PCB Layer 1 (Top Layer)
Figure 6. PCB Layer 1 (Component View)
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
31
Board Layout
www.ti.com
Figure 7. PCB Layer 2 (GND Plane)
Figure 8. PCB Layer 3 (Inner Signal Layer 1)
32
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Board Layout
www.ti.com
Figure 9. PCB Layer 4 (GND Plane)
Figure 10. PCB Layer 5 (Inner Signal Layer 2)
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
33
Board Layout
www.ti.com
Figure 11. PCB Layer 6 (Bottom Layer)
Figure 12. PCB Layer 6 (Component View)
34
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Bill of Materials
www.ti.com
8
Bill of Materials
Table 19 lists the EVM BOM.
Table 19. Bill of Materials
Item #
Designator
Quantit
y
Value
PartNumber
Manufacturer
Description
1
!PCB1
1
2
C1, C4
2
10uF
3
C2, C12
2
4
C3
5
HVL117D
Any
Printed Circuit Board
GRM188R61E106MA73
MuRata
CAP, CERM, 10 µF, 25 V, +/- 20%, X5R, 0603
0603
0.1uF
CL03A104KP3NNNC
Samsung
CAP, CERM, 0.1 µF, 10 V, +/- 10%, X5R, 0201
0201
1
0.22uF
GRM033R60J224ME90
MuRata
CAP, CERM, 0.22 µF, 6.3 V, +/- 20%, X5R, 0201
0201
C5
1
0.1uF
C1005X7R1H104M
TDK
CAP, CERM, 0.1 µF, 50 V, +/- 20%, C0G/NP0, 0402
0402
6
C6
1
1uF
C1005JB1V105K050BC
TDK
CAP, CERM, 1 µF, 35 V, +/- 10%, JB, 0402
0402
7
C7, C8, C9, C10
4
0.01uF
GRM155R71H103KA88D
MuRata
CAP, CERM, 0.01 µF, 50 V, +/- 10%, X7R, 0402
0402
8
C11
1
22uF
GRM188R61A226ME15D
MuRata
CAP, CERM, 22 µF, 10 V, +/- 20%, X5R, 0603
0603
9
C13, C16, C17, C18
4
1uF
CL03A105MP3NSNC
Samsung
CAP, CERM, 1 µF, 10 V, +/- 20%, X5R, 0201
0201
10
C14
1
10uF
CL05A106MP5NUNC
Samsung
CAP, CERM, 10 µF, 10 V, +/- 20%, X5R, 0402
0402
11
C15, C19
2
220pF
GRM033R71E221KA01D
MuRata
CAP, CERM, 220 pF, 25 V, +/- 10%, X7R, 0201
0201
12
C20, C23, C26, C31,
C34, C37, C42, C45,
C48
9
0.1uF
C1005X7R1H104M
TDK
CAP, CERM, 0.1uF, 50V, +/-20%, C0G/NP0, 0402
0402
13
C22, C33, C44
3
10uF
C2012X5R1E106K125AB
TDK
CAP, CERM, 10 µF, 25 V, +/- 10%, X5R, 0805
0805
14
C24, C25, C35, C36,
C46, C47
6
22uF
C2012X5R1V226M125AC
TDK
CAP, CERM, 22 µF, 35 V, +/- 20%, X5R, 0805
0805
15
C28
1
330pF
C1005C0G1H331J
TDK
CAP, CERM, 330 pF, 50 V, +/- 5%, C0G/NP0, 0402
0402
16
C29
1
5600pF
GRM155R71H562KA88D
MuRata
CAP, CERM, 5600 pF, 50 V, +/- 10%, X7R, 0402
0402
17
C39
1
100pF
CC0402KRX7R9BB101
Yageo America
CAP, CERM, 100 pF, 50 V, +/- 10%, X7R, 0402
0402
18
C40
1
2200pF
GRM155R61H222KA01D
MuRata
CAP, CERM, 2200 pF, 50 V, +/- 10%, X5R, 0402
0402
19
C50
1
91pF
GRM1555C1H910JA01D
MuRata
CAP, CERM, 91 pF, 50 V, +/- 5%, C0G/NP0, 0402
0402
20
C51
1
1800pF
GRM155R71H182KA01D
MuRata
CAP, CERM, 1800 pF, 50 V, +/- 10%, X7R, 0402
0402
21
C53
1
0.01uF
GRM033R61A103KA01D
MuRata
CAP, CERM, 0.01 µF, 10 V, +/- 10%, X5R, 0201
0201
22
D2, D3, D4, D5, D6,
D7, D8, D9
8
White
LW QH8G-Q2S2-3K5L-1
OSRAM
LED, White, SMD
0402, White
23
J1
1
20-0000016-01
Lintes Technology
Connector, Receptacle, USB Type C, R/A, SMT
Connector, Receptacle, USB
Type C, SMT
24
J2, J3
2
PPPC102LFBN-RC
Sullins Connector Solutions
Receptacle, 100mil, 10x2, Gold, TH
10x2 Receptacle
25
J4
1
JPD1135-509-7F
Foxconn
Connector, DC Power Jack, R/A, 3 Pos, TH
Power connector
26
J6
1
90120-0122
Molex
Header, 100mil, 2x1, Tin, TH
Header 2x1
27
L1
1
FBMJ2125HM210NT
Taiyo Yuden
Ferrite Bead, 21 ohm @ 100MHz, 6A, 0805
0805
28
L2, L3, L4
3
ASPI-0630LR-100M-T15
ABRACON
29
Q1, Q2
2
30V
CSD17309Q3
Texas Instruments
MOSFET, N-CH, 30 V, 60 A, SON 3.3x3.3mm
SON 3.3x3.3mm
30
Q3, Q4, Q5, Q6, Q7,
Q8, Q9, Q10
8
50 V
DTC114EUAT106
Rohm
Transistor, NPN, 50 V, 0.05 A, SOT-323
SOT-323
31
R1
1
0.01
WSL0805R0100FEA18
Vishay-Dale
RES, 0.01 ohm, 1%, 0.25W, 0805
0805
21 ohm
PackageReference
7.2 mm x 6.65 mm
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
TPS65982 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
35
Bill of Materials
www.ti.com
Table 19. Bill of Materials (continued)
Item #
Designator
Quantit
y
Value
PartNumber
Manufacturer
Description
PackageReference
32
R3, R5, R10, R11,
R22, R30, R38, R39,
R40, R41, R46, R56,
R60, R62, R65, R66,
R69, R71
18
0
ERJ-1GE0R00C
Panasonic
RES, 0, 5%, 0.05 W, 0201
0201
33
R4, R7, R8, R9
4
3.3k
CRCW04023K30JNED
Vishay-Dale
RES, 3.3 k, 5%, 0.063 W, 0402
0402
34
R12, R13, R14, R15,
R27, R42, R43, R44,
R45
9
1.00k
CRCW02011K00FKED
Vishay-Dale
RES, 1.00 k, 1%, 0.05 W, 0201
0201
35
R20, R75, R76, R79,
R80
5
3.83k
CRCW02013K83FKED
Vishay-Dale
RES, 3.83 k, 1%, 0.05 W, 0201
0201
36
R21, R24, R25, R26,
R29, R33, R49, R52,
R55, R70
10
100k
CRCW0201100KFKED
Vishay-Dale
RES, 100 k, 1%, 0.05 W, 0201
0201
37
R28
1
15.0k
CRCW040215K0FKED
Vishay-Dale
RES, 15.0 k, 1%, 0.063 W, 0402
0402
38
R72, R73, R74, R86,
R87, R89, R90, R96
8
560
CRCW0402560RJNED
Vishay-Dale
RES, 560, 5%, 0.063 W, 0402
0402
39
R77, R78
2
9.09k
CRCW02019K09FKED
Vishay-Dale
RES, 9.09 k, 1%, 0.05 W, 0201
0201
40
R82, R92, R102
3
100k
CRCW0402100KFKED
Vishay-Dale
RES, 100 k, 1%, 0.063 W, 0402
0402
41
R84
1
32.4k
CRCW040232K4FKED
Vishay-Dale
RES, 32.4 k, 1%, 0.063 W, 0402
0402
42
R85
1
2.74k
CRCW04022K74FKED
Vishay-Dale
RES, 2.74 k, 1%, 0.063 W, 0402
0402
43
R88, R97, R109
3
47.5k
CRCW040247K5FKED
Vishay-Dale
RES, 47.5 k, 1%, 0.063 W, 0402
0402
44
R94
1
19.1k
CRCW040219K1FKED
Vishay-Dale
RES, 19.1 k, 1%, 0.063 W, 0402
0402
45
R95
1
8.45k
CRCW04028K45FKED
Vishay-Dale
RES, 8.45 k, 1%, 0.063 W, 0402
0402
46
R104
1
7.15k
CRCW04027K15FKED
Vishay-Dale
RES, 7.15 k, 1%, 0.063 W, 0402
