LPC662AIM

LPC662 LPC662 Low Power CMOS Dual Operational Amplifier Literature Number: SNOS555B LPC662 Low Power CMOS Dual Operational Amplifier General Description The LPC662 CMOS Dual operational amplifier is ideal for operation from a single supply. It features a wide range of operating voltage from +5V to +15V, rail-to-rail output swing in addition to an input common-mode range that includes ground. Performance limitations that have plagued CMOS amplifiers in the past are not a problem with this design. Input VOS, drift, and broadband noise as well as voltage gain (into 100 kΩ and 5 kΩ) are all equal to or better than widely accepted bipolar equivalents, while the power supply requirement is typically less than 0.5 mW. This chip is built with National’s advanced Double-Poly Silicon-Gate CMOS process. See the LPC660 datasheet for a Quad CMOS operational amplifier and LPC661 for a single CMOS operational amplifier with these same features. Applications n High-impedance buffer n Precision current-to-voltage converter n n n n n Long-term integrator High-impedance preamplifier Active filter Sample-and-Hold circuit Peak detector Features n n n n n n n n n n n n Rail-to-rail output swing Micropower operation ( < 0.5 mW) Specified for 100 kΩ and 5 kΩ loads High voltage gain 120 dB Low input offset voltage 3 mV Low offset voltage drift 1.3 µV/˚C Ultra low input bias current 2 fA Input common-mode includes GND Operating range from +5V to +15V Low distortion 0.01% at 1 kHz Slew rate 0.11 V/µs Full military temperature range available Application Circuit Howland Current Pump DS010548-23 © 2001 National Semiconductor Corporation DS010548 www.national.com LPC662 Low Power CMOS Dual Operational Amplifier August 2000 LPC662 Absolute Maximum Ratings (Note 3) Current at Power Supply Pin Voltage at Input/Output Pin If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/Distributors for availability and specifications. Operating Ratings (Note 3) ± Supply Voltage Differential Input Voltage Supply Voltage (V+ − V−) Output Short Circuit to V+ Output Short Circuit to V− Lead Temperature (Soldering, 10 sec.) Storage Temp. Range Junction Temperature ESD Rating (C = 100 pF, R = 1.5 kΩ) Power Dissipation Current at Input Pin Current at Output Pin 35 mA (V+) + 0.3V, (V−) −0.3V Temperature Range LPC662AMJ/883 LPC662AM LPC662AI LPC662I Supply Range Power Dissipation Thermal Resistance (θJA) (Note 10) 8-Pin Ceramic DIP 8-Pin Molded DIP 8-Pin SO 8-Pin Side Brazed Ceramic DIP 16V (Note 11) (Note 1) 260˚C −65˚C to +150˚C 150˚C 1000V (Note 2) ± 5 mA ± 18 mA −55˚C ≤ TJ ≤ +125˚C −55˚C ≤ TJ ≤ +125˚C −40˚C ≤ TJ ≤ +85˚C −40˚C ≤ TJ ≤ +85˚C 4.75V to 15.5V (Note 9) 100˚C/W 101˚C/W 165˚C/W 100˚C/W DC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C. Boldface limits apply at the temperature extremes. V+ = 5V, V− = 0V, VCM = 1.5V, VO = 2.5V and RL > 1M unless otherwise specified. Parameter Conditions Typ LPC662AM LPC662AI LPC662AMJ/883 Limit LPC662I Limit Limit (Note 4) (Note 4) Units (Notes 4, 8) Input Offset Voltage 1 Input Offset Voltage 3 3 6 mV 3.5 3.3 6.3 max 1.3 µV/˚C Average Drift Input Bias Current 0.002 20 100 Input Offset Current 0.001 0V ≤ VCM ≤ 12.0V 83 + Rejection Ratio V = 15V Positive Power Supply 5V ≤ V+ ≤ 15V Rejection Ratio VO = 2.5V Negative Power Supply 0V ≤ V− ≤ −10V 83 94 Input Common-Mode V+ = 5V and 15V Voltage Range For CMRR ≥ 50 dB Voltage Gain RL = 100 kΩ (Note 5) 100 2 2 max 70 70 63 dB 68 68 61 min 70 70 63 dB 68 68 61 min 20 pA Tera Ω 84 84 74 dB 83 73 min −0.4 −0.1 −0.1 −0.1 V 0 0 0 max V+ − 1.9 V+ − 2.3 V+ − 2.3 V+ − 2.3 V V+ − 2.6 V+ − 2.5 V+ − 2.5 min 400 400 300 V/mV 250 300 200 min 180 180 90 V/mV 70 120 70 min 200 200 100 V/mV 150 160 80 min 100 100 50 V/mV 35 60 40 min 1000 Sourcing Sinking RL = 5 kΩ (Note 5) 500 1000 Sourcing Sinking www.national.com max 82 Rejection Ratio Large Signal 4 >1 Input Resistance Common Mode pA 4 250 2 (Continued) Unless otherwise specified, all limits guaranteed for TJ = 25˚C. Boldface limits apply at the temperature