MN101CF91D

MN101CF91D Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) Minimum Instruction Execution Time MN101CF91D FLASH 64K 4K TQFP048-P-0707B 0.1 µs (at 2.7 V to 3.6 V, 10 MHz) 62.5 µs (at 2.7 V to 3.6 V, 32 kHz)  Interrupts RESET, Watchdog, External 0 to 5, External 6 (key interrupt dedicated), Timer 0 to 4, Timer 6, Timer 7 (2 systems), Timer 8 (2 systems), Time base, Serial 0 (2 systems), Serial 1 (2 systems), Serial 2 (3 systems), A/D conversion finish Timer counter 0 : 8-bit × 1 (square-wave output, PWM output, event count, simple pulse width measurement) (square-wave/PWM output to large current terminal P50 (TM0OA) or P30 (TM0OB) possible) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 0 Timer counter 1 : 8-bit × 1 (square-wave output, event count, serial transfer clock) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 1 Timer counter 0, 1 can be cascade-connected.  Timer Counter Timer counter 2 : 8-bit × 1 (square-wave output, PWM output, event count, simple pulse width measurement, serial transfer clock) (square-wave/PWM output to large current terminal P52 (TM2OA) or P32 (TM2OB) possible) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 2 Timer counter 3 : 8-bit × 1 (square-wave output, event count) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 4 : 8-bit × 1 (square-wave output, PWM output, event count, simple pulse width measurement) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 4 Timer counter 6 : 8-bit freerun timer Clock source................ 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of OSC oscillation clock frequency; 1/1, 1/128, 1/8192 of XI oscillation clock frequency Interrupt source ........... coincidence with compare register 6 Timer counter 7 : 16-bit × 1 (square-wave output, PWM output (cycle / duty continuous variable), event count, pulse width measurement, input capture) (square-wave/PWM output to large current terminal P51 (TM7O) possible) Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ........... coincidence with compare register 7 (2 lines), input capture register Timer counter 8 : 16 bit × 1 (square-wave output, PWM output (cycle / duty continuous variable), event count, pulse width measurement, input capture) (square-wave/PWM output to large current terminal P53 (TM8O) possible) Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ........... coincidence with compare register 8 (2 lines), input capture register MAD00055CEM MN101CF91D Time base timer (one-minute count setting) Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/4096, 1/8192, 1/16384, 1/32768 of clock source frequency Watchdog timer Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency  Serial interface Serial 0 : synchronous type/UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency, external clock Serial 1 : synchronous type/UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1 or 2; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency, external clock Serial 2 : synchronous type/multi-master I²C × 1(applicable for 7-bit/10-bit address setting, general call, SMBus)  I/O Pins I/O 37 Common use , Specified pull-up resistor available, Input/output selectable (bit unit)  A/D converter  Special Ports 10-bit × 6-ch. (with S/H) Buzzer output, remote control carrier signal output, high-current drive port, clock output Correcting address designation : up to 3 addresses possible In-circuit Emulator PX-ICE101C/D+PX-PRB101C91-TQFP048-P-0707B-CN-M  ROM Correction  Development tools  Pin Assignment P35, KEY5, NBUZZER P36, KEY6, CLKOUT P34, KEY4, BUZZER P32, KEY2, TM2OB P30, KEY0, TM0OB P33, KEY3, TM3IO P31, KEY1, TM1IO P23, IRQ3 P22, IRQ2 27 P21, IRQ1 26 36 35 34 33 32 31 30 29 28 P40, RXD0B, SBI0B P41, TXD0B, SBO0B P42, SBT0B P43, RXD1B, SBI1B P44, TXD1B, SBO1B P45, SBT1B P50, LED0, TM0OA P51, LED1, TM7O P52, LED2, TM2OA P53, LED3, TM8O P54, LED4, IRQ4 P55, LED5, IRQ5 37 38 39 40 41 42 43 44 45 46 47 48 25 P20, IRQ0 24 23 22 21 20 19 18 17 16 15 14 13 DMOD SCL2, SBT2, P16 SDA2, SBO2, P15 TM4IO, SBI2, P14 TM8IO, P13 TM7IO, P12 TM2IO, P11 RMOUT, TM0IO, P10 SBT1A, AN5, P05 TXD1A, SBO1A, AN4, P04 RXD1A, SBI1A, AN3, P03 SBT0A, AN2, P02 TXD0A, SBO0A, AN1, P01 MN101CF91D 10 OSCMOD VDD18 MMOD VDD33 VREF+ XI OSC2 OSC1 VSS XO TQFP048-P-0707B MAD00055CEM RXD0A, SBI0A, AN0, P00 NRST, P27 12 11 1 2 3 4 5 6 7 8 9 Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.