0402
47
R108
1
9.53k
CRCW04029K53FKED
Vishay-Dale
RES, 9.53 k, 1%, 0.063 W, 0402
0402
48
S1
1
TDA04H0SB1
C&K Components
DIP Switch, SPST 4Pos, Slide, SMT
6.2x2.0x6.2mm
49
S3
1
B3U-1000P
Omron Electronic Components
SWITCH TACTILE SPST-NO 0.05A 12V
3x1.6x2.5mm
50
TP1, TP2, TP3, TP4,
TP5
5
5019
Keystone
Test Point, Miniature, SMT
Test Point, Miniature, SMT
51
U1
1
W25Q80DVSNIG
Winbond
3V, 8Mbit, Serial Flash Memory with Dual and Qual SPI, SOIC-8
SOIC-8
52
U2
1
TPS65982ABZQZR
Texas Instruments
TPS65982 Preview Specification, ZQZ0096A
ZQZ0096A
53
U3, U4
2
TPD4E05U06DQA
Texas Instruments
1, 4, 6 CHANNEL PROTECTION SOLUTION FOR SUPER-SPEED (UP TO 6 GBPS)
INTERFACE, DQA0010A
DQA0010A
54
U5, U6, U7
3
TPS54335DRCR
Texas Instruments
4.5V to 28V Input, 3A Output, Synchronous SWIFT Step-Down DC-DC Converter,
DRC0010J
DRC0010J
55
C27, C30, C38, C41,
C49, C52
0
120pF
GRM1555C1H121JA01D
MuRata
CAP, CERM, 120 pF, 50 V, +/- 5%, C0G/NP0, 0402
0402
56
D1
0
40V
B340A-13-F
Diodes Inc.
Diode, Schottky, 40 V, 3 A, SMA
SMA
57
FID1, FID2, FID3,
FID4, FID5, FID6
0
N/A
N/A
Fiducial mark. There is nothing to buy or mount.
Fiducial
58
H1, H2, H3, H4
0
NY PMS 440 0025 PH
B&F Fastener Supply
Machine Screw, Round, #4-40 x 1/4, Nylon, Philips panhead
Screw
59
H5, H6, H7, H8
0
1902C
Keystone
Standoff, Hex, 0.5"L #4-40 Nylon
Standoff
60
J5
0
PPPC031LFBN-RC
Sullins Connector Solutions
Receptacle, 100mil, 3x1, Gold, TH
Receptacle, 3x1, 2.54mm, TH
61
J7
0
15-91-2040
Molex
Header, 100mil, 2x2, Tin, SMT
2x2 100mil Tin Header
36
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Bill of Materials
www.ti.com
Table 19. Bill of Materials (continued)
Item #
Designator
Quantit
y
Value
PartNumber
Manufacturer
Description
PackageReference
62
J9
0
63
R6, R16, R17, R18,
R19, R23, R31, R32,
R34, R35, R36, R37,
R47, R48, R50, R51,
R53, R54, R57, R58,
R59, R61, R63, R64,
R67, R68
0
0
1040
Keystone
TEST POINT SLOTTED .118", TH
Test point, TH Slot Test point
ERJ-1GE0R00C
Panasonic
RES, 0, 5%, 0.05 W, 0201
0201
64
R81, R91, R101
0
65
R83, R93, R103
0
220k
CRCW0402220KJNED
Vishay-Dale
RES, 220 k, 5%, 0.063 W, 0402
0402
43.2k
CRCW040243K2FKED
Vishay-Dale
RES, 43.2 k, 1%, 0.063 W, 0402
66
S2
0
0402
TDA04H0SB1
C&K Components
DIP Switch, SPST 4Pos, Slide, SMT
6.2x2.0x6.2mm
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
TPS65982 Evaluation Module
Copyright © 2015, Texas Instruments Incorporated
37
Firmware Installation
9
www.ti.com
Firmware Installation
The following procedure is intended to describe how to flash the WQ2580 IC of the TPS65982-EVM with
firmware (1024kB .bin file) using an Aardvark SPI programmer by connecting to the SPI pins of header J2.