extremes. V+ = 5V, V− = 0V, VCM = 1.5V, VO = 2.5V and RL > 1M unless otherwise specified. LPC662AM Parameter Conditions Typ LPC662AI LPC662I LPC662AMJ/883 Limit Limit Limit (Note 4) (Note 4) Units 4.970 4.940 V min (Notes 4, 8) Output Swing V+ = 5V 4.987 4.970 4.950 4.950 4.910 0.004 0.030 0.030 0.060 V 0.050 0.050 0.090 max 4.940 4.850 4.850 4.750 V 4.750 4.750 4.650 min 0.040 0.150 0.150 0.250 V 0.250 0.250 0.350 max + RL = 100 kΩ to V /2 V+ = 5V + RL = 5 kΩ to V /2 V+ = 15V 14.970 RL = 100 kΩ to V+/2 0.007 V+ = 15V 14.840 RL = 5 kΩ to V+/2 0.110 Output Current Sourcing, VO = 0V 22 V+ = 5V Sinking, VO = 5V Output Current Sourcing, VO = 0V 21 40 V+ = 15V Sinking, VO = 13V 39 (Note 11) Supply Current Both Amplifiers 86 VO = 1.5V 3 14.920 14.920 14.880 V 14.880 14.880 14.820 min 0.030 0.030 0.060 V 0.050 0.050 0.090 max 14.680 14.680 14.580 V 14.600 14.600 14.480 min 0.220 0.220 0.320 V 0.300 0.300 0.400 max 16 16 13 mA 12 14 11 min 16 16 13 mA 12 14 11 min 19 28 23 mA 19 25 20 min 19 28 23 mA 19 24 19 min 120 120 140 µA 145 140 160 max www.national.com LPC662 DC Electrical Characteristics LPC662 AC Electrical Characteristics Unless otherwise specified, all limits guaranteed for TJ = 25˚C. Boldface limits apply at the temperature extremes. V+ = 5V, V− = 0V, VCM = 1.5V, VO = 2.5V and RL > 1M unless otherwise specified. Parameter Conditions Typ LPC662AM LPC662AI LPC662I LPC662AMJ/883 Limit Limit Limit (Note 4) (Note 4) Units (Notes 4, 8) Slew Rate (Note 6) 0.11 Gain-Bandwidth Product 0.07 0.07 0.05 V/µs 0.04 0.05 0.03 min 0.35 MHz Phase Margin 50 Deg Gain Margin 17 dB dB Amp-to-Amp Isolation (Note 7) 130 Input Referred Voltage Noise F = 1 kHz 42 Input Referred Current Noise F = 1 kHz 0.0002 Total Harmonic Distortion F = 1 kHz, AV = −10, V+ = 15V 0.01 % RL = 100 kΩ, VO = 8 VPP Note 1: Applies to both single supply and split supply operation. Continuous short circuit operation at elevated ambient temperature and/or multiple Op Amp shorts can result in exceeding the maximum allowed junction temperature of 150˚C. Output currents in excess of ± 30 mA over long term may adversely affect reliability. Note 2: The maximum power dissipation is a function of TJ(max), θJA, and TA. The maximum allowable power dissipation of any ambient temperature is PD = (TJ(max) − TA)/θJA. Note 3: Absolute Maximum Ratings indicate limits beyond which damage to the device may occur. Operating Ratings indicate conditions for which the device is intended to be functional, but do not guarantee specific performance limits. For guaranteed specifications and test conditions, see the Electrical Characteristics. The guaranteed specifications apply only for the test conditions listed. Note 4: Limits are guaranteed by testing or correlation. Note 5: V+ = 15V, VCM = 7.5V and RL connected to 7.5V. For Sourcing tests, 7.5V ≤ VO ≤ 11.5V. For Sinking tests, 2.5V ≤ VO ≤ 7.5V. Note 6: V+ = 15V. Connected as Voltage Follower with 10V step input. Number specified is the slower of the positive and negative slew rates. Note 7: Input referred. V+ = 15V and RL = 100 kΩ connected to V+/2. Each amp excited in turn with 1 kHz to produce VO = 13 VPP. Note 8: A military RETS electrical test specification is available on request. At the time of printing, the LPC662AMJ/883 RETS specification complied fully with the boldface limits in this column. The LPC662AMJ/883 may also be procured to a Standard Military Drawing specification. Note 9: For operating at elevated temperatures the device must be derated based on the thermal resistance θJA with PD = (TJ − TA)/θJA. Note 10: All numbers apply for packages soldered directly into a PC board. Note 11: Do not connect output to V+when V+ is greater than 13V or reliability may be adversely affected. www.national.com 4 VS = ± 7.5V, TA = 25˚C unless otherwise specified Supply Current vs Supply Voltage Input Bias Current vs Temperature DS010548-28 Input Common-Mode Voltage Range vs Temperature LPC662 Typical Performance Characteristics DS010548-29 Output Characteristics Current