STTH1502FP

STTH1502 Ultrafast recovery diode Main product characteristics IF(AV) VRRM Tj (max) VF (typ) trr (typ) 15 A 200 V 175° C 0.85 V 20 ns A K K Features and benefits ■ ■ ■ ■ ■ A K TO-220AC STTH1502D A K TO-220FPAC STTH1502FP Very low conduction losses Negligible switching losses Low forward and reverse recovery time High junction temperature Insulated packages – TO-220FPAC Electrical insulation 2000 VDC – TO-220AC Ins Electrical insulation 2500 VRMS A K TO-220AC Ins STTH1502DI Description The STTH1502 uses ST's new 200V planar Pt doping technology, and is specially suited for switching mode base drive and transistor circuits. Packaged in TO-220AC, TO-220FPAC, and TO-220 Ins, this device is intended for use in low voltage, high frequency inverters, free wheeling and polarity protection. Order codes Part Number STTH1502D STTH1502FP STTH1502DI Marking STTH1502 STTH1502 STTH1502DI October 2006 Rev 2 www.st.com 1/10 Characteristics STTH1502 1 Table 1. Symbol VRRM IF(RMS) Characteristics Absolute ratings (limiting values at Tj = 25° C, unless otherwise specified) Parameter Repetitive peak reverse voltage RMS forward current TO-220AC IF(AV) Average forward current, δ = 0.5 TO-220AC Ins TO-220FPAC IFSM Tstg Tj Surge non repetitive forward current Storage temperature range Maximum operating junction temperature tp = 10 ms Sinusoidal Tc = 130° C Tc = 105° C Tc = 85° C 150 -65 to + 175 175 A °C °C 15 A Value 200 32 Unit V A Table 2. Thermal parameters Parameter TO-220AC Value 2.5 3.8 5 ° C/W Unit Symbol Rth(j-c) Junction to case TO-220AC Ins TO-220FPAC Table 3. Symbol IR(1) Static electrical characteristics Parameter Reverse leakage current Test conditions Tj = 25° C Tj = 125° C Tj = 25° C Tj = 150° C VR = VRRM Min. Typ Max. 10 µA 10 1 IF = 15 A IF = 30 A IF = 30 A 0.85 1.05 1.15 1 100 1.1 0.95 1.20 1.3 1.15 V Unit VF(2) Forward voltage drop Tj = 125° C Tj = 25° C Tj = 150° C 1. Pulse test: tp = 5 ms, δ < 2 % 2. Pulse test: tp = 380 µs, δ < 2 % To evaluate the conduction losses use the following equation: P = 0.74 x IF(AV) + 0.014 IF2(RMS) 2/10 STTH1502 Table 4. Symbol Characteristics Dynamic characteristics Parameter Test conditions IF = 1 A, dIF/dt = -50 A/µs, VR = 30 V, Tj = 25° C IF = 1 A, dIF/dt = -100 A/µs, VR = 30 V, Tj = 25° C Min. Typ 28 20 5.7 200 1.3 Max. 36 25 7.2 A ns V Unit ns trr Reverse recovery time IRM tfr VFP Reverse recovery current Forward recovery time Forward recovery voltage IF = 15 A, dIF/dt = -200 A/µs, VR = 160 V, Tj = 125° C IF = 15 A, dIF/dt = 50 A/µs VFR = 1.1 x VFmax, Tj = 25° C IF = 15 A, dIF/dt = 50 A/µs, Tj = 25° C Figure 1. IM(A) 100 Peak current versus duty cycle Figure 2. Forward voltage drop versus forward current (typical values) T IM 200 180 tp IFM(A) 80 P = 20 W δ d=tp/T 160 140 120 100 60 P = 10 W 40 P=5W 80 60 40 20 Tj=150°C Tj=25°C 20 δ 0 0.0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 1.0 VFM(V) 0.0 0.5 1.0 1.5 2.0 2.5 3.0 0 Figure 3. Forward voltage drop versus forward current (maximum values) Figure 4. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220AC) IFM(A) 200 180 160 140 120 100 80 60 40 20 0 0.0 0.5 1.0 1.5 2.0 2.5 3.0 Tj=25°C Tj=150°C Zth(j-c)/Rth(j-c) 1.0 Single pulse TO-220AC TO-220ACins VFM(V) tp(s) 0.1 1.E-03 1.E-02 1.E-01 1.E+00 3/10 Characteristics STTH1502 Figure 5. Relative variation of thermal impedance, junction to case, versus pulse duration (TO-220FPAC) Figure 6. Junction capacitance versus reverse applied voltage (typical values) 1.0 Zth(j-c)/Rth(j-c) Single pulse TO-220FPAC C(pF) 100 F=1MHz Vosc=30mVRMS Tj=25°C 0.1 tp(s) 0.0 1.E-03 1.E-02 1.E-01 1.E+00 1.E+01 10 1 10 100 VR(V) 1000 Figure 7. QRR(nC) 200 IF=15A VR=160V Reverse recovery charges versus dIF/dt (typical values) Figure 8. tRR(ns) 80 70 60 Reverse recovery time versus dIF/dt (typical values) IF=15A VR=160V 150 Tj=125°C 50 40 30 Tj=25°C Tj=125°C 100 50 Tj=25°C 20 10 dIF/dt(A/µs) dIF/dt(A/µs) 0 500 0 0 50 100 150 200 250 300 350 400 450 10 100 1000 Figure 9. IRM(A) 16 14 12 10 8 IF=15A VR=160V Peak reverse recovery current versus dIF/dt (typical values) Figure 10. Dynamic parameters versus junction temperature QRR; IRM [T j] / Q RR; IRM [T j=125°C] 1.4 1.2 1.0 IF=15A VR=160V Tj=125°C 0.8 0.6 IRM 6 Tj=25°C