The following material needed to flash the TPS65982-EVM:
• TPS65982-EVM
• Aardvark SPI Programmer with accompanying USB cable
• Dell power adapter
• 1024kB .bin FW file, example “TPS65982-EVM_Flash-Image_RTM.bin”
9.1
Writing a Flash Image Using an Aardvark SPI Programmer
In the following seven steps there are images indicating additional information. Please use the legend in
Figure 13 to understand what image corresponds to what action.
Figure 13. Legend
38
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Firmware Installation
www.ti.com
9.2
Wire Aardvark to SPI Pins for Flash on the TPS65982-EVM board
Wire the Aardvark SPI pins to the corresponding SPI pins on the TPS65982-EVM J2 and J3 headers as
shown in Figure 14.
NOTE: Once wire connections are made, connect the Dell Power Adapter (Barrel Jack AC Adapter)
to the TPS65982-EVM to power up the board.
Figure 14. Aardvark Wired to SPI Pins
9.3
Run “Flash Center”.exe
Connect the Dell Power Adapter to the TPS65982-EVM and connect the Aardvark USB cable to your
computer. Next, boot up the Flash Center software (Figure 15) from the directory location you previously
installed it.
Figure 15. Flash Center GUI
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
39
Firmware Installation
9.4
www.ti.com
Add Adapter
The Flash Center application uses a variety of adapters, in order to use the Aardvark adapter it must be
added. To add, click “Add Adapters” (Figure 16) and select the Aardvark adapter when it appears as
shown in Figure 17.
Figure 16. Add Adapters... Button
Figure 17. Add Adapters Selection
NOTE: It should automatically detect the Aardvark when adding the adapter; if however, it does not
download the Aardvark drivers from Total Phase and follow the installation prompts.
Figure 18. Adapter Detection
40
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Firmware Installation
www.ti.com
9.5
Choose Target (Device Type)
In order for the Flash Center to flash the TPS65982-EVM, the proper Flash or Device type must be
selected. Click the “Choose Target” button to select the Target Device type in this case: SPI Flash →
Winbond/NexFlash → W25Q80 as shown in Figure 19.
Figure 19. Select Target Device
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
41
Firmware Installation
9.6
www.ti.com
Load Binary File
To load the binary file that will go onto the TPS65982-EVM, select load file and proceed to the directory
where the binary file has been saved. After the binary file is selected, click 'Open'. If successful, the data
section of the Flash Center should be full of values. See the screen shots in Figure 20 for examples.
Figure 20. Loading Data Section of Flash Center
42
TPS65982 Evaluation Module
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Firmware Installation
www.ti.com
9.7
Program TPS65982-EVM
To program the TPS65982-EVM, select the Program button, wait approximately 2 minutes and the write
should complete. To confirm that the TPS65982-EVM board has been programmed, either press S3 or
unplug and re-plug the Dell Power Adapter. If it has been programmed then LED B (D5) will be on.
NOTE: If an error occurs, either the board is not being powered or the SPI pins are not connected
properly.
Figure 21. Programming the TPS65982-EVM
9.8
Verify (Optional)
To confirm if the loaded binary image matches the firmware installed on the TPS65982-EVM, click the
verify button and see if it reports a success.
Figure 22. Verifying Binary Image
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
TPS65982 Evaluation Module
43
Revision History
www.ti.com
Revision History
Changes from B Revision (August 2015) to C Revision ................................................................................................ Page
•
•
Added Using the TPS65986 on the TPS65982-EVM section. ...................................................................... 5
Changed TPS65982-EVM Configuration Table Overview section, added many new subsections. .......................... 13
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Revision History
Changes from A Revision (June 2015) to B Revision .................................................................................................... Page
•
Changed BOM to EVM Rev. D. ........................................................................................................ 35
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Revision History
Changes from Original (June 2015) to A Revision ......................................................................................................... Page
•
•
Changed format to standard EVM UG template....................................................................................... 1
Added Firmware Installation section. .................................................................................................. 38
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
44
Revision History
SLVUAF8C – June 2015 – Revised November 2015
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
STANDARD TERMS AND CONDITIONS FOR EVALUATION MODULES
1.
