MN101CF95G

MN101CF95F, MN101CF95G Type Internal ROM type ROM (byte) RAM (byte) Package (Lead-free) 96K 4K TQFP080-P-1212D (Under planning) MN101CF95F FLASH 128K 6K TQFP080-P-1212D (Under development) [Standard] 0.2 µs (at 2.7 V to 3.6 V, 10 MHz) 0.5 µs (at 2.7 V to 3.6 V, 4 MHz) 62.5 µs (at 2.7 V to 3.6 V, 32 kHz) [Double speed] 0.1 µs (at 2.7 V to 3.6 V, 10 MHz) MN101CF95G Minimum Instruction Execution Time  Interrupts RESET, Watchdog, External 0 to 5, Timer 0 to 8, Time base, Serial 0 reception, Serial 0 transmission, Serial 1 reception, Serial 1 transmission, Serial 2, Serial 3, Serial 4 reception, Serial 4 transmission, Automatic transfer finish, A/D conversion finish, Key interrupts (12 lines) Timer counter 0 : 8-bit × 1 (square-wave/8-bit PWM output, event count, pulse width measurement, serial clock output, real-time output control, generation of remote control carrier) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 0 Timer counter 1 : 8-bit × 1 (square-wave output, event count, synchronous output event, serial clock output) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 1 Timer counter 0, 1 can be cascade-connected.  Timer Counter Timer counter 2 : 8-bit × 1 (square-wave output, PWM output, event count, pulse width measurement, synchronous timer, serial clock output) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 2 Timer counter 0, 1, 2 can be cascade-connected. Timer counter 3 : 8-bit × 1 (square-wave output, event count, serial clock output) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 3 Timer counter 2, 3 can be cascade-connected. Timer counter 0, 1, 2, 3 can be cascade-connected. Timer counter 4 : 8-bit × 1 (square-wave/8-bit PWM output, event count, pulse width measurement, real-time output control, serial clock output) Clock source................ 1/2, 1/4 of system clock frequency; 1/1, 1/4, 1/16, 1/32, 1/64 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; 1/1 of external clock input frequency Interrupt source ........... coincidence with compare register 4 Timer counter 5 : 8-bit × 1 (square-wave/8-bit PWM output, event count, pulse width measurement, serial clock output) Clock source................ 1/2, 1/8 of system clock frequency; 1/1, 1/4, 1/16, 1/64, 1/128 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency; external clock input Interrupt source ........... coincidence with compare register 5 Timer counter 4, 5 can be cascade-connected. MAD00053CEM MN101CF95F, MN101CF95G Timer counter 6 : 8-bit freerun timer Clock source................ 1/1 of system clock frequency; 1/1, 1/128, 1/8192 of OSC oscillation clock frequency; 1/1, 1/128, 1/8192 of XI oscillation clock frequency Interrupt source ........... coincidence with compare register 6 Timer counter 7 : 16-bit × 1 (square-wave/16-bit PWM output, cycle / duty continuous variable, event count, synchronous output evevt, pulse width measurement, input capture, real-time output control) Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ........... coincidence with compare register 7 (2 lines) Timer counter 8 : 16-bit × 1 (square-wave output, PWM output (duty continuous variable), event count, pulse width measurement, input capture) Clock source................ 1/1, 1/2, 1/4, 1/16 of system clock frequency; 1/1, 1/2, 1/4, 1/16 of OSC oscillation clock frequency; 1/1, 1/2, 1/4, 1/16 of external clock input frequency Interrupt source ........... coincidence with compare register 8 (2 lines) Time base timer (one-minute count setting) Clock source................ 1/1 of OSC oscillation clock frequency; 1/1 of XI oscillation clock frequency Interrupt source ........... 1/128, 1/256, 1/512, 1/1024, 1/8192, 1/32768 of clock source frequency Watchdog timer Interrupt source ........... 1/65536, 1/262144, 1/1048576 of system clock frequency  Serial interface Serial 0 : synchronous type / UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 1, 2; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency Serial 1 : synchronous type / UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 2, 3; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency Serial 2 : synchronous type / multi-master I²C × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 3, 4; 1/2, 1/4, 1/16, 1/32 of OSC oscillation clock frequency Serial 3 : synchronous type / single-master I²C × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 4, 5; 1/2, 1/4, 1/16, 1/32 of OSC oscillation clock frequency Serial 4 : synchronous type / UART (full-duplex) × 1 Clock source................ 