Sinking DS010548-30 Output Characteristics Current Sourcing DS010548-31 Input Voltage Noise vs Frequency DS010548-32 DS010548-33 5 www.national.com LPC662 Typical Performance Characteristics VS = ± 7.5V, TA = 25˚C unless otherwise specified (Continued) Crosstalk Rejection vs Frequency CMRR vs Frequency DS010548-35 DS010548-34 CMRR vs Temperature Open-Loop Voltage Gain vs Temperature DS010548-36 DS010548-38 Open-Loop Frequency Response Gain and Phase Responses vs Load Capacitance DS010548-39 DS010548-40 www.national.com 6 VS = ± 7.5V, TA = 25˚C unless otherwise specified (Continued) Gain and Phase Responses vs Temperature Gain Error (VOSvs VOUT) DS010548-41 Non-Inverting Slew Rate vs Temperature DS010548-42 Inverting Slew Rate vs Temperature DS010548-43 Large-Signal Pulse Non-Inverting Response (AV = +1) DS010548-44 Non-Inverting Small Signal Pulse Response (AV = +1) DS010548-45 DS010548-46 7 www.national.com LPC662 Typical Performance Characteristics LPC662 Typical Performance Characteristics VS = ± 7.5V, TA = 25˚C unless otherwise specified (Continued) Inverting Large-Signal Pulse Response Inverting Small-Signal Pulse Response DS010548-47 DS010548-48 Power Supply Rejection Ratio vs Frequency DS010548-37 Stability vs Capacitive Load Stability vs Capacitive Load DS010548-4 DS010548-5 Note: Avoid resistive loads of less than 500Ω, as they may cause instability. www.national.com 8 tolerated without oscillation. Note that in all cases, the output will ring heavily when the load capacitance is near the threshold for oscillation. AMPLIFIER TOPOLOGY The topology chosen for the LPC662 is unconventional (compared to general-purpose op amps) in that the traditional unity-gain buffer output stage is not used; instead, the output is taken directly from the output of the integrator, to allow rail-to-rail output swing. Since the buffer traditionally delivers the power to the load, while maintaining high op amp gain and stability, and must withstand shorts to either rail, these tasks now fall to the integrator. As a result of these demands, the integrator is a compound affair with an embedded gain stage that is doubly fed forward (via Cf and Cff) by a dedicated unity-gain compensation driver. In addition, the output portion of the integrator is a push-pull configuration for delivering heavy loads. While sinking current the whole amplifier path consists of three gain stages with one stage fed forward, whereas while sourcing the path contains four gain stages with two fed forward. DS010548-7 FIGURE 2. Rx, Cx Improve Capacitive Load Tolerance Capacitive load driving capability is enhanced by using a pull up resistor to V+ Figure 3. Typically a pull up resistor conducting 50 µA or more will significantly improve capacitive load responses. The value of the pull up resistor must be determined based on the current sinking capability of the amplifier with respect to the desired output swing. Open loop gain of the amplifier can also be affected by the pull up resistor (see Electrical Characteristics). DS010548-6 FIGURE 1. LPC662 Circuit Topology (Each Amplifier) The large signal voltage gain while sourcing is comparable to traditional bipolar op amps for load resistance of at least 5 kΩ. The gain while sinking is higher than most CMOS op amps, due to the additional gain stage; however, when driving load resistance of 5 kΩ or less, the gain will be reduced as indicated in the Electrical Characteristics. The op amp can drive load resistance as low as 500Ω without instability. DS010548-26 FIGURE 3. Compensating for Large Capacitive Loads with A Pull Up Resistor PRINTED-CIRCUIT-BOARD LAYOUT FOR HIGH-IMPEDANCE WORK It is generally recognized that any circuit which must operate with less than 1000 pA of leakage current requires special layout of the PC board. When one wishes to take advantage of the ultra-low bias current of the LPC662, typically less than 0.04 pA, it is essential to have an excellent layout. Fortunately, the techniques for obtaining low leakages are quite