CCM01 MK III
EMVTM compatible
CCM01 MK III connectors are intended for applications such as pay TV, home shopping and utility meters. Mainly driven by the Set Top Box market for payment and/or deciphering.
Construction Insulator Contacts Contact Finish PC tail plating Mechanical Data Thermoplastic UL94V-0 rated Copper alloy Gold over nickel Tin lead (2µ min.)
Features • Available in standard or reverse card reading version, with direct PCB soldering for reduced installation cost. • Panel mount version comes with improved noise reduction FPC, to accommodate all front panel configurations. • Double sided version allows the customer to insert the card chip up or down for easier handling. • Self cleaning card detection switch (normally closed) is protected against assembly mishandling. • Available with 8 through hole contacts specifically designed to reduce card wear. • A chamfer opening to the card entry slot improves the card guidance into the connector. • Variable distance from lower card side to PCB to level card slot with your front panel design • Easy insertion into PCB provided by four half pegs and termination true positioning insulator.1 • Four snap in board locks to lower stress on soldered terminals and improve interconnect PCB retention. • Thermoplastic UL 94 V-0 insulator suitable for wave soldering only • Designed to be compatible with: NDS EMVCo
Mechanical life Card insertion force Card extraction force Contact force Vibration Shock
30,000 cycles min 10 N max 1 N min /10 N max 0.20 N min / 0.60 N max Frequency 10 to 500 Hz. Acceleration 50m/s2 Duration 6 hours - amplitude 0,35 mm Max electrical discontinuity 1µs Peak value 500 m/s2 – Duration 11 ms 3 shocks in each direction of each axis Max electrical discontinuity 1 µs 1,000 MΩ min 100 mΩ max 10 µA min / 1 A max 750 Vrms min
Contact Electrical Data Insulation resistance Resistance Current rating Dielectric strength Switch Electrical Data Card detection switch Contact resistance Dielectric strength Current rating Maximum power Environmental Data Operating temperature Soldering temperature Damp heat Salt mist Ordering Code Designation Distance from lower card entrance & PCB 3,90 mm 6,75 mm 6,50 mm 8,00 mm Panel Mount Double Decker
Normally closed 100mΩ max 250 Vrms min 1 mA min / 10 mA max 0.2 VA
-20°C to +70°C Wave: 260°C / 5 seconds IEC 512 test number 11c (10 days) IEC 512 test number 11f (96 hours)
Standard Version
Reverse Version
CCM01-6101 CCM01-6105 CCM01-6103 CCM01-6301 CCM01-6402
CCM01-6201 CCM01-6202
CCM01-6302 CCM01-6403
1
Termination true positioning insulator not designed on low profile version 3,9 mm
EMVTM is a trademark owned by EMVCoLLC.
Packaging 30 per tray, 10 trays per box.
Dimensions are shown in mm Dimensions subject to change
www.ittcannon.com
10
CCM01 MK III
Dimensional Drawings CCM01-6101
61,1 ±0,2 54,2 +0,2 Card entry 0 Embossed Channel 6,8 (3,9)
4,2 3,9
0,9 ±0,05 Card entry
1,6 PCB Thickness
25˚ 4 Snap feet 10x 0,6 AB 29 A 22,12 0,7
3,81 3x 2,54
29 (50,3) (40)
Designation & Date-Code area
A 2,9±0,3
A-A 5,9 Card stop
2,54
0,75±0,25
40
6101 XXXX
36,4
B
19,05
10
10
A
Pick and place area ø8
AB
ø3,1
3,7±0,2 Card entry
PCB Layout CCM01-6101
(Component side) 22,12 24,66 27,2 29,74
33,55
Plastic outline 0
58
19,05 16,51 10
C1 C2 C3 C4 SW SW Card end travel switch terminals
Drawings shown for reference only. For other part numbers please consult your local Cannon Customer Service Center.
0
10
19,05 Contact location according to ISO 7816-2
C5 C6 C7 C8 1+0,1 10x ø0
(3,81) (3,81)
4x ø0,1 ø0,1
+0,1 ø 3,2 0
Unless otherwise stated, tolerances are ± 0,10 mm
4x
0,4
20
15,4±0,2
19,05
Dimensions are shown in mm Dimensions subject to change
www.ittcannon.com
11
(58)
6101 XXXX
CCM01 MK III
Dimensional Drawings
CCM01-6201
61,1 ±0,2 54,2 +0,2 Card entry 0 Embossed Channel 7,8 (3,9)
0,9 ±0,05 Card entry
1,6 PCB Thickness
25˚ 4 Snap feet 10x 3x 2,54 0,6 A B 29 A 0,7
3,81 22,12
4,2 3,9
(50,3) 29
(40)
Designation & Date-Code area
2,9 ±0,3
0,75 ±0,25
19,05
40
10
6201 XXXX
36,4
AB
ø 3,1
A 4x 0,4
3,7 ±0,2 Card entry
PCB Layout CCM01-6201
(Component side)
29,74 27,2 24,66 22,12
18,31
Plastic outline 58
19,05 16,51 10
C8 C7 C6 C5 SW
0
C4 C3 C2 C1 SW
Card end travel switch terminals
Drawings shown for reference only. For other part numbers please consult your local Cannon Customer Service Center.
0
10
Contact location according to ISO 7816-2
+0,1 ø 10 10x
(3,81 (3,81 ))
4x ø0,1 ø0,1
+0,1 ø3,2 0
Unless otherwise stated, tolerances are ± 0,10 mm
20
15,4 ±0,2
16,51
B
10
Card stop
A
A-A 5,9
Dimensions are shown in mm Dimensions subject to change
www.ittcannon.com
12
(58)