CLC401AJ

CLC401 Fast Settling, Wideband High Gain Monolithic Op Amp General Description The CLC401 is a wideband, fast settling op amp designed for applications requiring gains greater than ± 7. Constructed using an advanced complementary bipolar process and a proprietary design, the CLC401 features dynamic performance far beyond that of typical high speed monolithic op amps. For example, at a gain of +20, the −3dB bandwidth is 150MHz and the rise/fall time is only 2.5ns. The wide bandwidth and linear phase (0.2˚ deviation from linear at 50MHz) and a very flat gain response makes the CLC401 ideal for many digital communication system applications. For example, demodulators need both DC coupling and high frequency amplification-requirements that are ordinarily difficult to meet. The very fast 10ns settling to 0.1% and the ability to drive capacitive loads lend themselves well to flash A/D applications. Systems employing D/A converters also benefit from the settling time and also by the fact that current-to-voltage transimpedance amplification is easily accomplished. The CLC401 provides a quick, effective design solution. Its stable operation over the entire ± 7 to ± 50 gain range precludes the need for external compensation. And, unlike many other high speed-op amps, the CLC401’s power dissipation of 150mW is compatible with designs which must limit total power dissipation or power supply requirements. The CLC401 is based on National’s proprietary op amp topology that uses current feedback instead of the usual voltage feedback. This unique design has many advantages over conventional designs (such as settling time that is relatively independent of gain), yet it is used in basically the same way (see the gain equations in Figure 1 and Figure 2). However, an understanding of the topology will aid in achieving the best performance. The discussion below will proceed for the non-inverting gain configuration with the inverting mode analysis being very similar. Enhanced Solutions (Military/Aerospace) SMD Number: 5962-89973 Space level versions also available. For more information, visit http://www.national.com/mil Features n n n n n n −3dB bandwidth of 150MHz 0.1% settling in 10ns Low power, 150mW Overload and short circuit protected Stable without compensation Recommended gain range, ± 7 to ± 50 Applications n n n n n n n Flash, precision A/D conversion Photodiode, CCD preamps IF processors High speed modems, radios Line drivers DC coupled log amplifiers High speed communications Pulse Response DS012744-18 Connection Diagram DS012744-17 Pinout DIP & SOIC © 2001 National Semiconductor Corporation DS012744 www.national.com CLC401 Fast Settling, Wideband High Gain Monolithic Op Amp February 2001 CLC401 Connection Diagram (Continued) DS012744-1 Non-Inverting Frequency Response Ordering Information Package Temperature Range Industrial Part Number Package Marking NSC Drawing 8-pin plastic DIP −40˚C to +85˚C CLC401AJP CLC401AJP N08E 8-pin plastic SOIC −40˚C to +85˚C CLC401AJE CLC401AJE M08A www.national.com 2 Junction Temperature Range Operating Temperature Range Storage Temperature Range Lead Solder Duration (+300˚C) If Military/Aerospace specified devices are required, please contact the National Semiconductor Sales Office/ Distributors for availability and specifications. ± 7V Supply Voltage (VCC) IOUT Output is short circuit protected to ground, but maximum reliability will be maintained if IOUT does not exceed... Common Mode Input Voltage Differential Input Voltage +150˚C −40˚C to +85˚C −65˚C to +150˚C 10 sec Operating Ratings Thermal Resistance Package (θJC) MDIP 70˚C/W SOIC 65˚C/W 60mA ± VCC 5V (θJA) 125˚C/W 145˚C/W Electrical Characteristics (AV = +20, VCC = ± 5V, RL = 100Ω, Rf =1.5kΩ; unless specified). Symbol Parameter Ambient Temperature Conditions CLC401AJ Typ Max/Min Ratings (Note 2) Units +25˚C −40˚C +25˚C +85˚C VOUT < 2VPP 150 100 > 100 > 65 > 70 > 55 MHz VOUTt < 5VPP > 100 > 65 < 0.1 < 0.2 < 1.0 < 1.0 < 0.1 < 0.2 < 1.0 < 1.0 < 0.1 < 0.2 < 1.3 < 1.5 dB < 3.5 < 7.0 < 15 < 10 > 800 < 3.5 < 7.0 < 15 < 10 > 800 < 5.0 < 8.0 < 15 < 10 > 700 Frequency Domain Response SSBW −3dB Bandwidth LSBW Gain Flatness GFPL Peaking GFPH Peaking GFR Rolloff LPD Linear Phase Deviation MHz VOUT < 2VPP < 25MHz > 25MHz < 50MHz 0.2 DC to 50MHz 0.2 0 0 dB dB deg Time Domain Response TRS Rise and Fall Time TRL 2V Step 2.5 5V Step 5 10 TS Settling Time to ± 0.1% 2V Step OS Overshoot 2V Step SR Slew Rate 0 1200 ns ns ns % V/µs Distortion And Noise Response HD2 2nd Harmonic Distortion 2VPP, 20MHz −45 3rd Harmonic Distortion 2VPP, 20MHz −60 < −35 < −50 < −35 < −50 < −35 < −45 dBc HD3 −158 < −155 < −155 < −154 dBm (1Hz) 35 < 50 < 50 < 55 µV 3 ± 6.0 100 ± 10.0 ± 50 ± 36 ± 200 – ± 11.0 ± 50 ± 20 ± 100 nA/˚C 10 46 30 40 µA dBc Equivalent Input Noise SNF Noise Floor > 1MHz INV Integrated Noise 1MHz to 150MHz Static, DC Performance VIO DVIO IBN DIBN IBI Input Offset Voltage (Note 3) Average Temperature Coefficient Input Bias Current (Note 3) 20 Non-Inverting 10 Average Temperature Coefficient Input Bias Current (Note 3) Inverting – ± 20 mV µV/˚C µA 100 ± 200 – ± 100 nA/˚C PSRR Power Supply Rejection Ratio 55 50 50 50 dB CMRR Common Mode Rejection Ratio 55 50 50 50 dB ICC Supply Current (Note 3) No Load 15 21 21 21 mA > 50 < 2.5 < 0.3 > 3.0 > 100 < 2.5 < 0.3 > 3.2 > 100 < 2.5 < 0.3 > 3.2 kΩ DIBI Average Temperature Coefficient Miscellaneous Performance RIN Non-Inverting Input CIN Resistance 200 Capacitance 0.5 RO Output Impedance at DC 0.2 VO Output Voltage Range No Load 3.5 3 pF Ω V www.national.com CLC401 Absolute Maximum Ratings (Note 1) CLC401 Electrical Characteristics (Continued) (AV = +20, VCC = ± 5V, RL = 100Ω, Rf =1.5kΩ; unless specified). Symbol Parameter Conditions Typ Max/Min Ratings (Note 2) Units Miscellaneous Performance CMIR Common Mode Input Range IO Output Current For Rated Performance 2.8 60 > 2.0 > 35 > 2.5 > 50 > 2.5 > 50 V mA Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the devices should be operated at these limits. The table of “Electrical Characteristics” specifies conditions of device operation. Note 2: Max/min ratings are based on product characterization and simulation. Individual parameters are tested as noted. Outgoing quality levels are determined from tested parameters. Note 3: AJ-level: spec. is 100% tested at +25˚C. Typical Performance Characteristics (TA = 25˚, AV = +20, VCC = ± 5V, RL = 100Ω: Unless Specified). Non-Inverting Frequency Response Inverting Frequency Response DS012744-1 Frequency Response for Various RLs DS012744-2 Open-Loop Transimpedance Gain, Z(s) DS012744-3 DS012744-4 www.national.com 4 (TA = 25˚, AV = +20, VCC = ± 5V, RL = 100Ω: Unless Specified).. (Continued) 2nd and 3rd Harmonic Distortion 2-Tone,3rd Order, Intermodulation Intercept DS012744-6 DS012744-5 Equivalent Input Noise CMRR and PSRR DS012744-8 DS012744-7 Pulse Response Settling Time DS012744-19 DS012744-18 5 www.national.com CLC401 Typical Performance Characteristics CLC401 Typical Performance Characteristics (TA = 25˚, AV = +20, VCC = ± 5V, RL = 100Ω: Unless Specified).. (Continued) Long-Term Settling Time Settling Time vs. Load Capacitance DS012744-9 DS012744-20 Recommended RS vs. Load Capacitance Low Gain & Transimpedance Applications DS012744-21 DS012744-13 Frequency Response, AV = −1, Rf = 2.25kΩ DS012744-14 www.national.com 6 CLC401 Equation 1 Application Division where