simple. First, the user must not ignore the surface leakage of the PC board, even though it may sometimes appear acceptably low, because under conditions of high humidity or dust or contamination, the surface leakage will be appreciable. To minimize the effect of any surface leakage, lay out a ring of foil completely surrounding the LPC662’s inputs and the terminals of capacitors, diodes, conductors, resistors, relay terminals, etc. connected to the op-amp’s inputs. See Figure 4. To have a significant effect, guard rings should be placed on both the top and bottom of the PC board. This PC foil must then be connected to a voltage which is at the same voltage as the amplifier inputs, since no leakage current can flow between two points at the same potential. For example, a PC board trace-to-pad resistance of 1012 ohms, which is normally considered a very large resistance, could leak 5 pA if the trace were a 5V bus adjacent to the pad of an input. COMPENSATING INPUT CAPACITANCE Refer to the LMC660 or LMC662 datasheets to determine whether or not a feedback capacitor will be necessary for compensation and what the value of that capacitor would be. CAPACITIVE LOAD TOLERANCE Like many other op amps, the LPC662 may oscillate when its applied load appears capacitive. The threshold of oscillation varies both with load and circuit gain. The configuration most sensitive to oscillation is a unity-gain follower. See the Typical Performance Characteristics. The load capacitance interacts with the op amp’s output resistance to create an additional pole. If this pole frequency is sufficiently low, it will degrade the op amp’s phase margin so that the amplifier is no longer stable at low gains. The addition of a small resistor (50Ω to 100Ω) in series with the op amp’s output, and a capacitor (5 pF to 10 pF) from inverting input to output pins, returns the phase margin to a safe value without interfering with lower-frequency circuit operation. Thus, larger values of capacitance can be 9 www.national.com LPC662 Application Hints LPC662 Application Hints performance. See Figure 5a, Figure 5b, Figure 5c for typical connections of guard rings for standard op-amp configurations. If both inputs are active and at high impedance, the guard can be tied to ground and still provide some protection; see Figure 5d. (Continued) This would cause a 100 times degradation from the LPC662’s actual performance. However, if a guard ring is held within 5 mV of the inputs, then even a resistance of 1011 ohms would cause only 0.05 pA of leakage current, or perhaps a minor (2:1) degradation of the amplifier’s DS010548-19 FIGURE 4. Example of Guard Ring in P.C. Board Layout, using the LPC660 DS010548-22 (c) Follower DS010548-20 (a) Inverting Amplifier DS010548-21 (b) Non-Inverting Amplifier DS010548-23 (d) Howland Current Pump FIGURE 5. Guard Ring Connections The designer should be aware that when it is inappropriate to lay out a PC board for the sake of just a few circuits, there www.national.com is another technique which is even better than a guard ring on a PC board: Don’t insert the amplifier’s input pin into the 10 LPC662 Application Hints (Continued) board at all, but bend it up in the air and use only air as an insulator. Air is an excellent insulator. In this case you may have to forego some of the advantages of PC board construction, but the advantages are sometimes well worth the effort of using point-to-point up-in-the-air wiring. See Figure 6. DS010548-25 FIGURE 7. Simple Input Bias Current Test Circuit DS010548-24 A suitable capacitor for C2 would be a 5 pF or 10 pF silver mica, NPO ceramic, or air-dielectric. When determining the magnitude of I−, the leakage of the capacitor and socket must be taken into account. Switch S2 should be left shorted most of the time, or else the dielectric absorption of the capacitor C2 could cause errors. Similarly, if S1 is shorted momentarily (while leaving S2 shorted) (Input pins are lifted out of PC board and soldered directly to components. All other