1/2, 1/4 of system clock frequency; pulse output of timer counter 0, 5; 1/2, 1/4, 1/16, 1/64 of OSC oscillation clock frequency  DMA controller Max. Transfer cycles : 255 Starting factor : various types of interrupt, software Transfer mode : 1-byte transfer, word transfer, burst transfer  I/O Pins I/O 67 Common use , Specified pull-up resistor available, Input/output selectable (bit unit)  A/D converter  Special Ports 10-bit × 11-ch. (with S/H) Buzzer output, remote control carrier signal output, high-current drive port In-circuit Emulator PX-ICE101C/D+PX-PRB101C95-TQFP080-P-1212D  Development tools MAD00053CEM  Pin Assignment P54, TM1IO, TM0OB, RMOUTB 42 P70, SDO0, SBO1B, TXD1B P71, SDO1, SBI1B, RXD1B P53, TM0IOA, RMOUTA 41 P74, SDO4, TM7OB P75, SDO5, TM8IO P72, SDO2, SBT1B P42, KEY10 P43, KEY11 P41, KEY9 P40, KEY8 P67, KEY7 P66, KEY6 P65, KEY5 P64, KEY4 P63, KEY3 P62, KEY2 45 P61, KEY1 44 60 59 58 57 56 55 54 53 52 51 50 49 48 47 46 TM4IO, SDO6, P76 TM5IO, SDO7, P77 LED7, P87 LED6, P86 SBT0A, LED5, P85 RXD0A, SBI0A, LED4, P84 TXD0A, SBO0A, LED3, P83 LED2, P82 LED1, P81 LED0, P80 KEY12, P44 KEY13, P45 KEY14, P46 KEY15, P47 VREFAN0, PA0 AN1, PA1 AN2, PA2 AN3, PA3 AN4, PA4 43 P60, KEY0 P73, SDO3 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 40 39 38 37 36 35 34 33 32 31 30 29 28 27 26 25 24 23 22 21 P25, IRQ5, TM7IOA P24, IRQ4 P23, IRQ3 P22, IRQ2 P21, IRQ1 P20, IRQ0 P36 P35, SBT4 P34, SBI4, RXD4 P33, SBO4, TXD4 P32, TM3IO P31, TM2OB P30, TM2IOA P15, SBT2, SCL2, SBT0B P14, SBI2, SBI0B, RXD0B P13, SBO2, SDA2, SBO0B, TXD0B P12, SBT1A P11, SBI1A, RXD1A P10, SBO1A, TXD1A P02, SBT3, SCL3, BUZZER MN101CF95F MN101CF95G 10 12 13 14 15 16 17 18 P27, NRST 19 SDA3, SBO3, P00 VREF+ XI AN7, PB0 AN8, PB1 AN9, PB2 AN10, PB3 AN5, PA5 AN6, PA6 TQFP080-P-1212D SBI3, P01 OSC2 OSC1 VPP VDD33 VDD18 VSS XO MMOD DMOD 20 11 1 2 3 4 5 6 7 8 9 MAD00053CEM Request for your special attention and precautions in using the technical information and semiconductors described in this book (1) If any of the products or technical information described in this book is to be exported or provided to non-residents, the laws and regulations of the exporting country, especially, those with regard to security export control, must be observed. (2) The technical information described in this book is intended only to show the main characteristics and application circuit examples of the products, and no license is granted under any intellectual property right or other right owned by our company or any other company. Therefore, no responsibility is assumed by our company as to the infringement upon any such right owned by any other company which may arise as a result of the use of technical information described in this book. (3) The products described in this book are intended to be used for standard applications or general electronic equipment (such as office equipment, communications equipment, measuring instruments and household appliances). Consult our sales staff in advance for information on the following applications: – Special applications (such as for airplanes, aerospace, automobiles, traffic control equipment, combustion equipment, life support systems and safety devices) in which exceptional quality and reliability are required, or if the failure or malfunction of the products may directly jeopardize life or harm the human body. – Any applications other than the standard applications intended. (4) The products and product specifications described in this book are subject to change without notice for modification and/or improvement. At the final stage of your design, purchasing, or use of the products, therefore, ask for the most up-to-date Product Standards in advance to make sure that the latest specifications satisfy your requirements. (5) When designing your equipment, comply with the range of absolute maximum rating and the guaranteed operating conditions (operating power supply voltage and operating environment etc.). Especially, please be careful not to exceed the range of absolute maximum rating on the transient state, such as power-on, power-off and mode-switching. Otherwise, we will not be liable for any defect which may arise later in your equipment. Even when the products are used within the guaranteed values, take into the consideration of incidence of break down and failure mode, possible to occur to semiconductor products. Measures on the systems such as redundant design, arresting the spread of fire or preventing glitch are recommended in order to prevent physical injury, fire, social damages, for example, by using the products. (6) Comply with the instructions for use in order to prevent breakdown and characteristics change due to external factors (ESD, EOS, thermal stress and mechanical stress) at the time of handling, mounting or at customer's process. When using products for which damp-proof packing is required, satisfy the conditions, such as shelf life and the elapsed time since first opening the packages. (7) This book may be not reprinted or reproduced whether wholly or partially, without the prior written permission of Matsushita Electric Industrial Co., Ltd. Industrial Co., Ltd.