LG is the loop gain defined by, Equation 2 Equation 1 has a form identical to that for a voltage feedback amplifier with the differences occurring in the LG expression. For an idealized treatment, set Zi =0 which results in a very simple LG = Z(s)/Rf(Derivation of the transfer function for the case where Zi = 0 is given in Application Note AN300-1). Using the Z(s) (open-loop transimpedance gain) plot shown on the previous page and dividing by the recommended Rf = 1.5kΩ, yields a large loop gain at DC. As a result, Equation 1 shows that the closed-loop gain at DC is very close to (1+Rf/Rg). At higher frequencies, the roll-off of Z(s) determines the closed-loop frequency response which, ideally, is dependent only on Rf. The specifications reported on the previous pages are therefore valid only for the specified R = 1.5kΩ. Increasing R from 1.5kΩ will decrease the loop gain and band width, while decreasing it will increase the loop gain possibly leading to inadequate phase margin and closed-loop peaking. Conversely, fixing Rf will hold the frequency response constant while the closed-loop gain can be adjusted using Rg. The CLC401 departs from this idealized analysis to the extent that the inverting input impedance is finite. With the low quiescent power of the CLC401, Z = 50Ω leading to drop in loop gain and bandwidth at high gain settlings, as given by Equation 2. The second term is Equation 2 accounts for the division in feedback current that occurs between Zi and Rf\Rg at the inverting node of the CLC400. This decrease in bandwidth can be circumvented as described in “Increasing Bandwidth at High Gains.” DC Accuracy and Noise Since the two inputs for the CLC401 are quite dissimilar, the noise and offset error performance differs somewhat from that of a standard differential input amplifier. Specifically, the inverting input current noise is much larger than the non-inverting current noise. Also the two input bias currents are physically unrelated rendering bias current cancellation through matching of the inverting and non-inverting pin resistors ineffective. In Equation 3, the output offset is the algebraic sum of the equivalent input voltage and current sources that influence DC operation. Output noise is determined similarly except that a root-sum-of-squares replaces the algebraic sum. Rs is the non-inverting pin resistance. Equation 3 Output Offset VO = ± IBN x RS (1+ Rf/Rg) ± VIO (1+ Rf/Rg) ± IBI x Rf DS012744-15 FIGURE 1. Recommended Non-Inverting Gain Circuit DS012744-16 FIGURE 2. Recommended Inverting Gain Circuit Understanding the Loop Gain Referring to the equivalent circuit of Figure 3, any current flowing in the inverting input is amplified to a voltage at the output through the transimpedance gain shown on the plots on page 3. This Z(s) is analogous to the open-loop gain of a voltage feedback amplifier. DS012744-22 FIGURE 3. Current feedback topology Developing the non-inverting frequency response for the topology of Figure 3 yields: An important observation is that for fixed Rf, offsets as referred to the input improve as the gain is increased (divide all terms by 1+Rf/Rg). A similar result is obtained for noise where noise figure improves as gain increases. Selecting Between the CLC400 or CLC401 7 www.national.com CLC401 Application Division Capacitive Feedback (Continued) Capacitive feedback should not be used with the CLC401 because of the potential for loop instability. See Application Note OA-7 for active filter realizations with the CLC401. The CLC400 is intended for gains of ± 1 to ± 8 while the CLC401 is designed for gains of ± 7 to ± 50. Optimum performance is achieved with a feedback resistor of 250Ω with