pins connected to PC board.) FIGURE 6. Air Wiring BIAS CURRENT TESTING The test method of Figure 7 is appropriate for bench-testing bias current with reasonable accuracy. To understand its operation, first close switch S2 momentarily. When S2 is opened, then where Cx is the stray capacitance at the + input. Typical Single-Supply Applications (V+ = 5.0 VDC) Photodiode Current-to-Voltage Converter Micropower Current Source DS010548-18 DS010548-17 Note: A 5V bias on the photodiode can cut its capacitance by a factor of 2 or 3, leading to improved response and lower noise. However, this bias on the photodiode will cause photodiode leakage (also known as its dark current). Note: (Upper limit of output range dictated by input common-mode range; lower limit dictated by minimum current requirement of LM385.) 11 www.national.com LPC662 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) Low-Leakage Sample-and-Hold DS010548-8 Instrumentation Amplifier DS010548-9 For good CMRR over temperature, low drift resistors should be used. Matching of R3 to R6 and R4 to R7 affects CMRR. Gain may be adjusted through R2. CMRR may be adjusted through R7. www.national.com 12 LPC662 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) Sine-Wave Oscillator DS010548-10 Oscillator frequency is determined by R1, R2, C1, and C2: fOSC = 1/2πRC where R = R1 = R2 and C = C1 = C2. This circuit, as shown, oscillates at 2.0 kHz with a peak-to-peak output swing of 4.5V 1 Hz Square-Wave Oscillator Power Amplifier DS010548-12 DS010548-11 13 www.national.com LPC662 Typical Single-Supply Applications (V+ = 5.0 VDC) (Continued) 10 Hz Bandpass Filter 10 Hz High-Pass Filter (2 dB Dip) DS010548-14 DS010548-13 fO = 10 Hz Q = 2.1 Gain = −8.8 fc = 10 Hz d = 0.895 Gain = 1 1 Hz Low-Pass Filter (Maximally Flat, Dual Supply Only) High Gain Amplifier with Offset Voltage Reduction DS010548-15 DS010548-16 Gain = −46.8 Output offset voltage reduced to the level of the input offset voltage of the bottom amplifier (typically 1 mV), referred to VBIAS. www.national.com 14 LPC662 Connection Diagram 8-Pin DIP/SO DS010548-1 Top View Ordering Information Package Temperature Range Military 8-Pin Industrial LPC662AMD NSC Drawing Transport Media D08C Rail Side Brazed Ceramic DIP 8-Pin LPC662AIM Small Outline or LPC662IM 8-Pin LPC662AIN Molded DIP or LPC662IN 8-Pin LPC662AMJ/883 M08A Rail Tape and Reel N08E Rail J08A Rail Ceramic DIP 15 www.national.com LPC662 Physical Dimensions inches (millimeters) unless otherwise noted 8-Pin Cavity Dual-In-Line Package (D) Order Number LPC662AMD NS Package Number D08C Ceramic Dual-In-Line Package (J) Order Number LPC662AMJ/883 NS Package Number J08A www.national.com 16 LPC662 Physical Dimensions inches (millimeters) unless otherwise noted (Continued) 8-Pin Small Outline Molded Package (M) Order Number LPC662AIM or LPC662IM NS Package Number M08A 8-Pin Molded Dual-In-Line Package (N) Order Number LPC662AIN or LPC662IN NS Package Number N08E 17 www.national.com LPC662 Low Power CMOS Dual Operational Amplifier Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Audio www.ti.com/audio Communications and Telecom www.ti.com/communications Amplifiers amplifier.ti.com Computers and Peripherals www.ti.com/computers Data Converters dataconverter.ti.com Consumer Electronics www.ti.com/consumer-apps DLP® Products www.dlp.com Energy and Lighting www.ti.com/energy DSP dsp.ti.com Industrial www.ti.com/industrial Clocks and Timers www.ti.com/clocks Medical www.ti.com/medical Interface interface.ti.com Security www.ti.com/security Logic logic.ti.com Space, Avionics and Defense www.ti.com/space-avionics-defense Power Mgmt power.ti.com Transportation and Automotive www.ti.com/automotive Microcontrollers microcontroller.ti.com Video and Imaging RFID www.ti-rfid.com OMAP Mobile Processors www.ti.com/omap Wireless Connectivity www.ti.com/wirelessconnectivity TI E2E Community Home Page www.ti.com/video e2e.ti.com Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2011, Texas Instruments Incorporated