Delivery: TI delivers TI evaluation boards, kits, or modules, including any accompanying demonstration software, components, or
documentation (collectively, an “EVM” or “EVMs”) to the User (“User”) in accordance with the terms and conditions set forth herein.
Acceptance of the EVM is expressly subject to the following terms and conditions.
1.1 EVMs are intended solely for product or software developers for use in a research and development setting to facilitate feasibility
evaluation, experimentation, or scientific analysis of TI semiconductors products. EVMs have no direct function and are not
finished products. EVMs shall not be directly or indirectly assembled as a part or subassembly in any finished product. For
clarification, any software or software tools provided with the EVM (“Software”) shall not be subject to the terms and conditions
set forth herein but rather shall be subject to the applicable terms and conditions that accompany such Software
1.2 EVMs are not intended for consumer or household use. EVMs may not be sold, sublicensed, leased, rented, loaned, assigned,
or otherwise distributed for commercial purposes by Users, in whole or in part, or used in any finished product or production
system.
2
Limited Warranty and Related Remedies/Disclaimers:
2.1 These terms and conditions do not apply to Software. The warranty, if any, for Software is covered in the applicable Software
License Agreement.
2.2 TI warrants that the TI EVM will conform to TI's published specifications for ninety (90) days after the date TI delivers such EVM
to User. Notwithstanding the foregoing, TI shall not be liable for any defects that are caused by neglect, misuse or mistreatment
by an entity other than TI, including improper installation or testing, or for any EVMs that have been altered or modified in any
way by an entity other than TI. Moreover, TI shall not be liable for any defects that result from User's design, specifications or
instructions for such EVMs. Testing and other quality control techniques are used to the extent TI deems necessary or as
mandated by government requirements. TI does not test all parameters of each EVM.
2.3 If any EVM fails to conform to the warranty set forth above, TI's sole liability shall be at its option to repair or replace such EVM,
or credit User's account for such EVM. TI's liability under this warranty shall be limited to EVMs that are returned during the
warranty period to the address designated by TI and that are determined by TI not to conform to such warranty. If TI elects to
repair or replace such EVM, TI shall have a reasonable time to repair such EVM or provide replacements. Repaired EVMs shall
be warranted for the remainder of the original warranty period. Replaced EVMs shall be warranted for a new full ninety (90) day
warranty period.
3
Regulatory Notices:
3.1 United States
3.1.1
Notice applicable to EVMs not FCC-Approved:
This kit is designed to allow product developers to evaluate electronic components, circuitry, or software associated with the kit
to determine whether to incorporate such items in a finished product and software developers to write software applications for
use with the end product. This kit is not a finished product and when assembled may not be resold or otherwise marketed unless
all required FCC equipment authorizations are first obtained. Operation is subject to the condition that this product not cause
harmful interference to licensed radio stations and that this product accept harmful interference. Unless the assembled kit is
designed to operate under part 15, part 18 or part 95 of this chapter, the operator of the kit must operate under the authority of
an FCC license holder or must secure an experimental authorization under part 5 of this chapter.
3.1.2
For EVMs annotated as FCC – FEDERAL COMMUNICATIONS COMMISSION Part 15 Compliant:
CAUTION
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not
cause harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to
operate the equipment.
FCC Interference Statement for Class A EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not
installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to
correct the interference at his own expense.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
FCC Interference Statement for Class B EVM devices
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of
the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference
will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which
can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more
of the following measures:
•
•
•
•
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.
3.2 Canada
3.2.1
For EVMs issued with an Industry Canada Certificate of Conformance to RSS-210
Concerning EVMs Including Radio Transmitters:
This device complies with Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:
(1) this device may not cause interference, and (2) this device must accept any interference, including interference that may
cause undesired operation of the device.