the CLC400 and 1.5Ω with the CLC401- this distinction may be important in transimpedance applications such as D/A buffering. Although the CLC400 can be used at higher gains, the CLC401 will provide a wider bandwidth because loop gain losses due to finite Zi are lower with the larger CLC401 feedback resistor as explained above. On the other hand, the lower recommended feedback resistance of the CLC400 minimizes the output errors due to inverting input noise and bias currents. Increasing Bandwidth At High Gains Bandwidth may be increased at high closed-loop gains by adjusting Rf and Rgto make up for the losses in loop gain that occur at these high gain settlings due to current division at the inverting input. An approximate relationship my be obtained by holding the LG expression constant as the gain is changed from the design point used in the specifications (that is, Rf = 1.5kΩ and Rg = 79Ω). For the CLC401 this gives, Equation 4 Printed Circuit Layout As with any high frequency device, a good PCB layout will enhance performance. Ground plane construction and good power supply bypassing close to the package are critical to achieving full performance. In the non-inverting configuration, the amplifier is sensitive to stray capacitance to ground at the inverting input. Hence, the inverting node connections should be small with minimal coupling to the ground plane. Shunt capacitance across the feedback resistor should not be used to compensate for this effect. Parasitic or load capacitance directly on the output will introduce additional phase shift in the loop degrading the loop phase margin and leading to frequency response peaking. A small series resistor before the capacitance effectively decouples this effect. The graphs on the preceding page illustrate the required resistor value and resulting performance vs. capacitance. Precision buffed resistors (PRP8351 series from Precision Resistive Products) with low parasitic reactances were used to develop the data sheet specifications. Precision carbon composition resistors will also yield excellent results. Standard spirally-trimmed RN55D metal film resistors will work with the slight decrease in bandwidth due to their reactive nature at high frequencies. Evaluation PC boards (part no. CLC730013 for through-hole and CLC730027 for SOIC) for the CLC401 are available. where AVis the desired non-inverting gain. Note that with AV = +20 we get the specified Rf = 1.5kΩ, while at higher gains, a lower value gives stable performance with improved bandwidth. www.national.com 8 CLC401 Physical Dimensions inches (millimeters) unless otherwise noted NS Product Number M08A NS Product Number N08E 9 www.national.com CLC401 Fast Settling, Wideband High Gain Monolithic Op Amp Notes LIFE SUPPORT POLICY NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. National Semiconductor Corporation Americas Tel: 1-800-272-9959 Fax: 1-800-737-7018 Email: support@nsc.com www.national.com National Semiconductor Europe Fax: +49 (0) 180-530 85 86 Email: europe.support@nsc.com Deutsch Tel: +49 (0) 69 9508 6208 English Tel: +44 (0) 870 24 0 2171 Français Tel: +33 (0) 1 41 91 8790 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. National Semiconductor Asia Pacific Customer Response Group Tel: 65-2544466 Fax: 65-2504466 Email: ap.support@nsc.com National Semiconductor Japan Ltd. Tel: 81-3-5639-7560 Fax: 81-3-5639-7507 National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications. National P/N CLC401 - Fast Settling, Wideband High Gain Monolithic Op Amp Design · Purchasing · Quality · Company · Jobs National Semiconductor Corporation Home Products > Analog - Amplifiers > Operational Amplifiers > High Speed > 50MHz > CLC401 Product Folder CLC401 Fast Settling, Wideband High Gain Monolithic Op Amp Generic P/N 401 Contents Parametric Table Channels (Channels) 1 ● General Description Input Output Type Not Rail to Rail ● Features Bandwidth, typ (MHz) 179 ● Applications Slew Rate, typ (Volts/usec) 1200 ● Datasheet Supply Current per Channel, typ (mA) 15 ● Package Availability, Models, Samples & Pricing Minimum Supply Voltage (Volt) 10 Maximum Supply Voltage (Volt) 14 ● Design Tools Offset Voltage, Max (mV) 6 ● Application Notes Input Bias Current, Temp Max (nA) 36000 Output Current, typ (mA) 70 Voltage Noise, typ (nV/Hz) 2.40 Shut down No Feedback Type Current BW at Av+5 (MHz) 179 BW at Av+10 (MHz) 167 BW at Av+20 (MHz) 150 HD 2nd, typ (dB) -45 HD 3rd, typ (dB) -60 Settling Time 10nS to 0.1% Special Features AvCl>7 General Description file:///F|/cpl_new_images/CLC401.html (1 of 4) [7/18/2001 5:50:26 PM] National P/N CLC401 - Fast Settling, Wideband High Gain Monolithic Op Amp The CLC401 is a wideband, fast settling op amp designed for applications requiring gains greater than ±7. Constructed using an advanced complementary bipolar process and a proprietary design, the CLC401 features dynamic performance far beyond that of typical high speed monolithic op amps. For example, at a gain of +20, the -3dB bandwidth is 150MHz and the rise/fall time is only 2.5ns. The wide bandwidth and linear phase (0.2° deviation from linear at 50MHz) and a very flat gain response makes the CLC401 ideal for many digital communication system applications. For example, demodulators need both DC coupling and high frequency amplification-requirements that are ordinarily difficult to meet. The very fast 10ns settling to 0.1% and the ability to drive capacitive loads lend themselves well to flash A/D applications. Systems employing D/A converters also benefit from the settling time and also by the fact that current-to-voltage transimpedance amplification is easily accomplished. The CLC401 provides a quick, effective design solution. Its stable operation over the entire ±7 to ±50 gain range precludes the need for external compensation. And, unlike many other high speed-op amps, the CLC401's power dissipation of 150mW is compatible with designs which must limit total power dissipation or power supply requirements. The CLC401 is based on National's proprietary op amp topology that uses current feedback instead of the usual voltage feedback. This unique design has many advantages over conventional designs (such as settling time that is relatively independent of gain), yet it is used in basically the same way (see the gain equations in and ). However, an understanding of the topology will aid in achieving the best performance. The discussion below will proceed for the non-inverting gain configuration with the inverting mode analysis being very similar. Enhanced Solutions (Military/Aerospace) SMD Number: 5962-89973 Space level versions also available. For more information, visit http://www.national.com/mil Features ● ● ● ● ● ● -3dB bandwidth of 150MHz 0.1% settling in 10ns Low power, 150mW Overload and short circuit protected Stable without compensation Recommended gain range, ±7 to ±50 Applications ● ● ● ● ● ● ● Flash, precision A/D conversion Photodiode, CCD preamps IF processors High speed modems, radios Line drivers DC coupled log amplifiers High speed communications file:///F|/cpl_new_images/CLC401.html (2 of 4) [7/18/2001 5:50:26 PM] National P/N CLC401 - Fast Settling, Wideband High Gain Monolithic Op Amp Datasheet Size (in Kbytes) Title CLC401 Fast Settling, Wideband High Gain Monolithic Op Amp CLC401 Fast Settling, Wideband High Gain Monolithic Op Amp (JAPANESE) CLC401 