AN18165B

DATA SHEET Part No. Package Code No. AN18165B SSOP024-P-0300E Publication date: May 2007 SDC00068AEB 1 AN18165B Contents Overview ………………………………………………….…………………………………………………………. 3 Features ………………………………………………….…………………………………………………………. 3 Applications ……………………………………………….…………………………………………………………. 3 Package ………………………………………………….…………………………………………………………. 3 Type ……………………………………………………….…………………………………………………………. 3 Application Circuit Example (Block Diagram)………….…………………………………………………………. 4 Pin Descriptions ……………………………………….……………………………………………………………. 5 Absolute Maximum Ratings …………………………….…………………………………………………………. 6 Operating Supply Voltage Range ……………………….………………………………………………………… 6 Allowed Voltage Ranges …………………………….……………………………………………………………. 6 SDC00068AEB 2 AN18165B AN18165B FM-MPX demodulation / FM noise canceller for car radio Overview AN18165B is an IC for FM-MPX demodulation for car radio and FM noise canceller. This IC is enable to adjust and change over various function by I2C-bus, and built-in VCO reduces the number of parts. Features I2C-bus control FM-MPX demodulation Built-in FM noise canceller (PNL) Built-in VCO(No cellalock required) Applications Car radio Package 24 pin plastic shrink small outline package (SSOP Type) Type Silicon monolithic bipolar IC SDC00068AEB 3 AN18165B Application Circuit Example / Block Diagram VDD = 5 V 27 kΩ R-ch. 0.022 μF 13 14 0.022 μF 0.01 μF 0.01 μF 0.1 μF ATC-R Iref 12 I2C 27 kΩ L-ch. ATC-L ATC Bgap DAC 11 VST 15 Matrix ASC 10 SDA 16 SEP ADJ 9 SCL 17 18 19 GP AM/FM-SW Dev. 1/2, 4, 8 Sdet Pdet Gate PD LAMP PD VCO 8 7 1 μF 270 kΩ 0.01 μF 0.01 μF 6 0.1 μF Vin1 20 21 AGC 5 4 Vcont HPF VCC 1 μF 22 23 LPF Pcan BUFF PD Qsin VCC 3 LPF MPdet ASC 2 1 0.1 μF 0.1 μF 24 0.1 μF 22 kΩ 0.1 μF Vin2 SDC00068AEB 4 AN18165B Pin Descriptions Pin No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 Pin name FMIN ASCTC N.C. VCC VCONTIN AMIN PDLPF VSS SCL SDA STIND N.C. ROUT LOUT LATCLPF RATCLPF PNLAGC FMATCTC PNLHOLD GND N.C. PCLPF N.C. PLLLPF Type Input — — Power supply Input Input — Ground Input Input Output — Output Output — — Output — Output Ground — — — — FM input ASC time constant Non connected VCC FM Control voltage input AM input Pilot detection low-pass filter VSS (Logic-GND) SCL SDA Stereo indicator Non connected R-ch. output L-ch. output L-ch. FM-ATC low-pass filter R-ch. FM-ATC low-pass filter PNL AGC FM-ATC time constant PNL output hold Ground Non connected Pilot cancellation control low-pass filter Non connected PLL low-pass filter Description SDC00068AEB 5 AN18165B Absolute Maximum Ratings A No. 1 2 3 4 5 Parameter Supply voltage Supply current Power dissipation Operating ambient temperature Storage temperature Symbol VCC ICC PD Topr Tstg Rating 9.1 28 156 –40 to +85 –55 to +125 Unit V mA mW °C °C Notes *1 ⎯ *2 *3 *3 Notes) *1: The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. *2: The power dissipation shown is the value at Ta = 85°C for the independent (unmounted) IC package without a heat sink. *3: Except for the power dissipation, operating ambient temperature, and storage temperature, all ratings are for Ta = 25°C. Operating supply voltage range Parameter Supply voltage range Symbol VCC Range 7.2 to 9.0 Unit V Notes * Note) *: The values under the condition not exceeding the above absolute maximum ratings and the power dissipation. Allowable Voltage Ranges Pin No. 4 5 9 10 11 Note) Pin name VCC VCONTIN SCL SDA STIND Range 0 to 9.0 0 to 5.5 0 to 5.5 0 to 5.5 0 to 5.5 Unit V V V V V Notes — — — — — 1. The ranges on the list are the voltages of respective pins in relation to GND. The GND represents the voltage of GND and VSS. And GND=VSS. 2. Do not apply the voltages or the currents from external into the pins which are not on the list. SDC00068AEB 6 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd.