6N135

HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 DESCRIPTION The HCPL-4502/HCPL-2503, 6N135/6 and HCPL-2530/HCPL-2531 optocouplers consist of an AlGaAs LED optically coupled to a high speed photodetector transistor. A separate connection for the bias of the photodiode improves the speed by several orders of magnitude over conventional phototransistor optocouplers by reducing the base-collector capacitance of the input transistor. An internal noise shield provides superior common mode rejection of 10kV/µs. An improved package allows superior insulation permitting a 480 V working voltage compared to industry standard 0f 220 V. 8 1 DUAL-CHANNEL HCPL-2530 HCPL-2531 FEATURES • High speed-1 MBit/s • Superior CMR-10 kV/µs • Dual-Channel HCPL-2530/HCPL-2531 • Double working voltage-480V RMS • CTR guaranteed 0-70°C • U.L. recognized (File # E90700) N/C 1 8 VCC +1 VF1 +2 VF _ 3 6 VO _ 3 6 V02 7 VB _ 2 7 V01 8 VCC 8 1 8 1 VF2 N/C 4 5 GND +4 5 GND APPLICATIONS • • • • Line receivers Pulse transformer replacement Output interface to CMOS-LSTTL-TTL Wide bandwidth analog coupling 6N135, 6N136, HCPL-2503, HCPL-4502 Pin 7 is not connected in Part Number HCPL-4502 HCPL-2530/HCPL-2531 ABSOLUTE MAXIMUM RATINGS (TA = 25°C unless otherwise specified) Symbol TSTG TOPR TSOL IF (avg) IF (pk) IF (trans) VR PD IO (avg) IO (pk) VEBR VCC VO IB PD Value -55 to +125 -55 to +100 260 for 10 sec 25 50 1.0 5 100 45 8 16 5 -0.5 to 30 -0.5 to 20 5 100 35 Units °C °C °C mA mA A V mW mA mA V V V mA mW mW Parameter Storage Temperature Operating Temperature Lead Solder Temperature EMITTER DC/Average Forward Input Current Each Channel (Note 1) Peak Forward Input Current (50% duty cycle, 1 ms P.W.) Each Channel (Note 2) Peak Transient Input Current - (!"1 µs P.W., 300 pps) Each Channel Reverse Input Voltage Each Channel (6N135/6N136 and HCPL-2503/4502) Input Power Dissipation (HCPL-2530/2531 ) Each Channel (Note 3) DETECTOR Average Output Current Each Channel Peak Output Current Each Channel Emitter-Base Reverse Voltage (6N135, 6N136 and HCPL-2503 only) Supply Voltage Output Voltage Base Current (6N135, 6N136 and HCPL-2503 only) Output power (6N135, 6N136, HCPL-2503, HCPL-4502) (Note 4) dissipation (HCPL-2530, HCPL-2531) Each Channel 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 ELECTRICAL CHARACTERISTICS Parameter EMITTER Input Forward Voltage Input Reverse Breakdown Voltage Temperature coefficient of forward voltage DETECTOR (IF = 0 mA, VO = VCC = 5.5 V) (TA =25°C) Logic high output current (IF = 0 mA, VO = VCC = 15 V) (TA =25°C) (IF = 0 mA, VO = VCC = 15 V) (IF = 16 mA, VO = Open) Logic low supply current (VCC = 15 V) (IF1 = IF2 = 16 mA, VO = Open) (VCC = 15 V) (IF = 0 mA, VO = Open, VCC = 15 V) (TA =25°C) ICCL IOH 6N135 6N136 HCPL-4502 HCPL-2503 All 6N135 6N136 HCPL-4502 HCPL-2503 HCPL-2530 HCPL-2531 6N135 6N136 HCPL-4502 HCPL-2503 Logic high supply current (IF = 0 mA, VO = Open) (VCC = 15 V) (IF = 0 mA, VO = Open) (VCC = 15 V) ** All typicals at TA = 25°C ICCH 6N135 6N136 HCPL-4502 HCPL-2503 HCPL-2530 HCPL-2531 0.02 4 2 µA 1 200 400 120 200 µA 50 0.005 1 µA All 0.001 0.5 (TA = 0 to 70°C Unless otherwise specified) DUAL-CHANNEL HCPL-2530 HCPL-2531 INDIVIDUAL COMPONENT CHARACTERISTICS Test Conditions (IF = 16 mA, TA =25°C) (IF = 16 mA) (IR = 10 µA) (IF = 16 mA) Symbol VF BVR (#VF/#TA) 5.0 -1.6 Device Min Typ** 1.45 Max 1.7 1.8 Unit V V mV/°C 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 TRANSFER CHARACTERISTICS Parameter COUPLED (IF = 16 mA, VO = 0.4 V) (VCC = 4.5 V, TA =25°C) (TA = 0 to 70°C Unless otherwise specified) Test Conditions Symbol Device 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2531 Current transfer ratio (Note 5) (IF = 16 mA, VO = 0.5 V) (VCC = 4.5 V) CTR HCPL-2503 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2531 HCPL-2503 (IF = 16 mA, IO = 1.1 mA) (VCC = 4.5 V, TA =25°C) (IF = 16 mA, IO = 3 mA) (VCC = 4.5 V, TA =25°C) Logic low output voltage output voltage (IF = 16 mA, IO = 0.8 mA) (VCC = 4.5 V) (IF = 16 mA, IO = 2.4 mA) (VCC = 4.5 V) VOL 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2503 HCPL-2531 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2503 HCPL-2531 ** All typicals at TA = 25°C 0.5 0.25 0.5 0.5 V 0.25 0.4 9 30 0.18 0.18 0.4 0.5 % 15 30 % 12 5 27 21 % % 19 27 50 % Min 7 Typ** 18 Max 50 Unit % DUAL-CHANNEL HCPL-2530 HCPL-2531 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 SWITCHING CHARACTERISTICS Parameter DUAL-CHANNEL HCPL-2530 HCPL-2531 (TA = 0 to 70°C unless otherwise specified., VCC = 5 V) Symbol Device 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2503 TPHL HCPL-2531 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2503 HCPL-2531 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2503 TPLH HCPL-2531 6N135 HCPL-2530 6N136 HCPL-4502 HCPL-2503 HCPL-2531 6N135 HCPL-2530 |CMH| 6N136 HCPL-4502 HCPL-2503 HCPL-2531 6N135 HCPL-2530 |CML| 6N136 HCPL-4502 HCPL-2503 HCPL-2531 10,000 V/µs 10,000 V/µs 2.0 µs 2.0 µs Min Typ** 0.45 Max 1.5 Unit µs Test Conditions TA = 25°C, (RL = 4.1 k$, IF = 16 mA) (Note 6) (Fig. 7) (RL = 1.9 k$, IF = 16 mA) (Note 7) (Fig. 7) Propagation delay time to logic low (RL = 4.1 k$, IF = 16 mA) (Note 6) (Fig. 7) TA = 25°C 0.45 0.8 µs (RL = 1.9 k$, IF = 16 mA) (Note 7) (Fig. 7) 1.0 µs TA = 25°C, (RL = 4.1 k$, IF = 16 mA) (Note 6) (Fig. 7) 0.5 1.5 µs (RL = 1.9 k$, IF = 16 mA) (Note 7) (Fig. 7) TA = 25°C Propagation delay time to logic high (RL = 4.1 k$, IF = 16 mA) (Note 6) (Fig. 7) 0.3 0.8 µs (RL = 1.9 k$, IF = 16 mA) (Note 7) (Fig. 7) 1.0 µs (IF = 0 mA, VCM = 10 VP-P, RL = 4.1 k$) Common mode transient immunity at logic high (Note 8) (Fig. 8) TA = 25°C (IF = 0 mA, VCM = 10 VP-P) TA = 25°C, (RL = 1.9 k$) (Note 8) (Fig. 8) (IF = 16 mA, VCM = 10 VP-P, RL = 4.1 k$) Common mode transient immunity at logic low ** All typicals at TA = 25°C (Note 8) (Fig. 8) TA = 25°C (IF = 16 mA, VCM = 10 VP-P) (RL = 1.9 k$) (Note 8) (Fig. 8) 10,000 V/µs 10,000 V/µs 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 ISOLATION CHARACTERISTICS Characteristics Input-output insulation leakage current (TA = 0 to 70°C Unless otherwise specified) Test Conditions (Relative humidity = 45%) (TA = 25°C, t = 5 s) (VI-O = 3000 VDC) (Note 9) Withstand insulation test voltage Resistance (input to output) Capacitance (input to output) DC Current gain Input-Input Insulation leakage current Input-Input Resistance Input-Input Capacitance ** All typicals at TA = 25°C (RH ! 50%, TA = 25°C) (Note 9) ( t = 1 min.) (Note 9) (VI-O = 500 VDC) (Note 9) (f = 1 MHz) (IO = 3 mA, VO = 5 V) (RH ! 45%, VI-I = 500 VDC) (Note 10) t = 5 s, (HCPL-2530/2531 only) (VI-I = 500 VDC) (Note 10) (HCPL-2530/2531 only) (f = 1 MHz) (Note 10) (HCPL-2530/2531 only) VISO RI-O CI-O HFE II-I RI-I CI-I 2500 1012 0.6 150 0.005 1011 0.03 µA $ pF VRMS $ pF II-O 1.0 µA Symbol Min Typ** Max Unit DUAL-CHANNEL HCPL-2530 HCPL-2531 NOTES Derate linearly above 70°C free-air temperature at a rate of 0.8 mA/°C. Derate linearly above 70°C free-air temperature at a rate of 1.6 mA/°C. Derate linearly above 70°C free-air temperature at a rate of 0.9 mW/°C. Derate linearly above 70°C free-air temperature at a rate of 2.0 mW/°C. Current Transfer Ratio is defined as a ratio of output collector current, IO, to the forward LED input current, IF, times 100%. The 4.1 k$"load represents 1 LSTTL unit load of 0.36 mA and 6.1k$"pull-up resistor. The 1.9 k$"load represents 1 TTL unit load of 1.6 mA and 5.6 k$"pull-up resistor. Common mode transient immunity in logic high level is the maximum tolerable (positive) dVcm/dt on the leading edge of the common mode pulse signal VCM, to assure that the output will remain in a logic high state (i.e., VO%2.0 V). Common mode transient immunity in logic low level is the maximum tolerable (negative) dVcm/dt on the trailing edge of the common mode pulse signal, VCM, to assure that the output will remain in a logic low state (i.e., VO&0.8 V). 9. Device is considered a two terminal device: Pins 1, 2, 3 and 4 are shorted together and Pins 5, 6, 7 and 8 are shorted together. 10. Measured between pins 1 and 2 shorted together, and pins 3 and 4 shorted together. 1. 2. 3. 4. 5. 6. 7. 8. 