Concernant les EVMs avec appareils radio:
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio exempts de licence. L'exploitation
est autorisée aux deux conditions suivantes: (1) l'appareil ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit
accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Concerning EVMs Including Detachable Antennas:
Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada. To reduce potential radio interference to other users, the antenna type
and its gain should be so chosen that the equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for
successful communication. This radio transmitter has been approved by Industry Canada to operate with the antenna types
listed in the user guide with the maximum permissible gain and required antenna impedance for each antenna type indicated.
Antenna types not included in this list, having a gain greater than the maximum gain indicated for that type, are strictly prohibited
for use with this device.
Concernant les EVMs avec antennes détachables
Conformément à la réglementation d'Industrie Canada, le présent émetteur radio peut fonctionner avec une antenne d'un type et
d'un gain maximal (ou inférieur) approuvé pour l'émetteur par Industrie Canada. Dans le but de réduire les risques de brouillage
radioélectrique à l'intention des autres utilisateurs, il faut choisir le type d'antenne et son gain de sorte que la puissance isotrope
rayonnée équivalente (p.i.r.e.) ne dépasse pas l'intensité nécessaire à l'établissement d'une communication satisfaisante. Le
présent émetteur radio a été approuvé par Industrie Canada pour fonctionner avec les types d'antenne énumérés dans le
manuel d’usage et ayant un gain admissible maximal et l'impédance requise pour chaque type d'antenne. Les types d'antenne
non inclus dans cette liste, ou dont le gain est supérieur au gain maximal indiqué, sont strictement interdits pour l'exploitation de
l'émetteur
3.3 Japan
3.3.1
Notice for EVMs delivered in Japan: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page 日本国内に
輸入される評価用キット、ボードについては、次のところをご覧ください。
http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_01.page
3.3.2
Notice for Users of EVMs Considered “Radio Frequency Products” in Japan: EVMs entering Japan may not be certified
by TI as conforming to Technical Regulations of Radio Law of Japan.
If User uses EVMs in Japan, not certified to Technical Regulations of Radio Law of Japan, User is required by Radio Law of
Japan to follow the instructions below with respect to EVMs:
1.
2.
3.
Use EVMs in a shielded room or any other test facility as defined in the notification #173 issued by Ministry of Internal
Affairs and Communications on March 28, 2006, based on Sub-section 1.1 of Article 6 of the Ministry’s Rule for
Enforcement of Radio Law of Japan,
Use EVMs only after User obtains the license of Test Radio Station as provided in Radio Law of Japan with respect to
EVMs, or
Use of EVMs only after User obtains the Technical Regulations Conformity Certification as provided in Radio Law of Japan
with respect to EVMs. Also, do not transfer EVMs, unless User gives the same notice above to the transferee. Please note
that if User does not follow the instructions above, User will be subject to penalties of Radio Law of Japan.
SPACER
SPACER
SPACER
SPACER
SPACER
【無線電波を送信する製品の開発キットをお使いになる際の注意事項】 開発キットの中には技術基準適合証明を受けて
いないものがあります。 技術適合証明を受けていないもののご使用に際しては、電波法遵守のため、以下のいずれかの
措置を取っていただく必要がありますのでご注意ください。
1.
2.
3.
電波法施行規則第6条第1項第1号に基づく平成18年3月28日総務省告示第173号で定められた電波暗室等の試験設備でご使用
いただく。
実験局の免許を取得後ご使用いただく。
技術基準適合証明を取得後ご使用いただく。
なお、本製品は、上記の「ご使用にあたっての注意」を譲渡先、移転先に通知しない限り、譲渡、移転できないものとします。
上記を遵守頂けない場合は、電波法の罰則が適用される可能性があることをご留意ください。 日本テキサス・イ
ンスツルメンツ株式会社
東京都新宿区西新宿６丁目２４番１号
西新宿三井ビル
3.3.3
Notice for EVMs for Power Line Communication: Please see http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
電力線搬送波通信についての開発キットをお使いになる際の注意事項については、次のところをご覧くださ
い。http://www.tij.co.jp/lsds/ti_ja/general/eStore/notice_02.page
SPACER
4
EVM Use Restrictions and Warnings:
4.1 EVMS ARE NOT FOR USE IN FUNCTIONAL SAFETY AND/OR SAFETY CRITICAL EVALUATIONS, INCLUDING BUT NOT
LIMITED TO EVALUATIONS OF LIFE SUPPORT APPLICATIONS.