QRR 4 2 dIF/dt(A/µs) 0 0 50 100 150 200 250 300 350 400 450 500 0.4 0.2 Tj(°C) 0.0 25 50 75 100 125 150 4/10 STTH1502 Ordering information scheme 2 Ordering information scheme STTH Ultrafast switching diode Average forward current 15 = 15 A Repetitive peak reverse voltage 02 = 200 V Package D = TO-220AC FP = TO-220FPAC DI = TO-220AC Ins 15 02 XX 5/10 Package information STTH1502 3 Package information Epoxy meets UL94, V0 Cooling method: by conduction (C) Recommended torque value: 0.8 Nm Maximum torque value: 1.0 Nm Table 5. T0-220AC dimensions DIMENSIONS REF. Millimeters Min. A H2 ØI L5 L7 L6 L2 C A Inches Min. 0.173 0.048 0.094 0.019 0.024 0.044 0.194 0.393 Max. 0.181 0.051 0.107 0.027 0.034 0.066 0.202 0.409 Max. 4.60 1.32 2.72 0.70 0.88 1.70 5.15 10.40 4.40 1.23 2.40 0.49 0.61 1.14 4.95 10.00 C D E F F1 G F1 L9 L4 F D H2 L2 M E G 16.40 typ. 13.00 2.65 15.25 6.20 3.50 14.00 2.95 15.75 6.60 3.93 0.645 typ. 0.511 0.104 0.600 0.244 0.137 0.551 0.116 0.620 0.259 0.154 L4 L5 L6 L7 L9 M Diam. I 2.6 typ. 3.75 3.85 0.102 typ. 0.147 0.151 6/10 STTH1502 Table 6. T0-220FPAC dimensions Package information DIMENSIONS REF Millimeters Min. A A H B Inches Min. 0.173 0.098 0.098 0.018 0.030 0.045 0.195 0.094 0.393 Max. 0.181 0.106 0.108 0.027 0.039 0.067 0.205 0.106 0.409 Max. 4.6 2.7 2.75 0.70 1 1.70 5.20 2.7 10.4 4.4 2.5 2.5 0.45 0.75 1.15 4.95 2.4 10 B D Dia L6 L2 L3 L5 F1 L4 D L7 E F F1 G G1 H L2 16 Typ. 28.6 9.8 2.9 15.9 9.00 3.00 30.6 10.6 3.6 16.4 9.30 3.20 0.63 Typ. 1.126 0.386 0.114 0.626 0.354 0.118 1.205 0.417 0.142 0.646 0.366 0.126 F G1 G E L3 L4 L5 L6 L7 Dia. 7/10 Package information Table 7. TO-220AC Ins. dimensions Dimensions Ref. Millimeters Min. A B ØI L F b2 C STTH1502 Inches Min. Typ. Max. 0.625 0.147 Typ. Max. 15.20 3.75 13.00 10.00 0.61 1.23 4.40 0.49 2.40 4.80 6.20 3.75 15.90 0.598 a1 a2 B b1 14.00 0.511 10.40 0.393 0.88 0.024 1.32 0.048 4.60 0.173 0.70 0.019 2.72 0.094 5.40 0.189 6.60 0.244 3.85 0.147 0.551 0.409 0.034 0.051 0.181 0.027 0.107 0.212 0.259 0.151 A I4 b2 C c2 a1 l2 c1 c2 e a2 M b1 e c1 F ØI I4 L l2 M 15.80 16.40 16.80 0.622 0.646 0.661 2.65 1.14 2.60 2.95 0.104 1.70 0.044 0.102 0.116 0.066 In order to meet environmental requirements, ST offers these devices in ECOPACK® packages. These packages have a lead-free second level interconnect. The category of second level interconnect is marked on the package and on the inner box label, in compliance with JEDEC Standard JESD97. The maximum ratings related to soldering conditions are also marked on the inner box label. ECOPACK is an ST trademark. ECOPACK specifications are available at: www.st.com. 8/10 STTH1502 Ordering information 4 Ordering information Part Number STTH1502D STTH1502FP STTH1502DI Marking STTH1502 STTH1502 STTH1502DI Package TO-220AC TO-220FPAC TO-220AC Ins Weight 1.86 g 2.2 g 1.86 Base qty 50 50 50 Delivery mode Tube Tube Tube 5 Revision history Date 05-Apr-2006 10-Oct-2006 Revision 1 2 First issue Added TO-220AC Ins package Description of Changes 9/10 STTH1502 Please Read Carefully: Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any time, without notice. All ST products are sold pursuant to ST’s terms and conditions of sale. Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no liability whatsoever relating to the choice, selection or use of the ST products and services described herein. No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such third party products or services or any intellectual property contained therein. UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT. UNLESS EXPRESSLY APPROVED IN WRITING BY AN AUTHORIZED ST REPRESENTATIVE, ST PRODUCTS ARE NOT RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY, DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK. Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any liability of ST. ST and the ST logo are trademarks or registered trademarks of ST in various countries. Information in this document supersedes and replaces all information previously supplied. The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners. © 2006 STMicroelectronics - All rights reserved STMicroelectronics group of companies Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America www.st.com 10/10