Mil-Aero Datasheet MNCLC401A-X Date View Online 279 14-Nov-00 View Online Kbytes 339 Kbytes View Online 59 Kbytes View Online Download Download Download Download Receive via Email Receive via Email Receive via Email Receive via Email Please use Adobe Acrobat to view PDF file(s). If you have trouble printing, see Printing Problems. Package Availability, Models, Samples & Pricing Package Part Number CLC401AJE Type SOIC NARROW SOIC CLC401AJE-TR13 NARROW CLC401AJP MDIP Models # pins 8 Status SPICE IBIS Full clc401.cir N/A production 8 Full clc401.cir N/A production 8 Full clc401.cir N/A production 5962-8997301PA Cerdip 8 Full clc401.cir N/A production CLC401AJ Cerdip 8 Full clc401.cir N/A production CLC401AD-MLS SB Cerdip 8 Full clc401.cir N/A production CLC401AJ-MLS Cerdip 8 Full clc401.cir N/A production file:///F|/cpl_new_images/CLC401.html (3 of 4) [7/18/2001 5:50:26 PM] Samples & Electronic Orders Budgetary Pricing Std Pack Quantity $US each Size 1K+ $3.6500 tube of 95 [logo]¢2¢T CLC40 1AJE 1K+ reel $3.6800 of 2500 [logo]¢2¢T CLC40 1AJE 1K+ $3.6500 Samples Buy Now Buy Now Samples Buy Now Buy Now Package Marking 25+ 500+ 50+ tube of 40 [logo]¢U¢Z¢2¢T CLC401AJP [logo]¢Z¢S¢4¢A$E tube CLC401AJ-QML $29.1000 of 5962-8997301 40 PA tube [logo]¢U¢Z¢2¢T¢P $17.8000 of CLC401AJ 40 tube [logo]¢Z¢S¢4¢A of CLC401AD N/A -MLS $E tube [logo]¢Z¢S¢4¢A$E $220.0000 of CLC401AJ-MLS 40 National P/N CLC401 - Fast Settling, Wideband High Gain Monolithic Op Amp Design Tools Size (in Kbytes) Title Amplifiers Selection Guide software for Windows 9 Kbytes Date View Online Download Receive via Email View 19-Mar-2001 CLC730013EB 8-pin Op Amp Evaluation Board 130 Kbytes 2-Jan-2001 View Online Download Receive via Email CLC730027EB 8-pin Op Amp Evaluation Board 130 Kbytes 2-Jan-2001 View Online Download Receive via Email Please use Adobe Acrobat to view PDF file(s). If you have trouble printing, see Printing Problems. Application Notes Size (in Kbytes) Title OA-07: OA-07 Current- Feedback Op Amp Applications Circuit Guide OA-11: OA-11 A Tutorial on Applying Op Amps to RF Applications Date View Online Download Receive via Email 308 Kbytes 28-Oct-96 View Online Download Receive via Email 769 Kbytes 2-Apr-99 View Online Download Receive via Email OA-12: OA-12 Noise Analysis for Comlinear's Op Amps 108 Kbytes 24-Feb-99 View Online Download Receive via Email OA-13: OA-13 Current- Feedback Loop Gain Analysis 527 Kbytes 28-Oct-96 View Online Download Receive via Email OA-14: OA-14 Improving Amplifier Noise Figure for High 92 Kbytes 15-Dec-00 View Online Download 3rd Intercept Amplifiers OA-15: OA-15 Frequent Faux Pas in Applying Wideband 527 Kbytes 28-Jan-99 View Online Download Current Feedback Amplifiers OA-18: OA-18 Simulation SPICE Models for Comlinear's Op 337 Kbytes 23-May-00 View Online Download Amps OA-20: OA-20 Current Feedback Myths Debunked 139 Kbytes 10-Jul-97 View Online Download Receive via Email Receive via Email Receive via Email Receive via Email OA-25: OA-25 Stability Analysis of Current Feedback Amplifier 262 Kbytes 10-Oct-96 View Online Download Receive via Email OA-30: OA-30 Current vs. Voltage Feedback Amplifiers 56 Kbytes 5-Jun-98 View Online Download Receive via Email Please use Adobe Acrobat to view PDF file(s). If you have trouble printing, see Printing Problems. [Information as of 25-Apr-2001] Quick Search Parametric Search System Diagrams Product Tree About Languages . Website Guide . About "Cookies" . National is QS 9000 Certified Site Terms & Conditions of Use . Copyright 2001 © National Semiconductor Corporation Privacy/Security Statement . Preferences . Feedback file:///F|/cpl_new_images/CLC401.html (4 of 4) [7/18/2001 5:50:26 PM] Home