4.2 User must read and apply the user guide and other available documentation provided by TI regarding the EVM prior to handling
or using the EVM, including without limitation any warning or restriction notices. The notices contain important safety information
related to, for example, temperatures and voltages.
4.3 Safety-Related Warnings and Restrictions:
4.3.1
User shall operate the EVM within TI’s recommended specifications and environmental considerations stated in the user
guide, other available documentation provided by TI, and any other applicable requirements and employ reasonable and
customary safeguards. Exceeding the specified performance ratings and specifications (including but not limited to input
and output voltage, current, power, and environmental ranges) for the EVM may cause personal injury or death, or
property damage. If there are questions concerning performance ratings and specifications, User should contact a TI
field representative prior to connecting interface electronics including input power and intended loads. Any loads applied
outside of the specified output range may also result in unintended and/or inaccurate operation and/or possible
permanent damage to the EVM and/or interface electronics. Please consult the EVM user guide prior to connecting any
load to the EVM output. If there is uncertainty as to the load specification, please contact a TI field representative.
During normal operation, even with the inputs and outputs kept within the specified allowable ranges, some circuit
components may have elevated case temperatures. These components include but are not limited to linear regulators,
switching transistors, pass transistors, current sense resistors, and heat sinks, which can be identified using the
information in the associated documentation. When working with the EVM, please be aware that the EVM may become
very warm.
4.3.2
EVMs are intended solely for use by technically qualified, professional electronics experts who are familiar with the
dangers and application risks associated with handling electrical mechanical components, systems, and subsystems.
User assumes all responsibility and liability for proper and safe handling and use of the EVM by User or its employees,
affiliates, contractors or designees. User assumes all responsibility and liability to ensure that any interfaces (electronic
and/or mechanical) between the EVM and any human body are designed with suitable isolation and means to safely
limit accessible leakage currents to minimize the risk of electrical shock hazard. User assumes all responsibility and
liability for any improper or unsafe handling or use of the EVM by User or its employees, affiliates, contractors or
designees.
4.4 User assumes all responsibility and liability to determine whether the EVM is subject to any applicable international, federal,
state, or local laws and regulations related to User’s handling and use of the EVM and, if applicable, User assumes all
responsibility and liability for compliance in all respects with such laws and regulations. User assumes all responsibility and
liability for proper disposal and recycling of the EVM consistent with all applicable international, federal, state, and local
requirements.
5.
Accuracy of Information: To the extent TI provides information on the availability and function of EVMs, TI attempts to be as accurate
as possible. However, TI does not warrant the accuracy of EVM descriptions, EVM availability or other information on its websites as
accurate, complete, reliable, current, or error-free.
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
SPACER
6.
Disclaimers:
6.1 EXCEPT AS SET FORTH ABOVE, EVMS AND ANY WRITTEN DESIGN MATERIALS PROVIDED WITH THE EVM (AND THE
DESIGN OF THE EVM ITSELF) ARE PROVIDED "AS IS" AND "WITH ALL FAULTS." TI DISCLAIMS ALL OTHER
WARRANTIES, EXPRESS OR IMPLIED, REGARDING SUCH ITEMS, INCLUDING BUT NOT LIMITED TO ANY IMPLIED
WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF ANY
THIRD PARTY PATENTS, COPYRIGHTS, TRADE SECRETS OR OTHER INTELLECTUAL PROPERTY RIGHTS.
6.2 EXCEPT FOR THE LIMITED RIGHT TO USE THE EVM SET FORTH HEREIN, NOTHING IN THESE TERMS AND
CONDITIONS SHALL BE CONSTRUED AS GRANTING OR CONFERRING ANY RIGHTS BY LICENSE, PATENT, OR ANY
OTHER INDUSTRIAL OR INTELLECTUAL PROPERTY RIGHT OF TI, ITS SUPPLIERS/LICENSORS OR ANY OTHER THIRD
PARTY, TO USE THE EVM IN ANY FINISHED END-USER OR READY-TO-USE FINAL PRODUCT, OR FOR ANY
INVENTION, DISCOVERY OR IMPROVEMENT MADE, CONCEIVED OR ACQUIRED PRIOR TO OR AFTER DELIVERY OF
THE EVM.