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 Fig. 1 Normalized CTR vs. Forward Current 1.2 1.2 DUAL-CHANNEL HCPL-2530 HCPL-2531 Fig. 2 Normalized CTR vs. Temperature 1.0 1.0 NORMALIZED CTR 0.8 NORMALIZED CTR 0.8 0.6 0.6 0.4 Normalized to: IF = 16 mA 0.2 VO = 0.4 V VCC = 5 V TA = 25˚C 0.4 Normalized to: TA = 25˚C 0.2 IF = 16mA VCC = 5 V VO = 0.4 V 0.0 0.1 1 10 100 0.0 -60 -40 -20 0 20 40 60 80 100 IF - FORWARD CURRENT (mA) TA - TEMPERATURE (˚C) Fig. 3 Output Current vs. Output Voltage 16 14 TA = 25˚C VCC = 5 V IF = 40 mA IF = 35 mA 12 10 8 6 4 2 0 0 2 4 6 8 10 12 14 16 18 20 IF = 30 mA IF = 25 mA IF = 20 mA IF = 15 mA IF = 10 mA IF = 5 mA 1000 Fig. 4 Logic High Output Current vs. Temperature IOH - LOGIC HIGH OUTPUT CURRENT (nA) IF = 0 mA VCC = 5 V VO = 5 V 100 IO - OUTPUT CURRENT (mA) 10 1 0.1 -60 -40 -20 0 20 40 60 80 100 VO - OUTPUT VOLTAGE (V) TA - TEMPERATURE (˚C) Fig. 5 Propagation Delay vs. Temperature 800 700 10000 Fig. 6 Propagation Delay vs. Load Resistance Tp - PROPAGATION DELAY (ns) 600 500 400 300 200 RL = 4.1 K (TPLH) TP - PROPAGATION DELAY (ns) RL = 4.1 K (TPLH) IF - 16 mA (TPHL) IF - 10 mA (TPHL) 1000 IF - 16 mA (TPLH) RL = 1.9 K (TPHL) 100 0 -60 RL = 1.9 K (TPLH) IF = 16 mA VCC = 5 V IF - 10 mA (TPLH) -40 -20 0 20 40 60 80 100 100 1 VCC = 5 V TA = 25˚C 10 TA - TEMPERATURE (˚C) RL = LOAD RESISTANCE (k$) 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 DUAL-CHANNEL HCPL-2530 HCPL-2531 Pulse Generator I F tr = 5ns Z O = 50 $ 10% D.C. I/ f< 100 ' s 1 + Noise Shield 8 7 6 5 VCC +5 V Pulse Generator tr = 5ns Z O = 50 $ IF + Noise Shield 1 VF1 - 8 7 6 5 VCC RL +5 V 2 VF - VB RL 10% DUTY CYCLE I/f < 100 µS VO 2 3 4 V01 VO C L = 1.5 µF 3 I F Monitor Rm VO 0.1 µF IF MONITOR VF2 + Rm V02 0.1 µF 4 GND GND C L = 1.5 µF Test Circuit for 6N135, 6N136, HCPL-2503 and HCPL- 4502 Test Circuit for HCPL-2530 and HCPL-2531 IF 0 VO 5V 1.5 V 1.5 V VOL TPHL TPLH Fig. 7 Switching Time Test Circuit IF 1 + Noise Shield 8 7 6 5 VCC +5 V IF + VF1 A Noise Shield 1 2 3 4 8 7 6 5 VCC RL V01 +5 V 2 A B VFF VF - VB RL VO 3 4 + VCM VO VO 0.1 µF B VFF VF2 + V02 0.1 µF GND - GND - Pulse Gen + VCM - Pulse Gen Test Circuit for 6N135, 6N136, HCPL-2503 and HCPL-4502 Test Circuit for HCPL-2530 and HCPL-2531 VCM 10 V 10% tr 90% 90% 10% tf 0V VO Switch at A : I F= 0 mA VO Switch at A : I F= 16 mA 5V VOL Fig. 8 Common Mode Immunity Test Circuit 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 Package Dimensions (Through Hole) PIN 1 ID. DUAL-CHANNEL HCPL-2530 HCPL-2531 Package Dimensions (Surface Mount) 0.390 (9.91) 0.370 (9.40) 4 4 3 2 1 0.270 (6.86) 0.250 (6.35) 5 6 7 8 3 2 1 PIN 1 ID. 0.270 (6.86) 0.250 (6.35) 0.390 (9.91) 0.370 (9.40) 5 0.070 (1.78) 0.045 (1.14) 6 7 8 SEATING PLANE 0.070 (1.78) 0.045 (1.14) 0.300 (7.62) TYP 0.200 (5.08) 0.115 (2.92) 0.020 (0.51) MIN 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) 0.020 (0.51) MIN 0.016 (0.41) 0.008 (0.20) 0.045 [1.14] 15° MAX 0.016 (0.40) 0.008 (0.20) 0.100 (2.54) TYP 0.300 (7.62) TYP 0.022 (0.56) 0.016 (0.41) 0.100 (2.54) TYP 0.315 (8.00) MIN 0.405 (10.30) MIN Lead Coplanarity : 0.004 (0.10) MAX Package Dimensions (0.4”Lead Spacing) 4 3 2 1 PIN 1 ID. 0.270 (6.86) 0.250 (6.35) 5 6 7 8 0.390 (9.91) 0.370 (9.40) SEATING PLANE 0.070 (1.78) 0.045 (1.14) 0.200 (5.08) 0.115 (2.92) 0.004 (0.10) MIN 0.154 (3.90) 0.120 (3.05) 0.022 (0.56) 0.016 (0.41) NOTE All dimensions are in inches (millimeters) 0° to15° 0.016 (0.40) 0.008 (0.20) 0.100 (2.54) TYP 0.400 (10.16) TYP www.qtopto.com Call QT Optoelectronics for more information or the phone number of your nearest distributor. United States 800-533-6786 • France 33 [0] 1.45.18.78.78 • Germany 49 [0] 89/96.30.51 • United Kingdom 44 [0] 1296 394499 • Asia/Pacific 603-7352417 200004A HIGH SPEED TRANSISTOR OPTOCOUPLERS SINGLE-CHANNEL 6N135, 6N136 HCPL-2503 HCPL-4502 Order Entry Identifier .R2 .S .SD .SDL .W DUAL-CHANNEL HCPL-2530 HCPL-2531 ORDERING INFORMATION Option R2 S SD SDL W Description Opto Plus Reliability Conditioning Surface Mount Lead Bend Surface Mount; Tape and reel Surface Mount; Tape and reel 0.4” Lead Spacing QT Carrier Tape Specifications (“D” Taping Orientation) 12.0 ± 0.1 4.90 ± 0.20 4.0 ± 0.1 0.30 ± 0.05 4.0 ± 0.1 Ø1.55 ± 0.05 1.75 ± 0.10 7.5 ± 0.1 13.2 ± 0.2 16.0 ± 0.3 10.30 ± 0.20 0.1 MAX 10.30 ± 0.20 Ø1.6 ± 0.1 User Direction of Feed Corporate Headquarters QT Optoelectronics 610 North Mary Avenue Sunnyvale, CA 94086 (408) 720-1440 Phone (408) 720-0848 Fax European Sales QT Optoelectronics “Le Levant” 2, rue du Nouveau Bercy F-94277-CHARENTON-LE PONT Cedex FRANCE 33 [0] 1.45.18.78.78 Phone 33 [0] 1.43.75.77.57 Fax North American Sales QT Optoelectronics 16775 Addison Rd.,Suite 200 Addison, TX 75001 (972) 447-1300 Phone (972) 447-0784 Fax Asia/Pacific Sales QT Optoelectronics B613, 6th Floor East Wing, Wisma Tractors Jalan SS16/1, Subang Jaya 47500 Petaling Jaya Selangor Darul Eshan, Malaysia 603/735-2417 Phone 603/736-3382 Fax European Sales Quality Technologies Deutschland GmbH Max-Huber-Strasse 8 D-85737 Ismaning, Germany 49 [0] 89/96.30.51 Phone 49 [0] 89/96.54.74 Fax European Sales Quality Technologies (U.K) Ltd. 10, Prebendal Court, Oxford Road Aylesbury, Buckinghamshire HP19-3EY United Kingdom 44 [0] 1296/30.44.99 Phone 44 [0] 1296/39.24.32 Fax www.qtopto.com Call QT Optoelectronics for more information or the phone number of your nearest distributor. United States 800-533-6786 • France 33 [0] 1.45.18.78.78 • Germany 49 [0] 89/96.30.51 • United Kingdom 44 [0] 1296 394499 • Asia/Pacific 603-7352417 200004A