7.
USER'S INDEMNITY OBLIGATIONS AND REPRESENTATIONS. USER WILL DEFEND, INDEMNIFY AND HOLD TI, ITS
LICENSORS AND THEIR REPRESENTATIVES HARMLESS FROM AND AGAINST ANY AND ALL CLAIMS, DAMAGES, LOSSES,
EXPENSES, COSTS AND LIABILITIES (COLLECTIVELY, "CLAIMS") ARISING OUT OF OR IN CONNECTION WITH ANY
HANDLING OR USE OF THE EVM THAT IS NOT IN ACCORDANCE WITH THESE TERMS AND CONDITIONS. THIS OBLIGATION
SHALL APPLY WHETHER CLAIMS ARISE UNDER STATUTE, REGULATION, OR THE LAW OF TORT, CONTRACT OR ANY
OTHER LEGAL THEORY, AND EVEN IF THE EVM FAILS TO PERFORM AS DESCRIBED OR EXPECTED.
8.
Limitations on Damages and Liability:
8.1 General Limitations. IN NO EVENT SHALL TI BE LIABLE FOR ANY SPECIAL, COLLATERAL, INDIRECT, PUNITIVE,
INCIDENTAL, CONSEQUENTIAL, OR EXEMPLARY DAMAGES IN CONNECTION WITH OR ARISING OUT OF THESE
TERMS ANDCONDITIONS OR THE USE OF THE EVMS PROVIDED HEREUNDER, REGARDLESS OF WHETHER TI HAS
BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. EXCLUDED DAMAGES INCLUDE, BUT ARE NOT LIMITED
TO, COST OF REMOVAL OR REINSTALLATION, ANCILLARY COSTS TO THE PROCUREMENT OF SUBSTITUTE GOODS
OR SERVICES, RETESTING, OUTSIDE COMPUTER TIME, LABOR COSTS, LOSS OF GOODWILL, LOSS OF PROFITS,
LOSS OF SAVINGS, LOSS OF USE, LOSS OF DATA, OR BUSINESS INTERRUPTION. NO CLAIM, SUIT OR ACTION SHALL
BE BROUGHT AGAINST TI MORE THAN ONE YEAR AFTER THE RELATED CAUSE OF ACTION HAS OCCURRED.
8.2 Specific Limitations. IN NO EVENT SHALL TI'S AGGREGATE LIABILITY FROM ANY WARRANTY OR OTHER OBLIGATION
ARISING OUT OF OR IN CONNECTION WITH THESE TERMS AND CONDITIONS, OR ANY USE OF ANY TI EVM
PROVIDED HEREUNDER, EXCEED THE TOTAL AMOUNT PAID TO TI FOR THE PARTICULAR UNITS SOLD UNDER
THESE TERMS AND CONDITIONS WITH RESPECT TO WHICH LOSSES OR DAMAGES ARE CLAIMED. THE EXISTENCE
OF MORE THAN ONE CLAIM AGAINST THE PARTICULAR UNITS SOLD TO USER UNDER THESE TERMS AND
CONDITIONS SHALL NOT ENLARGE OR EXTEND THIS LIMIT.
9.
Return Policy. Except as otherwise provided, TI does not offer any refunds, returns, or exchanges. Furthermore, no return of EVM(s)
will be accepted if the package has been opened and no return of the EVM(s) will be accepted if they are damaged or otherwise not in
a resalable condition. If User feels it has been incorrectly charged for the EVM(s) it ordered or that delivery violates the applicable
order, User should contact TI. All refunds will be made in full within thirty (30) working days from the return of the components(s),
excluding any postage or packaging costs.
10. Governing Law: These terms and conditions shall be governed by and interpreted in accordance with the laws of the State of Texas,
without reference to conflict-of-laws principles. User agrees that non-exclusive jurisdiction for any dispute arising out of or relating to
these terms and conditions lies within courts located in the State of Texas and consents to venue in Dallas County, Texas.
Notwithstanding the foregoing, any judgment may be enforced in any United States or foreign court, and TI may seek injunctive relief
in any United States or foreign court.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
spacer
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
工商网监
湘ICP备2023018690号
